Home › Power Source / Network › POWER DISTRIBUTION › FUSIBLE LINK (for 120A DC/DC) › from 2021.07
RM3700E _57 Power Source / Network _093028 POWER DISTRIBUTION _0502152 FUSIBLE LINK(for 120A DC/DC) A

POWER DISTRIBUTION  FUSIBLE LINK(for 120A DC/DC)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E471055N01
1.948,2.51 1.948,2.177 false 3.385,0.865 3.052,0.865 false 5.656,0.583 5.323,0.583 false 1.875,2.531 2.156,2.885 0.281,0.354 18 false 1 2.875,0.698 3.156,1.052 0.281,0.354 18 false 2 5.729,0.427 6.01,0.781 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE - - - -
2 ECM 89661 - - -
3 NO. 1 RELAY BLOCK COVER 82662A - - -

E471056N01
0.896,0.917 1.229,0.917 false 2.042,0.458 2.208,0.458 2.208,0.458 2.375,0.833 false 5,0.583 5.333,0.583 false 3.531,0.552 3.865,0.552 false 3.344,0.406 3.625,0.76 0.281,0.354 18 false 4 5.396,0.417 5.677,0.771 0.281,0.354 18 false 5 1.844,0.292 2.125,0.646 0.281,0.354 18 false 6 0.708,0.75 0.99,1.104 0.281,0.354 18 false 7

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 1 IGNITION RELAY 28371 - - -
5 WINDSHIELD WIPER RELAY 85948 - - -
6 VVT RELAY 85912K - - -
7 SECURITY WARNING RELAY 89730A - - -

E471057N02
4.813,0.115 7,1.594 2.188,1.479 1.125,0.344 1.458,0.344 false 1.406,1.385 1.74,1.385 false 4.031,1.417 4.365,1.417 false 5.802,1.313 5.802,0.979 false 4.208,3.844 4.458,3.844 false 1.229,2.354 1.563,2.354 false 1.188,2.979 1.521,2.979 false 1.865,4.99 2.115,4.99 false 5.417,5.115 5.417,4.781 false 3.51,2.885 3.844,2.885 false 2.448,4.875 2.729,5.229 0.281,0.354 18 false 8 4.781,3.698 5.063,4.052 0.281,0.354 18 false 9 3.885,2.719 4.344,3.063 0.458,0.344 18 false 10 5.354,5.177 5.667,5.354 0.313,0.177 10 false *1 4.427,1.333 4.708,1.521 0.281,0.188 10 false *2 0.844,2.271 1.365,2.458 0.521,0.188 10 false ● *3 5.729,1.344 6.042,1.521 0.313,0.177 10 false *1 1,2.906 1.313,3.083 0.313,0.177 10 false *1 1.802,1.302 2.115,1.479 0.313,0.177 10 false *1 1.521,0.271 1.833,0.448 0.313,0.177 10 false *1 4.875,0.167 5.25,0.406 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

8 RELAY BLOCK LOWER COVER 82663 (Click here) - -
9 FUSE BLOCK ASSEMBLY 82610A (Click here) - -
10 ENGINE ROOM FUSIBLE LINK 82210P - - -

*A for RHD - -
*1 WIRE HARNESS *2 ENGINE ROOM RELAY BLOCK
*3 WIRE HARNESS REPAIR TAPE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the engine room fusible link removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 82662A 3.REMOVE NO. 1 RELAY BLOCK COVER

Hide 28371 4.REMOVE NO. 1 IGNITION RELAY

a.
E471030


Hide 85948 5.REMOVE WINDSHIELD WIPER RELAY

a.
E471031


Hide 85912K 6.REMOVE VVT RELAY

a.
E471032


Hide 89730A 7.REMOVE SECURITY WARNING RELAY

a.
E471033


Hide 82663 8.REMOVE RELAY BLOCK LOWER COVER

a.
E471034N01
1.927,0.073 2.208,0.427 0.281,0.354 18 false i

i.

Remove the nut.



b.
E471035N01
1.958,0.073 2.24,0.427 0.281,0.354 18 false i

i.

Disconnect the 2 connectors.



c.
E471036C02
1.823,0.063 2.104,0.417 0.281,0.354 18 false i
V113147

Separate in this Direction - -


i.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness as shown in the illustration.



d.
E471037N01
1.938,0.073 2.219,0.427 0.281,0.354 18 false i

i.

for RHD:

1. Disengage the clamps.



e.
E471038N01
1.938,0.073 2.219,0.427 0.281,0.354 18 false i

i.

Remove the 2 bolts and nut.



f.
E471039C02
4.031,0.708 4.531,0.542 true 4.552,0.448 4.813,0.646 0.26,0.198 10 true *1 1.969,0.042 2.25,0.396 0.281,0.354 18 false i
*1 Engine Room Relay Block Assembly - -


i.

Disengage the guides to separate the engine room relay block assembly.



g.
E471040N01
1.854,0.094 2.135,0.448 0.281,0.354 18 false i

i.

Disengage the clamp to separate the wire harness.



h.
E473586N01
1.844,0.125 2.125,0.479 0.281,0.354 18 false i

i.

Apply protective tape to the engine room relay block as shown in the illustration.



i.
E471042N01
1.958,0.063 2.24,0.417 0.281,0.354 18 false i

i.

Remove the wire harness repair tapes.



j.
E471043N01
1.917,0.052 2.198,0.406 0.281,0.354 18 false i

i.

Disengage the claws to separate the relay block lower cover.



k.
E471044N01
1.792,0.094 2.073,0.448 0.281,0.354 18 false i

i.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws to remove the relay block lower cover.



Hide 82610A 9.SEPARATE FUSE BLOCK ASSEMBLY

a.
E471045C01
1.781,0.104 2.063,0.458 0.281,0.354 18 false i
V113147

Separate in this Direction - -


i.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the wire harness as shown in the illustration.



b.
E471046N01
1.958,0.063 2.24,0.417 0.281,0.354 18 false i

i.

Remove the vinyl tape.



c.
E471048C02
1.885,0.063 2.167,0.417 0.281,0.354 18 false i
V113147

Move in this Direction - -


i.

Move the engine room relay block as shown in the illustration.



d.
E471048C03
1.885,0.063 2.167,0.417 0.281,0.354 18 false i
V113147

Separate in this Direction - -


i.

Using a screwdriver with its tip wrapped in protective tape, disengage the claws to separate the fuse block assembly as shown in the illustration.



Hide 82210P 10.REMOVE ENGINE ROOM FUSIBLE LINK

a.
E471049C02
0,0 0,0 false
V113147

Remove in this Direction - -