Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) Vehicle speed is 20 km/h (12.4 mph) or more.

(b) Engine speed is 1000 rpm or more.

(c) STA signal is on.


·

Park/neutral position switch assembly*1

·

Clutch start switch assembly*2

·

Starter relay (ST) circuit

·

Ignition switch assembly

·

ECM



*1: for Automatic Transaxle

*2: for Manual Transaxle

MONITOR STRATEGY

Required Sensors/Components (Main) Starter relay, Park/Neutral position switch assembly, Clutch start switch assembly and Ignition switch
Required Sensors/Components (Related) Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.4 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A231469E15
1.229,1.979 1.604,2.156 0.375,0.177 10 false Idling 0.396,2.25 1.604,2.573 1.208,0.323 10 false Ignition Switch ON 0.354,0.813 1.667,0.99 1.313,0.177 10 false 20 km/h (12.4 mph) 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.25,2.521 0.25,0.188 10 false [A] 2.583,2.125 2.792,2.302 0.208,0.177 10 false [B] 4.031,0.458 4.26,0.625 0.229,0.167 10 false [C] 4.906,3.344 5.135,3.51 0.229,0.167 10 false [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Read the value displayed on the tester when the ignition switch is turned to ON and the engine is started.

OK:
Ignition Switch Position Tester Display
ON OFF
START ON


Result
Result Proceed to
OK A
NG
(for automatic transaxle)
B
NG
(for manual transaxle)
C



A

B

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

C

6.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


f.

Read the value displayed on the tester when the ignition switch is turned to ON.

Result Proceed to
Remains ON A
OFF B



A

3.INSPECT ECM (STA TERMINAL VOLTAGE)

B

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT ECM (STA TERMINAL VOLTAGE)
a.
U158057E02
2.208,2.073 2.698,2.302 false 0.292,1.052 0.625,1.26 0.333,0.208 10 false A74 2.76,2.25 3.24,2.458 0.479,0.208 10 false STA 0.396,0.208 0.625,0.375 0.229,0.167 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.


Text in Illustration
*a Front view of wire harness connector
(to ECM)

Result
Tester Connection Switch Condition Specified Condition Proceed to
A74-48 (STA) - Body ground Ignition switch ON 11 to 14 V A
Below 1.5 V B


A

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY - ECM)

B

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
A107908E91
0.322,0.261 0.513,0.432 0.192,0.171 10 *a 0.461,1.529 0.587,1.678 0.126,0.149 10 B 2.323,2.5 2.449,2.649 0.126,0.149 10 L 0.596,1.613 1.195,1.613 false 2.248,1.991 2.333,2.455 false 1.936,0.86 2.284,1.045 0.348,0.185 10 RB 1.905,0.975 1.614,1.54 false

Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in any position other than P or N 10 kΩ or higher
2 (RB) - 5 (L) Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)

Result
Result Proceed to
Short between 4 (B) and 5 (L) A
Short between 2 (RB) and 5 (L) B
Within standard range C



A

5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

C

10.INSPECT IGNITION SWITCH ASSEMBLY
5.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).



NEXT

10.INSPECT IGNITION SWITCH ASSEMBLY
6.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Disconnect the clutch start switch assembly connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


f.

Read the value displayed on the tester when the ignition switch is turned to ON.

Result
Result Proceed to
ON A
OFF B



A

7.INSPECT ECM (STA TERMINAL SIGNAL)

B

8.INSPECT CLUTCH START SWITCH ASSEMBLY
7.INSPECT ECM (STA TERMINAL SIGNAL)
a.
U158057E02
2.208,2.073 2.698,2.302 false 0.292,1.052 0.625,1.26 0.333,0.208 10 false A74 2.76,2.25 3.24,2.458 0.479,0.208 10 false STA 0.396,0.208 0.625,0.375 0.229,0.167 10 false *a

Disconnect the clutch start switch assembly connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.


Text in Illustration
*a Front view of wire harness connector
(to ECM)

Result
Tester Connection Switch Condition Specified Condition Proceed to
A74-48 (STA) - Body ground Ignition switch ON 11 to 14 V A
Below 1.5 V B


A

REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY - ECM)

B

8.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).

Result
Result Proceed to
NG A
OK B



A

9.REPLACE CLUTCH START SWITCH ASSEMBLY

B

10.INSPECT IGNITION SWITCH ASSEMBLY
9.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL).



NEXT

10.INSPECT IGNITION SWITCH ASSEMBLY
10.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

11.INSPECT ECM (NSW TERMINAL VOLTAGE)

NG

REPLACE IGNITION SWITCH ASSEMBLY

11.INSPECT ECM (NSW TERMINAL VOLTAGE)
a.
U158101E02
0.958,1.74 0.823,2.74 false 1.365,0.75 1.719,0.948 0.354,0.198 10 false B84 0.625,2.76 1.052,2.958 0.427,0.198 10 false NSW 0.281,0.333 0.479,0.542 0.198,0.208 10 false *a

Disconnect the park/neutral position switch assembly*1 or clutch start switch*2 connector.

*1: for Automatic Transaxle

*2: for Manual Transaxle


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.


Text in Illustration
*a Front view of wire harness connector
(to ECM)

Result
Tester Connection Switch Condition Specified Condition Proceed to
B84-52 (NSW) - Body ground Ignition switch ON 11 to 14 V A
(for automatic transaxle)
B
(for manual transaxle)
Below 1.5 V C


A

REPAIR OR REPLACE HARNESS OR CONNECTOR IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH - ECM)

C