Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY › from 2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441196 HV RELAY ASSEMBLY A

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A472777N08
4.344,3.344 4.052,3.344 false 1.521,0.323 1.844,0.323 false 3.396,0.635 3.708,0.635 false 6.552,0.188 6.865,0.188 false 3.896,3.188 4.177,3.542 0.281,0.354 18 false 2 1.083,0.167 1.74,0.51 0.656,0.344 18 false 3, 7 6.031,0.063 6.948,0.521 0.917,0.458 18 false 1, 5 4.167,0.479 4.823,0.823 0.656,0.344 18 false 4, 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SERVICE PLUG GRIP G3834 - - -
3 DISCONNECT ENGINE WIRE 82121 (Click here) - -
4 CONNECTOR COVER ASSEMBLY - (Click here) - -
5 TERMINAL VOLTAGE - (Click here) - -
6 CONNECTOR COVER ASSEMBLY - (Click here) - -
7 CONNECT ENGINE WIRE 82121 (Click here) - -

A461204N05
1.354,1.344 2.875,1.344 false 2.719,2.125 2.719,1.344 false 5.385,0.688 5.75,0.688 false 5.302,1.677 5.938,1.677 false 2.615,4.156 3.042,4.156 false 6.115,3.948 6.542,3.948 false 3.156,1.208 3.708,1.563 0.552,0.354 18 false 10 6.104,1.5 6.656,1.854 0.552,0.354 18 false 9 6.604,3.771 7.156,4.125 0.552,0.354 18 false 12 3.104,4 3.656,4.354 0.552,0.354 18 false 11 6.135,3.438 6.375,3.635 0.24,0.198 10 false x6 2.99,1.271 3.354,1.5 0.365,0.229 10 false ● 5.875,0.542 6.427,0.896 0.552,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

8 REAR CENTER SEAT OUTER BELT ASSEMBLY 73350C - - -
9 BENCH TYPE REAR SEAT CUSHION ASSEMBLY - - - -
10 REAR SEAT CUSHION LOCK HOOK 72693 - - -
11 REAR UNDER COVER 76971G - - -
12 REAR SEAT CUSHION LEG SUB-ASSEMBLY 71033 - - -

● Non-reusable part - -

A478810N01
2.5,4.99 2.5,5.167 false 5.458,2.792 5.458,3 false 5.385,5.25 5.635,5.25 false 2.375,2.5 2.708,2.5 false 4.146,0.938 4.479,0.938 false 2.813,1.542 3.146,1.542 false 4.083,1.958 4.083,2.167 false 2.583,5.198 3.135,5.552 0.552,0.354 18 false 13 5.573,3.073 6.125,3.427 0.552,0.354 18 false 14 5.979,5.104 6.531,5.458 0.552,0.354 18 false 15 2.792,2.354 3.344,2.708 0.552,0.354 18 false 16 4.906,0.823 5.458,1.177 0.552,0.354 18 false 17 2.479,1.396 3.031,1.75 0.552,0.354 18 false 18 4.104,2.167 4.656,2.521 0.552,0.354 18 false 18 4.219,1.458 4.531,1.656 0.313,0.198 10 false x4 1.958,1.74 2.271,1.938 0.313,0.198 10 false x4 0.458,2.677 0.771,2.875 0.313,0.198 10 false x6 2.208,4.229 2.521,4.427 0.313,0.198 10 false x5

Procedure Part Name Code
Z101186

Z101188

Z101187

13 HV BATTERY UPPER COVER PANEL G92N1 (Click here) - -
14 HV FLOOR UNDER WIRE 821H1 (Click here) - -
15 FLOOR WIRE 82161 (Click here) - -
16 UPPER HV BATTERY COVER SUB-ASSEMBLY - - - -
17 ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY G3830A (Click here) - -
18 NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY G3850 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Replacement of HV battery junction block assembly Current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 82121 3.DISCONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 4.REMOVE CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 5.CHECK TERMINAL VOLTAGE

Z101186

Click here(Click here)

Hide 6.INSTALL CONNECTOR COVER ASSEMBLY

Z101186

Click here(Click here)

Hide 82121 7.CONNECT ENGINE WIRE

Z101186

Click here(Click here)

Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 76971G 11.REMOVE REAR UNDER COVER

Hide 71033 12.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N1 13.REMOVE HV BATTERY UPPER COVER PANEL

Z101186

Click here(Click here)

Hide 821H1 14.DISCONNECT FLOOR UNDER WIRE

Z101186

Click here(Click here)

Hide 82161 15.DISCONNECT FLOOR WIRE

Z101186

Click here(Click here)

Hide 16.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide G3830A 17.REMOVE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A461189E01
0.552,0.135 0.74,0.427 0.188,0.292 18 true i 4.271,1.313 4.458,1.604 0.188,0.292 18 true ii 6.094,1.313 6.302,1.615 0.208,0.302 18 true iii 0.563,1.979 0.792,2.281 0.229,0.302 18 true iv 3.844,2.052 4.073,2.354 0.229,0.302 18 true v

i.

Disengage the claw and open the wiring harness protector.


ii.

Disconnect the No. 1 traction battery device box assembly connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



iii.

Disconnect the hybrid battery terminal block connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



iv.

Remove the bolt and electric vehicle battery plug assembly from the HV battery.


v.

Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the wiring harness protector.



Hide G3850 18.REMOVE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A458363N01
1.781,0.698 2.063,1.052 0.281,0.354 18 false i 0.573,0.083 0.771,0.365 0.198,0.281 18 true i 3.927,0.083 4.125,0.365 0.198,0.281 18 true ii

i.

Disconnect the 2 No. 1 traction battery device box assembly connectors.

NOTICE:

Insulate the disconnected high-voltage connectors with insulating tape.



ii.

Remove the 4 nuts and No. 1 traction battery device box assembly from the No. 1 hybrid battery shield sub-assembly.

NOTICE:

If the No. 1 traction battery device box assembly has been struck or dropped, replace it with a new one.