The ECM uses signals from the vehicle speed sensor and speed sensor NT to detect the actual gear position (1st, 2nd, 3rd or 4th).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect the mechanical problems of the shift solenoid valves, the valve body or automatic transaxle (clutch, brake or gear etc.).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0751 | S1 stuck OFF malfunction*1:
ECM determines there is malfunction when both of following conditions are met (2 trip detection logic). (a) When ECM directs gearshift to switch to 1st gear, actual gear is shifted to 4th. (b) When ECM directs gearshift to switch to 4th gear, actual gear is shifted to 4th. |
·
Shift solenoid valve S1 remains closed ·
Valve body is blocked ·
Shift solenoid valve S1 ·
Automatic transaxle (clutch, brake or gear etc.) |
| S1 stuck ON malfunction*2:
ECM determines that there is malfunction when both of following conditions are met (2 trip detection logic). (a) When ECM directs gearshift to switch from 3rd to 4th gear, actual gear is not shifted as above. (b) When ECM directs gearshift to switch to 4th gear, engine speed surges 1100 rpm or more. |
·
Shift solenoid valve S1 remains open ·
Valve body is blocked ·
Shift solenoid valve S1 ·
Automatic transaxle (clutch, brake or gear etc.) |
Gear positions in the event of a solenoid valve mechanical problem:
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th |
| *1: Actual gear position under S1 stuck OFF malfunction | 4th | 3rd | 3rd | 4th |
| *2: Actual gear position under S1 stuck ON malfunction | 1st | 2nd | 2nd | 1st |
This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of shift solenoid valve S1.
The ECM controls the gearshifts by turning the shift solenoid valves ON/OFF. When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
In accordance with the display on the tester, perform the Active Test.
While driving, the shift position can be forcibly changed using the intelligent tester.
Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | [Test Details]
Operate shift solenoid valve and set each shift position. [Others] ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
1st/2nd/3rd/4th | Possible to check operation of shift solenoid valves.
[Vehicle Condition] vehicle speed: Less than 50 km/h (30 mph) |
This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
The 3rd to 4th up-shifting must be performed with the accelerator pedal released.
The 4th to 3rd down-shifting must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift more than once in succession.
The shift position commanded by the ECM is shown in the Data List/Shift Status display on the intelligent tester.
Shift solenoid valve S1 is turned on/off normally when the shift lever is in the D position:
| Gearshift controlled by ECM | 1st | 2nd | 3rd | 4th |
| Shift solenoid valve S1 | ON | ON | OFF | OFF |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs using the tester.
| Result | Proceed to |
|---|---|
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
If any DTCs besides P0751 are output, perform troubleshooting for those DTCs first.
A
B
Remove shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Solenoid Body | 20°C (68°F) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector and the negative (-) lead to the solenoid body to check the solenoid valve operation.
The solenoid makes operating sounds.
| *a | Component without harness connected
(Shift Solenoid Valve S1) |
OK
NG
OK
(See pageDrivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL)
NG