Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2021.07
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0441241 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly and transmission control switch (shift lock control unit assembly) (w/ Shift Paddle Switch) detect the shift lever position and send signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority Note
P070513 Transmission Range Sensor "A" Circuit Open Either of the following conditions is met for 60 seconds or more (2-trip detection logic).
w/ Shift Paddle Switch:
·

P, R, N and D input signals are all OFF simultaneously


w/o Shift Paddle Switch:
·

P, R, N, D and B input signals are all OFF simultaneously


·

Wire harness or connector

·

Park/neutral position switch assembly

·

TCM


Comes on DTC stored Transmission A SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure One of the following conditions is met for 2 seconds or more (2-trip detection logic).
w/ Shift Paddle Switch:
·

2 or more of the following signals are ON simultaneously*1:

-

P or N input signal

-

R input signal

-

D input signal


·

Any of the following signals are ON simultaneously with the shift lever in M*2:

-

P input signal

-

R input signal

-

N input signal



w/o Shift Paddle Switch:
·

2 or more of the following signals are ON simultaneously*3:

-

P or N input signal

-

R input signal

-

D input signal

-

B input signal



·

Wire harness or connector

·

Park/neutral position switch assembly

·

Transmission control switch (Shift lock control unit assembly) (w/ Shift Paddle Switch)

·

TCM


Comes on DTC stored Transmission A SAE Code:
P0705

DTC Detection Condition Patterns (P070562*1):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnostic Condition Ignition switch is ON ○ ○ ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○ ○ ○
Malfunction Condition P input signal is ON ○ ○ - - -
R input signal is ON ○ - ○ - ○
N input signal is ON - - ○ ○ -
D input signal is ON - ○ - ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P070562*2):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnostic Condition Ignition switch is ON ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○
Malfunction Condition P input signal is ON ○ - -
R input signal is ON - ○ -
N input signal is ON - - ○
M input signal is ON ○ ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P070562*3):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnostic Condition Ignition switch is ON ○ ○ ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○ ○ ○
Malfunction Condition P input signal is ON ○ ○ - - -
R input signal is ON ○ - ○ - ○
N input signal is ON - - ○ ○ -
D input signal is ON - ○ - ○ ○
B input signal is ON - - - - -
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

DTC Detection Condition Patterns (P070562*3):
Vehicle Condition
Pattern 6 Pattern 7 Pattern 8 Pattern 9
Diagnostic Condition Ignition switch is ON ○ ○ ○ ○
Battery voltage is 8 V or more ○ ○ ○ ○
Malfunction Condition P input signal is ON ○ - - -
R input signal is ON - - ○ -
N input signal is ON - ○ - -
D input signal is ON - - - ○
B input signal is ON ○ ○ ○ ○
Duration 2 seconds or more 2 seconds or more 2 seconds or more 2 seconds or more
Detection Logic 2-trip detection logic 2-trip detection logic 2-trip detection logic 2-trip detection logic

HINT:

DTC P070562 is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly, transmission control switch*1 or wire harness of their circuits.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the TCM. For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (P, R, N, D or B*2).

The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will then illuminate the MIL and store a DTC.

*1: w/ Shift Paddle Switch

*2: w/o Shift Paddle Switch

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

w/ Shift Paddle Switch:

(a)

Wait with the shift lever in each position (P, R, N or D) for 60 seconds or more with the ignition switch ON.

(b)

Wait for 2 seconds or more with the shift lever in M.


4.

w/o Shift Paddle Switch:

(a)

Wait with the shift lever in each position (P, R, N, D or B) for 60 seconds or more with the ignition switch ON.


5.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

6.

Input the DTC: P070513 or P070562.

7.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

w/ Shift Paddle Switch:
C398677E11
0.365,1.604 1.875,2.229 1.51,0.625 10 false from BKUP LP Fuse 0.354,4.083 1.646,4.698 1.292,0.615 10 false from ECU-IGR NO. 1 Fuse 2.26,3.104 3.583,3.531 1.323,0.427 10 false Park/Neutral Position Switch Assembly 2.26,2.938 2.719,3.135 0.458,0.198 10 false D45 2.021,4.677 4.063,5.24 2.042,0.563 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 2.042,4.5 2.5,4.698 0.458,0.198 10 false H64 5.74,4.719 6.198,4.917 0.458,0.198 10 false D71 5.74,4.875 6.198,5.073 0.458,0.198 10 false TCM 3.208,2.354 3.667,2.552 0.458,0.198 10 false DL 3.219,1.76 3.677,1.958 0.458,0.198 10 false NL 3.208,1.156 3.667,1.354 0.458,0.198 10 false RL 3.208,0.552 3.667,0.75 0.458,0.198 10 false PL 3.51,0.563 3.969,0.76 0.458,0.198 10 false 6 3.521,1.167 3.979,1.365 0.458,0.198 10 false 1 3.531,1.76 3.99,1.958 0.458,0.198 10 false 9 3.542,2.354 4,2.552 0.458,0.198 10 false 7 5.021,2.354 5.479,2.552 0.458,0.198 10 false 31 5,1.76 5.458,1.958 0.458,0.198 10 false 32 5.01,1.167 5.469,1.365 0.458,0.198 10 false 30 5.021,0.563 5.479,0.76 0.458,0.198 10 false 29 5.344,0.563 5.802,0.76 0.458,0.198 10 false P 5.333,1.167 5.792,1.365 0.458,0.198 10 false R 5.323,1.76 5.781,1.958 0.458,0.198 10 false N 5.323,2.365 5.781,2.563 0.458,0.198 10 false D 5.323,3.948 5.781,4.146 0.458,0.198 10 false B 5.031,3.948 5.49,4.146 0.458,0.198 10 false 14 3.5,3.948 3.958,4.146 0.458,0.198 10 false 5 3.26,3.948 3.719,4.146 0.458,0.198 10 false S 2.51,3.948 2.969,4.146 0.458,0.198 10 false IG 2.281,3.948 2.74,4.146 0.458,0.198 10 false 4 2.26,1.469 2.719,1.667 0.458,0.198 10 false 2 2.51,1.469 2.969,1.667 0.458,0.198 10 false RB

w/o Shift Paddle Switch:
C428689E03
0.104,2.563 2.25,2.76 2.146,0.198 10 false from BKUP LP Fuse 2.042,2.417 2.198,2.615 0.156,0.198 10 false 2 2.271,2.427 2.583,2.625 0.313,0.198 10 false RB 3.375,1.229 3.688,1.427 0.313,0.198 10 false PL 3.375,1.833 3.688,2.031 0.313,0.198 10 false RL 3.375,2.427 3.688,2.625 0.313,0.198 10 false NL 3.385,3.031 3.698,3.229 0.313,0.198 10 false DL 3.375,3.625 3.688,3.823 0.313,0.198 10 false 2L 2.208,4.25 2.667,4.448 0.458,0.198 10 false D45 2.198,4.427 3.594,4.875 1.396,0.448 10 false Park/Neutral Position Switch Assembly 5.594,5.063 6.156,5.542 0.563,0.479 10 false TCM 5.594,4.875 6.052,5.073 0.458,0.198 10 false D71 4.938,1.229 5.25,1.427 0.313,0.198 10 false 29 3.677,1.229 3.833,1.427 0.156,0.198 10 false 6 3.677,1.833 3.833,2.031 0.156,0.198 10 false 1 4.917,2.427 5.229,2.625 0.313,0.198 10 false 32 3.688,2.427 3.844,2.625 0.156,0.198 10 false 9 3.688,3.021 3.844,3.219 0.156,0.198 10 false 7 3.688,3.625 3.844,3.823 0.156,0.198 10 false 3 4.927,3.031 5.24,3.229 0.313,0.198 10 false 31 4.917,3.625 5.229,3.823 0.313,0.198 10 false 14 5.219,3.625 5.375,3.823 0.156,0.198 10 false B 5.219,3.031 5.375,3.229 0.156,0.198 10 false D 5.219,2.427 5.375,2.625 0.156,0.198 10 false N 4.927,1.833 5.24,2.031 0.313,0.198 10 false 30 5.208,1.833 5.365,2.031 0.156,0.198 10 false R 5.208,1.229 5.365,1.427 0.156,0.198 10 false P

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Shift Paddle Switch A
w/o Shift Paddle Switch B



A

2.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))

B

23.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))
2.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in P When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
50003 373 15
Result:
Result Proceed to
The value of Shift SW Status (P Range) is ON A
The value of Shift SW Status (P Range) is not ON B




A

3.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
50003 373 15
Result:
Result Proceed to
The value of Shift SW Status (P Range) is OFF A
The value of Shift SW Status (P Range) is not OFF B




A

4.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
4.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in R When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (R Range)
50003 373 14
Result:
Result Proceed to
The value of Shift SW Status (R Range) is ON A
The value of Shift SW Status (R Range) is not ON B




A

5.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
5.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in R When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (R Range)
50003 373 14
Result:
Result Proceed to
The value of Shift SW Status (R Range) is OFF A
The value of Shift SW Status (R Range) is not OFF B




A

6.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
6.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in N When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (N Range)
50003 373 13
Result:
Result Proceed to
The value of Shift SW Status (N Range) is ON A
The value of Shift SW Status (N Range) is not ON B




A

7.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
7.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in N When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (N Range)
50003 373 13
Result:
Result Proceed to
The value of Shift SW Status (N Range) is OFF A
The value of Shift SW Status (N Range) is not OFF B




A

8.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
8.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in D When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (D Range)
50003 373 28
Result:
Result Proceed to
The value of Shift SW Status (D Range) is ON A
The value of Shift SW Status (D Range) is not ON B




A

9.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
9.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in D When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (D Range)
50003 373 28
Result:
Result Proceed to
The value of Shift SW Status (D Range) is OFF A
The value of Shift SW Status (D Range) is not OFF B




A

10.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

B

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
10.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Transmission control switch status OFF or ON OFF: Shift lever not in M, "+" or "-" -
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (S Range)
50003 373 27
Result:
Result Proceed to
The value of Shift SW Status (S Range) is OFF A
The value of Shift SW Status (S Range) is not OFF B




A

B

11.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE))
11.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE))

Pre-procedure1

a.

Disconnect the shift lock control unit assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H64)Location & Routing

Click Connector(H64)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transmission Control Switch (Transmission Floor Shift Assembly)

H64-4 (IG) - Body ground Ignition switch ON 11 to 14 V
H64-4 (IG) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the shift lock control unit assembly connector.



OK

12.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (POWER SOURCE))

12.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

13.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

B

16.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
13.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

Pre-procedure1

a.
C239095C90
1.5,0.208 1.896,0.438 0.396,0.229 0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.906,1.802 2.375,2 0.469,0.198 10 false IG 0.646,1.771 1.021,1.979 0.375,0.208 10 false S 1.583,0.229 1.938,0.417 0.354,0.188 10 false H64
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H64)Location & Routing

Click Connector(H64)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transmission Control Switch (Transmission Floor Shift Assembly)

H64-4 (IG) - H64-5 (S) Shift lever in M, "+" or "- " Below 1 Ω
H64-4 (IG) - H64-5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the shift lock control unit assembly connector.



OK

14.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

Pre-procedure1

a.

Disconnect the shift lock control unit assembly connector.


b.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H64,D71)Location & Routing

Click Connector(H64)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transmission Control Switch (Transmission Floor Shift Assembly)

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

H64-5 (S) - D71-14 (B) Always Below 1 Ω
H64-5 (S) or D71-14 (B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.


b.

Connect the shift lock control unit assembly connector.



OK

15.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

15.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

Pre-procedure1

a.
C239095C90
1.5,0.208 1.896,0.438 0.396,0.229 0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.906,1.802 2.375,2 0.469,0.198 10 false IG 0.646,1.771 1.021,1.979 0.375,0.208 10 false S 1.583,0.229 1.938,0.417 0.354,0.188 10 false H64
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H64)Location & Routing

Click Connector(H64)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transmission Control Switch (Transmission Floor Shift Assembly)

H64-4 (IG) - H64-5 (S) Shift lever in M, "+" or "- " Below 1 Ω
H64-4 (IG) - H64-5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the shift lock control unit assembly connector.



OK

17.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

Pre-procedure1

a.

Disconnect the shift lock control unit assembly connector.


b.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H64,D71)Location & Routing

Click Connector(H64)Instrument Panel>Instrument Panel Wire / Speaker Wire>Transmission Control Switch (Transmission Floor Shift Assembly)

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

H64-5 (S) - D71-14 (B) Always Below 1 Ω
H64-5 (S) or D71-14 (B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.


b.

Connect the shift lock control unit assembly connector.



OK

18.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - TCM)

18.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the park/neutral position switch assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D45)Location & Routing

Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assembly

D45-2 (RB) - Body ground Ignition switch ON 11 to 14 V
D45-2 (RB) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the park/neutral position switch assembly connector.



OK

20.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

20.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Pre-procedure1

a.
C193931C61
0.177,1.01 0.594,1.271 0.417,0.26 2.167,0.25 1.833,0.25 1.833,0.25 1.625,0.938 true 2.583,0.5 2.333,0.5 2.333,0.5 2.042,1 true 2.167,2 1.917,2 1.917,2 1.792,1.479 true 0.833,1.833 1.083,1.833 1.083,1.833 1.24,1.469 true 2.688,1.833 2.438,1.833 2.438,1.833 2.135,1.49 true 2.219,0.156 2.583,0.396 0.365,0.24 10 false RB 2.635,0.406 2.958,0.604 0.323,0.198 10 false RL 0.635,1.75 1.104,1.938 0.469,0.188 10 false NL 2.219,1.927 2.74,2.094 0.521,0.167 10 false DL 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a 2.729,1.75 3.25,1.917 0.521,0.167 10 false PL 0.26,1.063 0.583,1.26 0.323,0.198 10 false D45
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D45)Location & Routing

Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assembly

D45-2 (RB) - D45-6 (PL) Shift lever in P Below 1 Ω
D45-2 (RB) - D45-6 (PL) Shift lever not in P 10 kΩ or higher
D45-2 (RB) - D45-1 (RL) Shift lever in R Below 1 Ω
D45-2 (RB) - D45-1 (RL) Shift lever not in R 10 kΩ or higher
D45-2 (RB) - D45-9 (NL) Shift lever in N Below 1 Ω
D45-2 (RB) - D45-9 (NL) Shift lever not in N 10 kΩ or higher
D45-2 (RB) - D45-7 (DL) Shift lever in D, M, "+" or "-" Below 1 Ω
D45-2 (RB) - D45-7 (DL) Shift lever not in D, M, "+" or "-" 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the park/neutral position switch assembly connector.



OK

21.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

Pre-procedure1

a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D45,D71)Location & Routing

Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assembly

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D45-6 (PL) - D71-29 (P) Always Below 1 Ω
D45-1 (RL) - D71-30 (R) Always Below 1 Ω
D45-9 (NL) - D71-32 (N) Always Below 1 Ω
D45-7 (DL) - D71-31 (D) Always Below 1 Ω
D45-6 (PL) or D71-29 (P) - Body ground and other terminals Always 10 kΩ or higher
D45-1 (RL) or D71-30 (R) - Body ground and other terminals Always 10 kΩ or higher
D45-9 (NL) or D71-32 (N) - Body ground and other terminals Always 10 kΩ or higher
D45-7 (DL) or D71-31 (D) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.


b.

Connect the park/neutral position switch assembly connector.



OK

22.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

22.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in P When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
50003 373 15
Result:
Result Proceed to
The value of Shift SW Status (P Range) is ON A
The value of Shift SW Status (P Range) is not ON B




A

24.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
24.READ VALUE USING GTS (SHIFT SW STATUS (P RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
50003 373 15
Result:
Result Proceed to
The value of Shift SW Status (P Range) is OFF A
The value of Shift SW Status (P Range) is not OFF B




A

25.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
25.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in R When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (R Range)
50003 373 14
Result:
Result Proceed to
The value of Shift SW Status (R Range) is ON A
The value of Shift SW Status (R Range) is not ON B




A

26.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
26.READ VALUE USING GTS (SHIFT SW STATUS (R RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in R When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (R Range)
50003 373 14
Result:
Result Proceed to
The value of Shift SW Status (R Range) is OFF A
The value of Shift SW Status (R Range) is not OFF B




A

27.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
27.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in N When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (N Range)
50003 373 13
Result:
Result Proceed to
The value of Shift SW Status (N Range) is ON A
The value of Shift SW Status (N Range) is not ON B




A

28.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
28.READ VALUE USING GTS (SHIFT SW STATUS (N RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in N When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (N Range)
50003 373 13
Result:
Result Proceed to
The value of Shift SW Status (N Range) is OFF A
The value of Shift SW Status (N Range) is not OFF B




A

29.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
29.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON ON: Shift lever in D When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (D Range)
50003 373 28
Result:
Result Proceed to
The value of Shift SW Status (D Range) is ON A
The value of Shift SW Status (D Range) is not ON B




A

30.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
30.READ VALUE USING GTS (SHIFT SW STATUS (D RANGE))
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in D When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (D Range)
50003 373 28
Result:
Result Proceed to
The value of Shift SW Status (D Range) is OFF A
The value of Shift SW Status (D Range) is not OFF B




A

B

31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
31.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the park/neutral position switch assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D45)Location & Routing

Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assembly

D45-2 (RB) - Body ground Ignition switch ON 11 to 14 V
D45-2 (RB) - Body ground Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the park/neutral position switch assembly connector.



OK

32.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

32.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Pre-procedure1

a.
C193931C60
0.156,1.083 0.604,1.333 0.448,0.25 2.167,0.25 1.833,0.25 1.833,0.25 1.625,0.938 true 2.667,0.5 2.417,0.5 2.417,0.5 2.042,1 true 2.167,2 1.917,2 1.917,2 1.792,1.479 true 0.833,1.833 1.083,1.833 1.083,1.833 1.24,1.469 true 2.667,1.833 2.438,1.833 2.438,1.833 2.135,1.49 true 1.323,1 1.083,0.5 1.083,0.5 0.833,0.5 true 2.219,0.156 2.583,0.396 0.365,0.24 10 false RB 2.75,0.417 3.073,0.615 0.323,0.198 10 false RL 0.635,1.75 1.104,1.938 0.469,0.188 10 false NL 2.219,1.927 2.74,2.094 0.521,0.167 10 false DL 0.104,0.073 0.281,0.271 0.177,0.198 10 false *a 2.729,1.75 3.25,1.917 0.521,0.167 10 false PL 0.667,0.417 0.979,0.615 0.313,0.198 10 false 2L 0.25,1.146 0.573,1.313 0.323,0.167 10 false D45
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D45)Location & Routing

Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assembly

D45-2 (RB) - D45-6 (PL) Shift lever in P Below 1 Ω
D45-2 (RB) - D45-6 (PL) Shift lever not in P 10 kΩ or higher
D45-2 (RB) - D45-1 (RL) Shift lever in R Below 1 Ω
D45-2 (RB) - D45-1 (RL) Shift lever not in R 10 kΩ or higher
D45-2 (RB) - D45-9 (NL) Shift lever in N Below 1 Ω
D45-2 (RB) - D45-9 (NL) Shift lever not in N 10 kΩ or higher
D45-2 (RB) - D45-7 (DL) Shift lever in D Below 1 Ω
D45-2 (RB) - D45-7 (DL) Shift lever not in D 10 kΩ or higher
D45-2 (RB) - D45-3 (2L) Shift lever in B Below 1 Ω
D45-2 (RB) - D45-3 (2L) Shift lever not in B 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the park/neutral position switch assembly connector.



OK

33.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

33.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

Pre-procedure1

a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the TCM connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D45,D71)Location & Routing

Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assembly

Click Connector(D71)Engine Compartment>Engine Wire>Transmission Control ECU

D45-6 (PL) - D71-29 (P) Always Below 1 Ω
D45-1 (RL) - D71-30 (R) Always Below 1 Ω
D45-9 (NL) - D71-32 (N) Always Below 1 Ω
D45-7 (DL) - D71-31 (D) Always Below 1 Ω
D45-3 (2L) - D71-14 (B) Always Below 1 Ω
D45-6 (PL) or D71-29 (P) - Body ground and other terminals Always 10 kΩ or higher
D45-1 (RL) or D71-30 (R) - Body ground and other terminals Always 10 kΩ or higher
D45-9 (NL) or D71-32 (N) - Body ground and other terminals Always 10 kΩ or higher
D45-7 (DL) or D71-31 (D) - Body ground and other terminals Always 10 kΩ or higher
D45-3 (2L) or D71-14 (B) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Connect the TCM connector.


b.

Connect the park/neutral position switch assembly connector.



OK

34.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

34.REPLACE TCM
HINT:

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>TCM>REMOVAL


Result:
Proceed to
NEXT



NEXT