Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. DTC Detection Condition Trouble Area
C1468
C1469
C146A
C146B
Open or short in the solenoid circuit continues for 0.05 seconds or more.
·

Brake actuator assembly



WIRING DIAGRAM

C243323E01
0.634,4.243 0.924,4.426 0.289,0.184 10 ALT 1.487,1.338 2.201,1.661 0.714,0.323 10 ABS NO. 2 0.709,5.906 1.189,6.219 0.479,0.313 10 Battery 3.511,1.303 3.801,1.466 0.291,0.163 10 +BS 3.205,1.054 3.408,1.208 0.203,0.153 10 12 4.617,0.965 5.360,1.617 0.743,0.652 10 Solenoid Relay 5.912,1.945 6.337,2.096 0.425,0.151 10 SFRH 5.912,2.464 6.337,2.615 0.425,0.151 10 SFLH 5.912,2.956 6.337,3.106 0.425,0.151 10 SRRH 5.912,3.461 6.337,3.611 0.425,0.151 10 SRLH 5.912,3.959 6.337,4.110 0.425,0.151 10 SFRR 5.912,4.482 6.337,4.632 0.425,0.151 10 SFLR 5.912,4.983 6.337,5.134 0.425,0.151 10 SRRR 5.912,5.472 6.337,5.622 0.425,0.151 10 SRLR 4.439,3.97 5.580,4.116 1.141,0.146 10 Skid Control ECU 4.209,7.789 4.634,7.951 0.425,0.162 10 A55 4.209,7.951 5.819,8.105 1.610,0.154 10 Brake Actuator Assembly 3.495,5.071 3.902,5.235 0.407,0.164 10 GND1 3.281,4.957 3.402,5.121 0.122,0.164 10 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).



b.

Start the engine.


c.

Drive the vehicle at the speed of 20 km/h (12 mph) or more for 30 seconds or more.



Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C

HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the brake actuator assembly (skid control ECU (brake actuator assembly)), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




A

B

C