Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › CAMSHAFT › 2011.08–2016.09
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248086 CAMSHAFT A

2NZ-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13050 1.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

NOTICE:

Install the camshaft timing gear assembly onto the camshaft with the lock pin of the camshaft timing gear assembly released.


a.
A116230E08
1.354,0.906 1.938,0.323 true 1.021,0.969 0.49,1.635 true 1.948,0.198 2.135,0.396 0.188,0.198 10 false *1 0.323,1.604 0.51,1.802 0.188,0.198 10 false *2

Put the camshaft timing gear assembly and camshaft together with the straight pin of the groove.

Text in Illustration
*1 Straight Pin
*2 Groove


b.

Turn the camshaft timing gear assembly clockwise while pushing it gently toward the camshaft. Push further at the position where the pin fits into the groove.

NOTICE:

Do not turn the camshaft timing gear to the retard angle (to the right).



c.

Check that there is no clearance between the gear flange and the camshaft.


d.

Tighten the flange bolt with the camshaft timing gear fixed.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:
·

Do not lock the camshaft timing gear assembly when tightening the bolt.

·

Release the lock pin of the camshaft timing gear assembly first, and tighten the bolt when the lock pin is locked in the most retarded position.

·

Tightening the bolts with the lock pin locked could cause breakage of the lock pin.




e.

Check that the camshaft timing gear assembly can move to the retard angle (to the right) and is locked in the most retarded position.


Hide 13511 2.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft and camshaft journals.


b.
A116220E10
1.646,0.917 0.854,0.104 true 1.688,1.073 2.427,1.792 true 0.677,0.021 0.854,0.188 0.177,0.167 10 false *a 2.458,1.729 3.25,2.125 0.792,0.396 10 true *b

Install the chain onto the camshaft timing gear with the paint mark and the timing mark aligned as shown in the illustration.

Text in Illustration
*a Paint Mark
*b Timing Mark


c.
A116222E01
0.757,2.555 0.913,2.736 0.156,0.182 10 3 1.381,2.555 1.537,2.736 0.156,0.182 10 1 2.072,2.555 2.228,2.736 0.156,0.182 10 2 2.714,2.555 2.87,2.736 0.156,0.182 10 4

Examine the front marks and numbers on the No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts, in several steps, in the sequence shown in the illustration.

Torque:
13 N*m (129 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



Hide 13512 3.INSTALL NO. 2 CAMSHAFT

a.

Install the No. 2 camshaft.


b.
A116224E10
1.458,0.469 1.073,0.125 true 1.521,0.573 0.479,1.323 true 1.469,0.917 1.469,1.792 true 1.385,1.823 1.552,1.99 0.167,0.167 10 false *1 0.885,0.021 1.052,0.188 0.167,0.167 10 false *a 0.333,1.344 0.875,1.771 0.542,0.427 10 true *b

Hold the chain and align the timing mark on the camshaft timing sprocket with the paint mark of the chain.

Text in Illustration
*1 Pin
*a Paint Mark
*b Timing Mark


c.

Align the alignment pin hole in the camshaft timing sprocket with the alignment pin of the camshaft, and install the sprocket onto the camshaft.


d.

Provisionally install the flange bolt.


e.
A116223E12
1.167,2.177 0.854,2.604 true 1.5,1.563 2.635,2.594 2.635,2.594 2.802,1.573 true 1.938,1.552 2.635,2.583 2.635,2.583 2.375,1.552 true 1.042,0.167 1.198,0.344 0.156,0.177 10 false 3 1.677,0.167 1.833,0.344 0.156,0.177 10 false 1 2.323,0.167 2.479,0.344 0.156,0.177 10 false 2 2.969,0.167 3.125,0.344 0.156,0.177 10 false 4 0.375,0.969 0.531,1.146 0.156,0.177 10 false 5 0.688,2.563 0.854,2.74 0.167,0.177 10 false *1 2.563,2.615 2.729,2.792 0.167,0.177 10 false *2

Examine the front marks and numbers on the No. 1 and No. 2 camshaft bearing caps and check that the order is as shown in the illustration. Then uniformly tighten the bolts, in several steps, in the sequence shown in the illustration.

Text in Illustration
*1 No. 1 Bearing Cap
*2 No. 2 Bearing Cap

Torque:
13 N*m (129 kgf*cm, 9 ft.*lbf)

for No. 2 bearing cap

23 N*m (235 kgf*cm, 17 ft.*lbf)

for No. 1 bearing cap


NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



f.
A116225

Using a union nut wrench, hold the hexagonal lobe of the No. 2 camshaft and install the flange bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

HINT:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



g.

Remove the bar from the timing chain tensioner.


h.
A116203E27
2.156,1.063 2.469,1.833 true 2.427,1.844 2.594,2.031 0.167,0.188 10 false *a

Turn the crankshaft damper and align the timing notch with the timing mark "0" of the oil pump.

Text in Illustration
*a Timing Notch


i.
A116207E16
1.094,0.729 1.135,1.781 1.135,1.781 2.031,1.521 true 2.208,1.031 1.146,1.771 true 1.167,0.625 2.479,0.167 2.479,0.167 2.188,0.917 true 1.021,1.802 1.208,1.969 0.188,0.167 10 false *b 2.51,0.021 3.302,0.354 0.792,0.333 10 true *a

Check that all the pairs of timing marks are aligned.

Text in Illustration
*a Paint Mark
*b Timing Mark


j.

Apply adhesive to 2 or 3 threads of the screw plug end.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



k.

Using an 8 mm (0.31 in.) hexagon wrench, install the screw plug.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23820 7.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 9.INSPECT FOR OIL LEAK

Hide 51441C 11.INSTALL ENGINE UNDER COVER RH (for Plastic Type)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Hide 51405A 12.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)