Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › 2014.07–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

EBD operation is not possible.


WIRING DIAGRAM

C301975E02
0.813,4.781 1.063,4.969 0.25,0.188 10 false F1 0.802,4.948 2.75,5.146 1.948,0.198 10 false Combination Meter Assembly 4.031,4.875 4.406,5.073 0.375,0.198 10 false A25 4.031,5.031 6.188,5.604 2.156,0.573 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 3.615,4.542 3.729,4.719 0.115,0.177 10 false 1 3.615,5.698 3.771,5.896 0.156,0.198 10 false 2 3.719,4.813 3.844,5.01 0.125,0.198 10 false + 3.719,5.458 3.865,5.656 0.146,0.198 10 false E 5.26,4.042 5.583,4.219 0.323,0.177 10 false A54 5.26,4.198 6.823,4.583 1.563,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 1.375,3.406 1.969,3.573 0.594,0.167 10 false CAN I/F 1.458,2.01 1.844,2.198 0.385,0.188 10 false CPU 1.552,1.531 2.01,1.75 0.458,0.219 10 false Brake 1.75,1.063 2,1.292 0.25,0.229 10 false IG 1.063,6.344 2.906,6.552 1.844,0.208 10 false : CAN Communication Line 2.469,4.156 2.76,4.344 0.292,0.188 10 false SW 2.802,4.052 3.031,4.24 0.229,0.188 10 false 12 4.115,0.594 5.156,0.802 1.042,0.208 10 false ECU-IG NO. 2 5.229,0.313 5.438,0.5 0.208,0.188 10 false 34 5.49,0.438 5.792,0.615 0.302,0.177 10 false IG1 5.292,1.531 5.438,1.74 0.146,0.208 10 false 1 5.479,1.667 5.948,1.875 0.469,0.208 10 false GND1 2.313,0.427 3.646,0.698 1.333,0.271 10 false from IG NO. 2 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C235854E03
0.175,0.265 0.361,0.426 0.186,0.161 10 *a 1.564,1.153 1.327,1.57 false 1.876,1.14 2.125,1.574 false 2.145,1.553 2.244,1.693 0.099,0.140 10 + 1.239,1.541 1.338,1.681 0.099,0.140 10 -

Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A25 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))

e.

Reconnect the A25 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


f.

Reinstall the reservoir filler cap and strainer.



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F1 combination meter assembly connector and the A25 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-12 (SW) - A25-1 (+) Always Below 1 Ω
A25-2 (E) - Body ground Always Below 1 Ω
F1-12 (SW) or A25-1 (+) - Body ground Always 10 kΩ or higher



c.

Reconnect the combination meter assembly connector and the A25 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.



OK

8.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

8.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/OFF or ON OFF: Warning light off
ON: Warning light on
-


g.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light OFF/ON Observe combination meter
[Vehicle condition]
Vehicle stopped

Result
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B

h.

Connect the intelligent tester to the DLC3.



A

B