The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.
Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the mass air flow meter. The voltage level is proportional to the air flow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.
When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0100 | Mass air flow meter voltage less than 0.2 V or more than 4.9 V for 3 seconds
(1 trip detection logic) |
·
Open or short in mass air flow meter circuit ·
Mass air flow meter ·
No. 1 integration relay ·
ECM |
| P0102 | Mass air flow meter voltage less than 0.2 V for 3 seconds
(1 trip detection logic) |
·
Open or short in mass air flow meter circuit ·
Mass air flow meter ·
No. 1 integration relay ·
ECM |
| P0103 | Mass air flow meter voltage more than 4.9 V for 3 seconds
(1 trip detection logic) |
·
Open or short in mass air flow meter circuit ·
Mass air flow meter ·
No. 1 integration relay ·
ECM |
When any of these DTCs are stored, check the mass air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / MAF.
| Mass Air Flow Rate (gm/sec) | Malfunction |
|---|---|
| Approximately 0.0 | ·
Open in mass air flow meter power source circuit ·
Open or short in VG circuit |
| 160.0 or more | Open in E2G circuit |
If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.
Example:
When the sensor output voltage remains below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores a DTC.
| Frequency of Operation | Continuous |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0100, P0102 or P0103.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the value displayed on the tester.
| MAF (gm/sec) | Proceed to |
|---|---|
| 0.0 | A |
| 160.0 or more | B |
| Between 1.0 and 160.0* | C |
*: The value must change when the throttle valve is opened or closed with the engine running.
A
B
C
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)
Disconnect the mass air flow meter connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B72-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector
(to Mass Air Flow Meter) |
OK
NG
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B72-3 (VG) - B84-118 (VG) | Always | Below 1 Ω |
| B72-2 (E2G) - B84-116 (E2G) | Always | Below 1 Ω |
| B72-3 (VG) or B84-118 (VG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the mass air flow meter, referring to the ON-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).
Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION).
Inspect the function of the mass air flow meter.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Start the engine.
Check that the MAF value changes when the engine is raced.
The reading changes.
OK
NG
Disconnect the mass air flow meter connector.
Remove the No. 1 integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B72-1 (+B) - 1E-3 | Always | Below 1 Ω |
| B72-1 (+B) or 1E-3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B72-2 (E2G) - B84-116 (E2G) | Always | Below 1 Ω |
OK
NG
Disconnect the mass air flow meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B72-2 (E2G) - Body ground | Always | Below 1 Ω |
OK
NG