Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2011.08–2014.07
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM J

2NZ-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition switch assembly to the park/neutral position switch assembly and also flows to terminal STA of the ECM (STA Signal).


WIRING DIAGRAM

A254125E08
0.676,4.543 1.181,4.684 0.505,0.140 10 Battery 0.566,3.084 0.930,3.240 0.364,0.156 10 MAIN 1.739,1.032 2.062,1.181 0.323,0.149 10 AM2 2.657,1.38 4.280,1.547 1.624,0.167 10 Ignition Switch Assembly 2.561,1.897 3.992,2.224 1.431,0.327 10 Park/Neutral Position Switch Assembly*1 2.608,3.246 4.590,3.426 1.982,0.180 10 Clutch Start Switch Assembly*2 2.391,4.447 2.616,4.589 0.225,0.142 10 ST 3.455,4.65 3.688,4.806 0.232,0.156 10 ST 4.145,4.685 5.395,4.841 1.250,0.156 10 to Starter Assembly 6.149,5.035 6.492,5.191 0.343,0.156 10 ECM 3.098,4.22 3.207,4.390 0.109,0.170 10 5 3.098,3.91 3.207,4.080 0.109,0.170 10 2 3.883,4.223 3.992,4.393 0.109,0.170 10 3 3.883,3.91 3.992,4.080 0.109,0.170 10 1 2.561,1.745 2.828,1.890 0.267,0.144 10 B69 2.615,3.104 3.028,3.262 0.413,0.158 10 A39 3.078,0.804 3.393,0.945 0.314,0.141 10 AM2 3.781,0.804 4.066,0.945 0.285,0.141 10 ST2 2.86,0.811 2.973,0.960 0.113,0.149 10 5 4.172,0.811 4.285,0.960 0.113,0.149 10 7 4.475,2.351 4.583,2.510 0.108,0.159 10 5 3.064,2.71 3.222,2.870 0.159,0.159 10 1 4.456,1.519 4.564,1.679 0.108,0.159 10 4 3.97,2.71 4.119,2.870 0.149,0.159 10 2 5.445,3.375 5.628,3.524 0.184,0.149 10 48 5.445,2.654 5.628,2.803 0.184,0.149 10 52 5.417,3.539 5.696,3.691 0.279,0.152 10 A74 5.417,2.814 5.696,2.966 0.279,0.152 10 B84 5.767,3.526 6.062,3.679 0.295,0.152 10 STA 5.767,2.822 6.117,2.975 0.350,0.152 10 NSW 2.643,1.246 2.928,1.401 0.286,0.156 10 F13 4.349,1.736 4.513,1.956 0.164,0.220 10 L 4.591,1.736 4.755,1.956 0.164,0.220 10 B 4.093,1.943 4.259,2.097 0.166,0.154 10 P 4.093,2.128 4.259,2.283 0.166,0.154 10 N 3.932,5.136 5.662,5.319 1.730,0.184 10 *1: for Automatic Transaxle 3.932,5.407 5.763,5.564 1.832,0.157 10 *2: for Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if engine can be cranked.

Result
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

B

13.READ VALUE USING INTELLIGENT TESTER
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the tester when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON


Result
Result Proceed to
Outside standard range (for manual transaxle) A
Outside standard range (for automatic transaxle) B
Within standard range (for manual transaxle) C
Within standard range (for automatic transaxle) D



A

3.INSPECT CLUTCH START SWITCH ASSEMBLY

B

7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY -ECM - ST RELAY)

D

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
3.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

4.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

4.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>2NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F13-7 (ST2) - A39-2 Always Below 1 Ω
F13-7 (ST2) - A84-52 (NSW) Always Below 1 Ω
F13-7 (ST2) or A39-2 - Body ground Always 10 kΩ or higher
F13-7 (ST2) or A84-52 (NSW) - Body ground Always 10 kΩ or higher



OK

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY -ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY -ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Disconnect the clutch start switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - A74-48 (STA) Always Below 1 Ω
ST relay terminal 2 - A39-1 Always Below 1 Ω
A74-48 (STA), A39-1 or ST relay terminal 2 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B


A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

11.INSPECT BATTERY
7.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>U441E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>2NZ-FE STARTING>IGNITION SWITCH>INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F13-7 (ST2) - B69-4 (B) Always Below 1 Ω
F13-7 (ST2) - B84-52 (NSW) Always Below 1 Ω
F13-7 (ST2) or B69-4 (B) - Body ground Always 10 kΩ or higher
F13-7 (ST2) or B84-52 (NSW) - Body ground Always 10 kΩ or higher



OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Disconnect the park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - A74-48 (STA) Always Below 1 Ω
ST relay terminal 2 - B69-5 (L) Always Below 1 Ω
A74-48 (STA), B69-5 (L) or ST relay terminal 2 - Body ground Always 10 kΩ or higher



OK

11.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT BATTERY
a.

Check that the battery is not depleted.


OK:

Battery is not depleted.



OK

12.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

12.CHECK BATTERY TERMINAL
a.

check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE BATTERY TERMINAL

13.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Check the value displayed on the tester when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

14.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
14.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-48 (STA) - ST relay terminal 2 Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR