Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  


DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed to the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No. DTC Detection Condition Trouble Area
P0340 When one of following conditions is met:
·

No camshaft position sensor signal to ECM while cranking

(2 trip detection logic)

·

Camshaft/crankshaft misalignment detected at engine speed of 600 rpm or more

(1 trip detection logic)


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Intake camshaft

·

Jumped tooth of timing chain

·

ECM



HINT:

DTC P0340 indicates a malfunction relating to the camshaft position sensor circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).

Reference: Inspection using an oscilloscope (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0335).


MONITOR DESCRIPTION

If no signal is transmitted by the camshaft position sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Wait 10 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0340.

11.

Check DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0340)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read DTCs.

Result
Result Proceed to
DTC P0340 is output A
DTC P0340 and other DTCs are output B

HINT:

If any DTCs other than P0340 are output, troubleshoot those DTCs first.




A

2.INSPECT CAMSHAFT POSITION SENSOR

B

2.INSPECT CAMSHAFT POSITION SENSOR
a.


OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B30-1 - B84-99 (VV1+) Always Below 1 Ω
B30-2 - B84-121 (NE-) Always Below 1 Ω
B30-1 or B84-99 (VV1+) - Body ground Always 10 kΩ or higher
B30-2 or B84-121 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
A369509E02
0.427,1.583 0.969,1.781 0.542,0.198 10 false *a 2.667,1.771 2.938,1.938 0.271,0.167 10 false *b 2.104,1.552 2.333,1.75 0.229,0.198 10 false *c

Check the camshaft position sensor installation.

OK:

Sensor is installed correctly.



Text in Illustration
*a OK
*b NG
*c Clearance


OK

5.CHECK VALVE TIMING

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

5.CHECK VALVE TIMING

OK

6.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

6.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Inspect the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.




OK

7.REPLACE CAMSHAFT POSITION SENSOR

NG

7.REPLACE CAMSHAFT POSITION SENSOR
a.


NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (P0340)
8.CHECK WHETHER DTC OUTPUT RECURS (P0340)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Start the engine.


f.

Idle the engine for 10 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the pending DTCs.

Result
Result Proceed to
DTC P0340 is output A
DTC is not output B

HINT:

If the engine does not start, replace the ECM.




A

B

END