Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248288 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Only Back Door cannot be Opened  


DESCRIPTION

The main body ECU receives signals from the back door opener switch assembly. Then, the main body ECU activates the back door lock motor.

WIRING DIAGRAM

B288674E03
0.521,2.885 1.521,3.229 1,0.344 10 false Back Door Lock Assembly 5.49,1.792 6.729,2.146 1.24,0.354 10 false Back Door Opener Switch Assembly 2.292,3.073 5.01,3.25 2.719,0.177 10 false Instrument Panel Junction Block Assembly 0.25,0.51 1.073,0.698 0.823,0.188 10 false from Battery 3.802,2.521 4.813,2.688 1.01,0.167 10 false Main Body ECU 1.219,2.292 1.625,2.448 0.406,0.156 10 false ACT+ 0.552,2.292 0.948,2.448 0.396,0.156 10 false ACT- 4.167,1.688 4.469,1.844 0.302,0.156 10 false TR+ 4.406,1.24 4.833,1.396 0.427,0.156 10 false BDSU 2.969,1.938 3.458,2.094 0.49,0.156 10 false BK/DR 4.958,1.021 5.188,1.177 0.229,0.156 10 false 23 3.896,1.479 4.031,1.635 0.135,0.156 10 false 6 2.104,1.083 2.333,1.24 0.229,0.156 10 false 8 0.375,2.177 0.479,2.333 0.104,0.156 10 false 2 6.552,1.125 6.74,1.281 0.188,0.156 10 false 2 5.458,1.115 5.635,1.271 0.177,0.156 10 false 3 1.656,2.188 1.781,2.344 0.125,0.156 10 false 1 5.625,1.115 5.833,1.271 0.208,0.156 10 false B 6.365,1.125 6.51,1.281 0.146,0.156 10 false L 2.927,0.646 3.198,0.802 0.271,0.156 10 false D/L 4.917,1.229 5.198,1.385 0.281,0.156 10 false F76 5.49,1.635 5.719,1.792 0.229,0.156 10 false P8 0.521,2.729 0.844,2.885 0.323,0.156 10 false P12 3.823,1.688 4.063,1.844 0.24,0.156 10 false MB 2.052,1.271 2.25,1.427 0.198,0.156 10 false 3B 2.104,2.094 2.24,2.25 0.135,0.156 10 false 9 2.063,2.281 2.292,2.438 0.229,0.156 10 false 3D 1.667,0.74 1.896,0.896 0.229,0.156 10 false *1 2.063,0.74 2.292,0.896 0.229,0.156 10 false *2 1.698,0.281 1.927,0.438 0.229,0.156 10 false 1 2.104,0.281 2.333,0.438 0.229,0.156 10 false 1 1.656,0.521 1.885,0.677 0.229,0.156 10 false 3E 2.052,0.521 2.281,0.677 0.229,0.156 10 false 3F 6.146,3.188 6.99,3.365 0.844,0.177 10 false *2: for RHD 6.146,2.906 6.99,3.083 0.844,0.177 10 false *1: for LHD

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK STATUS)
a.

Unlock all doors.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / Main Body / Data List.


f.

According to the display on the intelligent tester, read the Data List.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Open Back door open status / Prohibit or Permit Prohibit: Back door locked
Permit: Back door unlocked
-

OK:

The intelligent tester indicates Permit according to the door lock operation shown in the table.



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Trunk and Back-Door Open Back door lock motor OFF / ON -

OK:

The back door lock assembly unlatches when ON is selected.




OK

3.READ VALUE USING INTELLIGENT TESTER

NG

4.INSPECT BACK DOOR LOCK ASSEMBLY
3.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Open Handle SW Back door opener switch signal / OFF or ON OFF: Back door opener switch not pushed
ON: Back door opener switch pushed
-

OK:

The intelligent tester indicates ON or OFF according to the switch operation shown in the table.




OK

NG

7.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
4.INSPECT BACK DOOR LOCK ASSEMBLY
a.

Inspect the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE BACK DOOR LOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the P12 back door lock assembly connector.


b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P12-1 (ACT+) - 3D-9 (ACT+) Always Below 1 Ω
P12-2 (ACT-) - Body ground Always Below 1 Ω
P12-1 (ACT+) - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
U158210E02
2.76,2.115 2.896,2.438 false 6.531,0.958 6.698,1.115 0.167,0.156 10 false *B 6.531,0.635 6.698,0.792 0.167,0.156 10 false *A 6.198,0.948 6.375,1.125 0.177,0.177 10 false 3F 6.198,0.635 6.385,0.813 0.188,0.177 10 false 3E 1.938,0.198 2.135,0.375 0.198,0.177 10 false 3D 3.719,1.594 3.948,1.771 0.229,0.177 10 false MB 2.802,2.469 3.094,2.625 0.292,0.156 10 false TR+ 0.135,0.083 0.302,0.24 0.167,0.156 10 false *a

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3E-1 - 3D-9 Always 10 kΩ or higher
3E-1 - MB-6 (TR+) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
3F-1 - 3D-9 Always 10 kΩ or higher
3F-1 - MB-6 (TR+) Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
3D-9 - Body ground Battery positive (+) → 3E-1
Battery negative (-) → MB-6
11 to 14 V

for RHD
Tester Connection Condition Specified Condition
3D-9 - Body ground Battery positive (+) → 3F-1
Battery negative (-) → MB-6
11 to 14 V




OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Inspect the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION).



OK

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR OPENER SWITCH ASSEMBLY)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK DOOR OPENER SWITCH ASSEMBLY)
a.

Disconnect the F76 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-23 (BDSU) - P8-3 (B) Always Below 1 Ω
P8-2 (L) - Body ground Always Below 1 Ω
P8-3 (B) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR