Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › 2011.08–2014.07
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1401  Front Speed Sensor RH Malfunction  C1402  Front Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for ABS control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU are connected, the following waveform is output.


C235852E02
6.457,0.995 6.957,1.158 0.500,0.163 10 1.6 V 6.457,1.355 6.970,1.508 0.513,0.154 10 0.8 V 1.819,1.143 2.221,1.143 false 2.342,1.955 2.689,1.774 false 2.289,1.08 2.475,1.241 0.186,0.161 10 *1 2.75,1.664 2.936,1.825 0.186,0.161 10 *2 4.73,1.715 4.916,1.876 0.186,0.161 10 *b 5.654,1.715 5.839,1.876 0.186,0.161 10 *c 3.787,0.541 3.973,0.702 0.186,0.161 10 *a

Text in Illustration
*1 Speed Sensor *2 Speed Sensor Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -

DTC No. DTC Detection Condition Trouble Area
C1401
C1402
Any of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of 10 km/h (6 mph) or more, outputs from both front speed sensors are 0 km/h (0 mph) for 15 seconds or more. (except both rear speed sensors are 0 km/h (0 mph))


·

Front speed sensor RH/LH

·

Speed sensor rotor

·

Sensor installation



Test Mode Diagnosis Code
DTC No. DTC Detection Condition Trouble Area
C1271
C1272
Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Speed sensor rotor

·

Sensor installation



HINT:
·

DTC C1401 and C1271 are for the front speed sensor RH.

·

DTC C1402 and C1272 are for the front speed sensor LH.



WIRING DIAGRAM

C243289E01
1.289,1.126 1.579,1.283 0.290,0.156 10 A19 1.289,1.295 2.788,1.451 1.498,0.156 10 Front Speed Sensor LH 2.107,0.388 2.399,0.541 0.293,0.153 10 FL+ 2.107,0.864 2.399,1.018 0.293,0.153 10 FL- 5.339,0.402 5.632,0.555 0.293,0.153 10 FL+ 5.339,0.878 5.632,1.032 0.293,0.153 10 FL- 2.452,0.273 2.553,0.418 0.101,0.145 10 2 2.452,0.777 2.553,0.922 0.101,0.145 10 1 5.096,0.279 5.269,0.427 0.173,0.148 10 19 5.096,0.783 5.269,0.931 0.173,0.148 10 18 1.289,2.688 1.579,2.844 0.290,0.156 10 A18 1.289,2.856 2.815,3.013 1.526,0.156 10 Front Speed Sensor RH 2.09,1.949 2.399,2.103 0.309,0.153 10 FR+ 2.107,2.426 2.399,2.579 0.293,0.153 10 FR- 5.339,1.964 5.660,2.117 0.320,0.153 10 FR+ 5.339,2.44 5.632,2.593 0.293,0.153 10 FR- 2.452,1.834 2.553,1.979 0.101,0.145 10 2 2.452,2.339 2.553,2.484 0.101,0.145 10 1 5.132,1.841 5.234,1.988 0.102,0.148 10 7 4.241,2.723 4.514,2.862 0.273,0.140 10 A54 5.13,2.345 5.237,2.493 0.107,0.148 10 6 4.23,2.88 7.075,3.066 2.845,0.186 10 Skid Control ECU (Brake Actuator Assembly)

PROCEDURE

1.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336E05
1.994,1.633 2.180,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Text in Illustration
*a Normal
*b Abnormal
*c Clearance


OK

2.INSPECT FRONT SPEED SENSOR TIP

NG

2.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.






OK

3.INSPECT FRONT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

3.INSPECT FRONT SPEED SENSOR ROTOR
a.

Remove the front axle hub sub-assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:

If the front axle hub assembly needs to be replaced, replace it together with the front drive outboard joint shaft assembly.



c.

Reinstall the front axle hub assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION).



OK

4.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR

4.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the tester, read the Data List.

ABS/VSC/TRC (Skid Control ECU)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h When driving at constant speed: No large fluctuations
FL Wheel Speed FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h When driving at constant speed: No large fluctuations


f.

Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



Result
Result Proceed to
NG A
OK B


A

5.REPLACE FRONT SPEED SENSOR

B

5.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.




NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1401 and C1402 are not output A
DTCs C1401 and/or C1402 are output B

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:
·

If the front axle hub assembly needs to be replaced, replace it together with the front drive outboard joint shaft assembly.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).




A

END

B

REPLACE FRONT SPEED SENSOR ROTOR