The ECM uses the signals from the throttle position sensor, mass air flow meter and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.
Then the ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical problems of the shift solenoid valve SL, valve body and torque converter transaxle (clutch, brake or gear etc.).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0741 | (a) Lock-up does not occur when driving in lock-up range or lock-up remains ON in lock-up OFF range. (2 trip detection logic)
(b) When lock-up is ON, clutch or brake slippage occurs or gear breaks. (2-trip detection logic) |
·
Shift solenoid valve SL remains open or closed ·
Valve body is blocked ·
Shift solenoid valve SL ·
Torque converter assembly ·
Automatic transaxle (clutch, brake or gear etc.) ·
Line pressure is too low ·
ECM |
Torque converter lock-up is controlled by the ECM based on the speed sensor (NT), engine speed (NE), engine load, engine temperature, vehicle speed, transmission fluid temperature, and gear selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input turbine speed (NT). The ECM calculates the actual transmission gear by comparing input turbine speed (NT) to output shaft speed. When conditions are appropriate, the ECM requests lock-up by applying the control voltage to the shift solenoid SL. When the SL is turned on, it applies pressure to the lock-up relay valve and locks the torque converter.
If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it has not been requested, the ECM interprets this as a fault in the shift solenoid valve SL or lock-up system performance. The ECM turns on the MIL and stores the DTC.
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
It is possible to display the Data List during the Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Lock Up.
In accordance with the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Active the Lock Up | [Test Details]
Control the shift solenoid SL to set automatic transaxle to lock-up condition. |
ON/OFF | Possible to check SL operation.
[Vehicle Condition] Vehicle speed: 60 km/h (36 mph) or more, and 4th gear |
This test can be conducted when the vehicle speed is 60 km/h (36 mph) or more.
This test can be conducted in 4th gear.
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.
Slowly, but not fully, release the accelerator pedal in order to decelerate. (Fully releasing the pedal will close the throttle valve and lock-up may be turned off.)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs using the tester.
| Result | Proceed to |
|---|---|
| Only DTC P0741 is output | A |
| P0741 and other DTCs are output | B |
If any other DTCs besides P0741 are output, perform troubleshooting for those DTCs first.
A
B
Remove shift solenoid valve SL.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Solenoid Body (SL) | 20°C (68°F) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector and the negative (-) lead to the solenoid body to check the solenoid valve operation.
The solenoid makes operating sounds.
| *a | Component without harness connected
(Shift Solenoid Valve SL) |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).
There are no foreign objects on any valves and they operate smoothly.
OK
NG
Check the torque converter assembly (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION).
The torque converter operates normally.
OK
(See pageDrivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL)
NG
(See pageDrivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL)