Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for RHD)
RM19S0E _55 Steering _051481 STEERING COLUMN _0248257 STEERING COLUMN ASSEMBLY(for RHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for RHD)  INSTALLATION  


PROCEDURE

Hide 45250 1.INSTALL STEERING COLUMN ASSEMBLY

a.

Install the steering column assembly onto the instrument panel reinforcement assembly with the 2 nuts and a new bolt.

Torque:
Bolt : 36 N*m (367 kgf*cm, 27 ft.*lbf)
Nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Be sure there is no interference around the wire harness.

·

There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.




b.

Connect all the connectors and clamp the wire harnesses onto the steering column assembly bracket.


c.

Connect the 2 steering column assembly connectors to the power steering ECU assembly.


d.

Install the wire harness clamp to the power steering ECU assembly.


Hide 45209 2.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C235440E02
1.01,4.073 0.615,4.115 0.615,4.115 0.99,4.167 true 2.458,2.635 2.135,2.521 2.135,2.521 2.406,2.677 true 1.844,4.188 1.594,4.188 1.594,4.188 1.281,3.885 false 2.146,3.25 1.896,3.25 false 1.677,3.823 1.813,3.979 0.135,0.156 10 false A 1.385,4.281 1.51,4.438 0.125,0.156 10 false B 2.625,2.958 2.75,3.115 0.125,0.156 10 false C 2.052,1.448 2.177,1.604 0.125,0.156 10 false D 0.427,4.021 0.594,4.177 0.167,0.156 10 false *a 1.938,2.406 2.104,2.563 0.167,0.156 10 false *a 0.51,2.271 0.677,2.427 0.167,0.156 10 false *b 2.76,2.271 2.927,2.427 0.167,0.156 10 false *c 1.865,4.104 2.031,4.26 0.167,0.156 10 false *1 2.167,3.177 2.333,3.333 0.167,0.156 10 false *2

Tighten the bolt C while aligning the No. 2 steering intermediate shaft assembly with the position D as shown in the illustration.

Text in Illustration
*1 Steering Sliding Yoke Sub-assembly
*2 No. 2 Steering Intermediate Shaft Assembly
*a Matchmark
*b Front of the Vehicle
*c Rear of the Vehicle

Standard D:

18.5 to 19.7 mm


Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


b.

Align the matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.

HINT:

When the steering sliding yoke sub-assembly is replaced with a new one, it has no matchmarks, so install it while the head of the bolt B faces the back of the vehicle as shown in the illustration.



c.

Install bolt B.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


d.

Tighten bolt A.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 45259A 3.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.

Install the column hole cover silencer sheet with the 2 clips.


b.

Install the floor carpet.


Hide 55106 4.INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY

Hide 5.INSTALL COMBINATION SWITCH ASSEMBLY

a.
C233279

Install the combination switch assembly onto the steering column assembly with the clamp.


b.

Connect all the connectors to the combination switch assembly.


Hide 45286B 6.INSTALL UPPER STEERING COLUMN COVER

a.

Engage the claw to install the upper steering column cover.


Hide 45287 7.INSTALL LOWER STEERING COLUMN COVER

a.

Engage the 4 claws to install the lower steering column cover.


b.

Install the 3 screws.


Hide 45100 8.INSTALL STEERING WHEEL ASSEMBLY

Hide 10. POSITION FRONT WHEELS FACING STRAIGHT AHEAD

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 13. PERFORM CALIBRATION OF TORQUE SENSOR ZERO POINT