Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is stored, check the No. 1 ignition coil (No. 1 cylinder) circuit.

·

If DTC P0352 is stored, check the No. 1 ignition coil (No. 2 cylinder) circuit.

·

If DTC P0353 is stored, check the No. 1 ignition coil (No. 3 cylinder) circuit.

·

If DTC P0354 is stored, check the No. 1 ignition coil (No. 4 cylinder) circuit.



A direct ignition system is used on this vehicle.

The direct ignition system is an ignition system in which each cylinder is ignited by its own No. 1 ignition coil and spark plug. The secondary wiring of each No. 1 ignition coil generates a powerful voltage which is applied directly to each spark plug. The spark passes from the center electrode of the spark plug to the ground electrode.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A256693E03
3.855,0.87 4.463,1.022 0.607,0.152 10 Igniter 4.427,1.401 4.374,0.957 4.374,0.957 4.304,0.957 false 4.514,0.555 5.329,0.735 0.816,0.180 10 from Battery 5.393,1.157 5.561,0.81 5.561,0.81 5.638,0.81 false 5.666,0.733 6.829,1.288 1.163,0.555 10 No. 1 Ignition Coil (No. 1 Cylinder) 5.603,1.865 6.717,2.041 1.114,0.177 10 No. 1 Spark Plug 5.617,3.101 6.731,3.278 1.114,0.177 10 No. 2 Spark Plug 5.621,4.425 6.735,4.602 1.114,0.177 10 No. 3 Spark Plug 5.624,5.724 6.738,5.901 1.114,0.177 10 No. 4 Spark Plug 2.731,0.579 3.078,0.759 0.347,0.180 10 ECM 2.88,1.467 3.241,1.623 0.361,0.156 10 IGT1 2.875,1.759 3.246,1.908 0.371,0.149 10 IGF1 0.307,1.437 2.037,1.606 1.730,0.169 10 Crankshaft Position Sensor 0.314,3.238 2.044,3.406 1.730,0.169 10 Camshaft Position Sensor 2.869,2.784 3.230,2.940 0.361,0.156 10 IGT2 2.873,5.428 3.234,5.584 0.361,0.156 10 IGT4 2.869,4.129 3.230,4.285 0.361,0.156 10 IGT3 2.7,5.749 3.116,5.898 0.416,0.149 10 TACH 0.188,4.46 2.151,5.286 1.963,0.826 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 1.897,6.131 2.828,6.269 0.930,0.139 10 to DLC3 3.733,3.372 5.997,3.603 2.265,0.231 10 No. 1 Ignition Coil (No. 2 Cylinder) 3.733,5.978 6.016,6.209 2.283,0.231 10 No. 1 Ignition Coil (No. 4 Cylinder) 3.733,4.67 5.951,4.901 2.218,0.231 10 No. 1 Ignition Coil (No. 3 Cylinder)

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
·

Ignition system

·

Open or short in IGF1 or IGT (1 to 4) circuit between No. 1 ignition coil and ECM

·

No. 1 ignition coil (No.1 to No. 4 cylinder)

·

ECM



A369820E01
2.719,0.125 3.354,0.323 0.635,0.198 10 false 5 V/DIV. 2.844,0.938 3.229,1.115 0.385,0.177 10 false GND 2.854,1.375 3.24,1.552 0.385,0.177 10 false GND 0.292,0.865 0.635,1.26 0.344,0.396 10 false CH1 (IGT) 0.292,1.281 0.635,1.677 0.344,0.396 10 false CH2 (IGF) 1.333,1.875 2.427,2.073 1.094,0.198 10 false 20 ms./DIV.


Reference: Inspection using an oscilloscope

While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E14
1.782,1.645 2.181,1.818 0.399,0.173 10 ECM 2.956,1.3 3.225,1.485 0.269,0.185 10 IGT 2.949,1.726 3.226,1.886 0.278,0.160 10 IGF 4.153,1.509 4.594,1.655 0.441,0.145 10 Igniter 5.4,1.348 6.167,1.521 0.767,0.173 10 Ignition Coil 4.539,2.35 5.968,2.540 1.430,0.191 10 No. 1 Ignition Coil 0.213,3.113 1.146,3.443 0.934,0.330 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.731 0.489,0.191 10 Normal 1.383,3.947 2.150,4.138 0.767,0.191 10 Malfunction 0.185,3.891 1.153,4.408 0.968,0.517 10 Ignition Confirmation Signal (IGF) 3.631,4.507 4.482,4.684 0.850,0.177 10 Circuit Open 5.95,4.97 6.314,5.167 0.364,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) No. 1 ignition coil
Required Sensors/Components (Related) ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read DTCs.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353 or P0354.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A254087E08
0.594,7.063 1.208,7.281 0.615,0.219 10 false Battery 0.417,6.5 0.813,6.708 0.396,0.208 10 false MAIN 0.396,5.906 0.698,6.135 0.302,0.229 10 false R/I 1.063,6.115 2.677,6.302 1.615,0.188 10 false No. 1 Integration Relay 1.479,5.823 1.802,6 0.323,0.177 10 false IG2 2.094,5.646 2.51,5.833 0.417,0.188 10 false IGN 0.844,5.5 1.125,5.688 0.281,0.188 10 false 1C 0.896,5.302 1,5.479 0.104,0.177 10 false 1 0.844,5.021 1.115,5.208 0.271,0.188 10 false 1E 0.844,4.823 1.104,5 0.26,0.177 10 false 10 2.542,4.49 2.813,4.688 0.271,0.198 10 false 1D 2.635,5.51 2.927,5.708 0.292,0.198 10 false 1E 2.24,4.49 2.427,4.656 0.188,0.167 10 false 17 2.698,5.313 2.802,5.458 0.104,0.146 10 false 2 0.771,3.688 2.406,3.938 1.635,0.25 10 false Ignition Switch Assembly 4.323,2.375 4.677,2.573 0.354,0.198 10 false IGT2 0.781,3.552 1.104,3.729 0.323,0.177 10 false F13 3.75,1.417 4.073,1.594 0.323,0.177 10 false B13 3.75,1.573 4.938,1.948 1.188,0.375 10 false No. 1 Ignition Coil (No. 1 Cylinder) 3.75,3.156 4.927,3.552 1.177,0.396 10 false No. 1 Ignition Coil (No. 2 Cylinder) 3.76,4.698 4.906,5.083 1.146,0.385 10 false No. 1 Ignition Coil (No. 3 Cylinder) 3.75,6.417 4.917,6.792 1.167,0.375 10 false No. 1 Ignition Coil (No. 4 Cylinder) 3.75,3.01 4.125,3.229 0.375,0.219 10 false B15 3.75,4.521 4.125,4.729 0.375,0.208 10 false B17 3.75,6.26 4.094,6.479 0.344,0.219 10 false B19 5.76,5.917 6.094,6.073 0.333,0.156 10 false IGF1 4.448,5.948 4.719,6.104 0.271,0.156 10 false IGF 4.417,4.229 4.688,4.385 0.271,0.156 10 false IGF 4.396,2.729 4.698,2.885 0.302,0.156 10 false IGF 4.385,1.135 4.688,1.292 0.302,0.156 10 false IGF 5.76,0.719 6.156,0.906 0.396,0.188 10 false IGT1 4.344,5.51 4.708,5.688 0.365,0.177 10 false IGT4 4.344,3.885 4.698,4.073 0.354,0.188 10 false IGT3 4.354,0.781 4.729,0.948 0.375,0.167 10 false IGT1 3.875,5.5 4.094,5.677 0.219,0.177 10 false +B 3.875,3.927 4.094,4.104 0.219,0.177 10 false +B 3.875,2.417 4.094,2.594 0.219,0.177 10 false +B 3.875,0.813 4.094,0.99 0.219,0.177 10 false +B 3.875,5.948 4.229,6.094 0.354,0.146 10 false GND 3.865,4.24 4.219,4.417 0.354,0.177 10 false GND 3.875,2.719 4.208,2.906 0.333,0.188 10 false GND 3.875,1.115 4.208,1.313 0.333,0.198 10 false GND 5.76,2.313 6.135,2.469 0.375,0.156 10 false IGT2 5.771,3.802 6.146,4 0.375,0.198 10 false IGT3 5.76,5.385 6.146,5.573 0.385,0.188 10 false IGT4 5.385,0.823 5.708,1.031 0.323,0.208 10 false B84 5.385,6.01 5.76,6.24 0.375,0.229 10 false B84 5.385,5.51 5.708,5.677 0.323,0.167 10 false B84 5.375,3.927 5.708,4.146 0.333,0.219 10 false B84 5.385,2.427 5.708,2.615 0.323,0.188 10 false B84 6.219,6.479 6.573,6.656 0.354,0.177 10 false ECM 3.677,0.708 3.781,0.854 0.104,0.146 10 false 1 4.74,5.406 4.896,5.604 0.156,0.198 10 false 3 3.688,1.021 3.781,1.188 0.094,0.167 10 false 4 0.813,3.094 0.927,3.24 0.115,0.146 10 false 5 2.083,3.083 2.188,3.229 0.104,0.146 10 false 6 3.698,5.406 3.802,5.552 0.104,0.146 10 false 1 3.677,3.833 3.781,3.979 0.104,0.146 10 false 1 3.688,2.26 3.792,2.406 0.104,0.146 10 false 1 4.771,5.844 4.875,6 0.104,0.156 10 false 2 4.74,4.146 4.865,4.323 0.125,0.177 10 false 2 4.75,1.031 4.854,1.188 0.104,0.156 10 false 2 4.75,2.635 4.854,2.792 0.104,0.156 10 false 2 4.75,2.323 4.896,2.479 0.146,0.156 10 false 3 4.75,3.833 4.885,3.99 0.135,0.156 10 false 3 4.75,0.719 4.885,0.865 0.135,0.146 10 false 3 3.688,2.531 3.781,2.698 0.094,0.167 10 false 4 3.688,4.125 3.781,4.292 0.094,0.167 10 false 4 3.688,5.823 3.781,5.99 0.094,0.167 10 false 4 5.448,0.625 5.635,0.792 0.188,0.167 10 false 85 5.438,2.208 5.635,2.417 0.198,0.208 10 false 84 5.427,3.719 5.667,3.927 0.24,0.208 10 false 83 5.438,5.302 5.656,5.479 0.219,0.177 10 false 82 5.458,5.771 5.646,5.938 0.188,0.167 10 false 81 0.219,3.896 0.604,4.094 0.385,0.198 10 false AM2 1.74,3.083 2.01,3.25 0.271,0.167 10 false IG2 1.01,3.094 1.417,3.302 0.406,0.208 10 false AM2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
a.

Disconnect the No. 1 ignition coil connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B13-4 (GND) - Body ground Always Below 1 Ω
B15-4 (GND) - Body ground Always Below 1 Ω
B17-4 (GND) - Body ground Always Below 1 Ω
B19-4 (GND) - Body ground Always Below 1 Ω




OK

2.CHECK NO. 1 IGNITION COIL (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK NO. 1 IGNITION COIL (POWER SOURCE)
a.
U126245E01
0.146,0.082 0.406,0.263 0.260,0.181 10 *a 0.415,0.519 0.722,0.700 0.306,0.181 10 B13 0.415,0.843 0.722,1.024 0.306,0.181 10 B15 0.415,1.167 0.722,1.348 0.306,0.181 10 B17 0.415,1.49 0.722,1.672 0.306,0.181 10 B19 1.865,1.732 2.220,1.897 0.355,0.165 10 GND 1.229,1.732 1.459,1.897 0.230,0.165 10 +B 2.058,1.176 2.058,1.703 false 1.371,1.176 1.371,1.703 false

Disconnect the No. 1 ignition coil connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B13-1 (+B) - B13-4 (GND) Ignition switch ON 11 to 14 V
B15-1 (+B) - B15-4 (GND) Ignition switch ON 11 to 14 V
B17-1 (+B) - B17-4 (GND) Ignition switch ON 11 to 14 V
B19-1 (+B) - B19-4 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Ignition Coil)



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
a.

Disconnect the No. 1 ignition coil connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B13-2 (IGF) - B84-81 (IGF1) Always Below 1 Ω
B15-2 (IGF) - B84-81 (IGF1) Always Below 1 Ω
B17-2 (IGF) - B84-81 (IGF1) Always Below 1 Ω
B19-2 (IGF) - B84-81 (IGF1) Always Below 1 Ω
B13-3 (IGT1) - B84-85 (IGT1) Always Below 1 Ω
B15-3 (IGT2) - B84-84 (IGT2) Always Below 1 Ω
B17-3 (IGT3) - B84-83 (IGT3) Always Below 1 Ω
B19-3 (IGT4) - B84-82 (IGT4) Always Below 1 Ω
B13-2 (IGF), B15-2 (IGF), B17-2 (IGF), B19-2 (IGF) or B84-81 (IGF1) - Body ground Always 10 kΩ or higher
B13-3 (IGT1) or B84-85 (IGT1) - Body ground Always 10 kΩ or higher
B15-3 (IGT2) or B84-84 (IGT2) - Body ground Always 10 kΩ or higher
B17-3 (IGT3) or B84-83 (IGT3) - Body ground Always 10 kΩ or higher
B19-3 (IGT4) or B84-82 (IGT4) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Shuffle arrangement of the No. 1 ignition coil (among No. 1 to No. 4 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Start the engine and run it at idle for 10 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTCs.

Result
Result Proceed to
Same DTC is output A
Different No. 1 ignition coil DTC is output B



A

B

5.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - NO. 1 INTEGRATION RELAY)
a.

Disconnect the No. 1 ignition coil connectors.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
B13-1 (+B) - 1E-2 Always Below 1 Ω
B15-1 (+B) - 1E-2 Always Below 1 Ω
B17-1 (+B) - 1E-2 Always Below 1 Ω
B19-1 (+B) - 1E-2 Always Below 1 Ω
B13-1 (+B) or 1E-2 - Body ground Always 10 kΩ or higher
B15-1 (+B) or 1E-2 - Body ground Always 10 kΩ or higher
B17-1 (+B) or 1E-2 - Body ground Always 10 kΩ or higher
B19-1 (+B) or 1E-2 - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR