Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY STACK › from 2021.07
RM3700E _51 Engine / Hybrid System _093506 HYBRID / BATTERY CONTROL _0441203 HV BATTERY STACK A

HYBRID / BATTERY CONTROL  HV BATTERY STACK  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A461527N04
1.583,2.198 1.854,2.198 false 1.719,3.552 1.969,3.552 false 3.583,2.813 3.583,2.979 false 4.583,2.792 4.417,2.792 4.417,2.792 4.344,3.042 false 6.229,5.208 6.385,5.208 false 2.063,5.25 2.396,5.25 false 5.979,3.167 6.146,3.167 false 5.969,1.708 6.177,1.708 false 6.406,0.24 6.74,0.24 false 4.385,0.865 4.719,0.865 false 2.25,2.073 2.531,2.427 0.281,0.354 18 false 9 2.302,3.417 2.667,3.771 0.365,0.354 18 false 11 3.615,2.979 3.896,3.333 0.281,0.354 18 false 5 4.906,2.646 5.188,3 0.281,0.354 18 false 7 6.719,5.104 7,5.458 0.281,0.354 18 false 8 2.438,5.125 2.719,5.479 0.281,0.354 18 false 3 6.5,3.063 6.917,3.417 0.417,0.354 18 false 10 6.542,1.604 6.823,1.958 0.281,0.354 18 false 6 5.896,0.094 6.677,0.563 0.781,0.469 18 false 1, 2 4.771,0.719 5.052,1.073 0.281,0.354 18 false 4 2.5,1.292 2.781,1.563 0.281,0.271 10 false x6 1.271,3.146 1.552,3.417 0.281,0.271 10 false x3 5.792,1.125 6.073,1.396 0.281,0.271 10 false x4 5.99,2.542 6.271,2.813 0.281,0.271 10 false x2 4.125,0.271 4.406,0.542 0.281,0.271 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 READ VALUE USING GTS - (Click here) - -
3 HV SUPPLY BATTERY ASSEMBLY G9510 - - -
4 UPPER HV BATTERY COVER SUB-ASSEMBLY - - - -
5 ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY G3830A (Click here) - -
6 NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY G3850 (Click here) - -
7 HYBRID BATTERY TERMINAL BLOCK G92Z2 (Click here) - -
8 NO. 1 HYBRID BATTERY INTAKE DUCT G92E1A (Click here) - -
9 NO. 1 HV BATTERY HOSE G929A (Click here) - -
10 NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY G920Q (Click here) - -
11 BATTERY ECU ASSEMBLY 89890A (Click here) - -

A461528N02
4.083,1.333 4.25,1.333 4.25,1.333 4.375,1.052 false 5.896,1.052 5.896,0.927 false 6.448,0.219 6.781,0.219 false 0.979,1.24 1.344,1.24 false 5.938,1.115 6.271,1.615 0.333,0.5 18 false 12 6.125,0.104 6.458,0.604 0.333,0.5 18 false 15 5.177,0.333 5.427,0.583 0.25,0.25 10 false x4 3.75,1.208 4.083,1.708 0.333,0.5 18 false 14 2.823,0.969 3.073,1.219 0.25,0.25 10 false x4 0.667,1.115 1,1.615 0.333,0.5 18 false 13

Procedure Part Name Code
Z101186

Z101188

Z101187

12 NO. 1 HV BATTERY PROTECTOR G92PC (Click here) - -
13 NO. 2 HV SUPPLY STACK SUB-ASSEMBLY G9509 (Click here) - -
14 NO. 1 HV SUPPLY STACK SUB-ASSEMBLY G9508 (Click here) - -
15 PERFORM RECOVERY INSPECTION - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV supply stack sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
·

Replacement of No. 1 HV supply stack sub-assembly

·

Replacement of No. 2 HV supply stack sub-assembly


1.

Prediagnostic Battery Charge

2.

Battery Diagnosis

3.

Battery Status Info Update


HV battery status information cannot be updated (Click here)
·

Replacement of battery ECU assembly

·

Replacement of HV battery junction block assembly


Current sensor offset learning DTCs are stored (Click here)
Replacement of hybrid battery terminal block Perform high voltage fuse accumulated load history reset (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

·

The hybrid system has high-voltage circuits. Accidents, such as electric shock, or electric leaks may result if the hybrid system is not operated in a correct manner. Make sure to follow the correct procedure.

·

When disposing of an HV battery assembly or hybrid vehicle supply stack sub-assembly, make sure to return them through an authorized collection agent who is capable of handling them safely.

·

Before returning an HV battery assembly, make sure to perform a recovery inspection.

·

Before returning an HV supply stack sub-assembly, make sure to perform a recovery inspection.

·

Make a note of the output DTCs as some of them may be necessary for "Recovery Inspection" of the HV battery assembly and HV supply stack sub-assemblies.



NOTICE:

When replacing the No. 1 hybrid vehicle supply stack sub-assembly or No. 2 hybrid vehicle supply stack sub-assembly, it is necessary to check, adjust and equalize the SOC of the HV battery. Otherwise, the engine may run longer than normal, resulting in a decrease in fuel efficiency.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>BASIC INSPECTION


HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2. READ VALUE USING GTS

a.
A461168N08
0.5,0.094 1.719,0.469 1.219,0.375 18 false i, ii, iii, iv

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid/EV Battery Temperature 1 to 6.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Temperature 1
Hybrid/EV Battery Temperature 2
Hybrid/EV Battery Temperature 3
Hybrid/EV Battery Temperature 4
Hybrid/EV Battery Temperature 5
Hybrid/EV Battery Temperature 6
50003 398 62,63,64,65,66,67

iv.

Read the Data List.

NOTICE:

If any of the temperatures listed in "Hybrid/EV Battery Temperature 1 to 6" are 50°C or more, leave the vehicle until the temperature drops to less than 50°C.




Hide G9510 3.REMOVE HV SUPPLY BATTERY ASSEMBLY

Hide 4.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide G3830A 5.REMOVE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

Z101186

Click here(Click here)

Hide G3850 6.REMOVE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

Z101186

Click here(Click here)

Hide G92Z2 7.REMOVE HYBRID BATTERY TERMINAL BLOCK

Z101186

Click here(Click here)

Hide G92E1A 8.REMOVE NO. 1 HYBRID BATTERY INTAKE DUCT

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A459146


Hide G929A 9.REMOVE NO. 1 HV BATTERY HOSE

Z101186

Click here(Click here)

Hide G920Q 10.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A460060


Hide 89890A 11.REMOVE BATTERY ECU ASSEMBLY

Z101186

Click here(Click here)

Hide G92PC 12.REMOVE NO. 1 HV BATTERY PROTECTOR

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A459149


Hide G9509 13.REMOVE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.


NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



a.
A461193


Hide G9508 14.REMOVE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

Z101186

CAUTION:

Be sure to wear insulated gloves and protective goggles.



a.
A461194


Hide 15.PERFORM RECOVERY INSPECTION

a.
A461169N02
1.417,0.167 1.698,0.521 0.281,0.354 18 false i

i.

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION