Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248289 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

B289284E02
5.229,2.823 6.26,3 1.031,0.177 10 false Main Body ECU 5.229,2.677 5.552,2.854 0.323,0.177 10 false F76 0.875,2.698 1.198,2.875 0.323,0.177 10 false K12 0.875,2.865 2.333,3.104 1.458,0.24 10 false Door Control Receiver 3.615,0.823 4.344,1.021 0.729,0.198 10 false to Battery 2.615,0.969 3.51,1.167 0.896,0.198 10 false ECU-B NO. 2 5.208,1.76 5.531,1.938 0.323,0.177 10 false PRG 5.208,1.281 5.531,1.458 0.323,0.177 10 false RDA 1.813,2.25 2.135,2.427 0.323,0.177 10 false GND 1.813,1.781 2.135,1.958 0.323,0.177 10 false PRG 1.813,1.302 2.135,1.479 0.323,0.177 10 false RDA 2.208,2.135 2.438,2.313 0.229,0.177 10 false 1 4.969,1.656 5.146,1.833 0.177,0.177 10 false 25 4.958,1.188 5.135,1.365 0.177,0.177 10 false 26 2.208,1.667 2.438,1.844 0.229,0.177 10 false 3 2.208,1.188 2.438,1.365 0.229,0.177 10 false 2 2.208,0.729 2.438,0.906 0.229,0.177 10 false 5 1.917,0.833 2.146,1.01 0.229,0.177 10 false +B 3.948,2.135 4.177,2.313 0.229,0.177 10 false 2 4.698,2.135 4.927,2.313 0.229,0.177 10 false 1 4.969,2.135 5.146,2.313 0.177,0.177 10 false 17 3.865,2.698 4.938,3.042 1.073,0.344 10 false Unlock Warning Switch Assembly 3.865,2.542 4.188,2.719 0.323,0.177 10 false F15 5.208,2.229 5.552,2.406 0.344,0.177 10 false KSW

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the locked doors unlock (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Locked doors unlock.




OK

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

NG

2.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)
a.

Disconnect the F76 main body ECU connector.


b.

Disconnect the F15 unlock warning switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-17 (KSW) - F15-1 Always Below 1 Ω
F76-17 (KSW) - Body ground Always 10 kΩ or higher




OK

4.SWITCH TO SELF DIAGNOSTIC MODE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.SWITCH TO SELF DIAGNOSTIC MODE
a.

Switch to self-diagnostic mode.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the intelligent tester on.


iv.

Enter following menus: Body / Main Body / Utility / Wireless Door Lock Diagnosis Mode


v.

Proceed to the next step in accordance with the prompts on the intelligent tester screen.



b.
B110075E29
0.125,0.115 1.427,0.281 1.302,0.167 10 false Interior Light Output: 1.781,0.479 2.896,0.667 1.115,0.188 10 false T1: 0.25 seconds 1.802,0.875 2.823,1.063 1.021,0.188 10 false T2: 0.5 seconds 0.646,1.594 0.875,1.74 0.229,0.146 10 false ON 0.583,1.885 0.885,2.052 0.302,0.167 10 false OFF 1.521,2.354 1.708,2.5 0.188,0.146 10 false T1 2,2.344 2.198,2.49 0.198,0.146 10 false T2

Check that the system has switched to self-diagnostic mode by checking the map light assembly flash pattern.

OK:

Flash pattern is same as illustration on left.




NEXT

5.CHECK BY SELF DIAGNOSTIC MODE
5.CHECK BY SELF DIAGNOSTIC MODE
a.

Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the map light assembly.

B123864E23
0.156,0.083 1.448,0.25 1.292,0.167 10 false Interior Light Output: 1.479,1.75 2.396,1.927 0.917,0.177 10 false Normal Wave: 1.344,0.865 1.542,1.01 0.198,0.146 10 false T1 1.792,0.854 1.99,1.021 0.198,0.167 10 false T2 0.635,1.219 0.896,1.365 0.26,0.146 10 false ON 0.615,1.615 0.917,1.771 0.302,0.156 10 false OFF 3.719,1.208 3.948,1.354 0.229,0.146 10 false ON 3.677,1.583 3.99,1.729 0.313,0.146 10 false OFF 4.5,0.677 5.823,0.854 1.323,0.177 10 false Wave being received 4.219,1.823 6.177,2 1.958,0.177 10 false Mismatched Recognition Code: 0.417,3.75 0.729,3.906 0.313,0.156 10 false OFF 1.052,3.917 2.406,4.104 1.354,0.188 10 false No Diagnosis Output: 4.781,3.438 5.885,3.594 1.104,0.156 10 false T1: 0.25 seconds 4.792,3.802 5.875,3.969 1.083,0.167 10 false T2: 0.50 seconds

Result
Result Proceed to
Normal waves (light flash patterns) for lock and unlock switches are output A
Unmatching recognition code is output B
No diagnosis outputs C



A

B

6.REGISTER RECOGNITION CODE

C

7.CHECK RESPONSE OF DOOR CONTROL RECEIVER (RESPONSE)
6.REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

OK:

Recognition code can be registered.




OK

END

NG

REPLACE TRANSMITTER SUB-ASSEMBLY MODULE SET DOOR CONTROL

7.CHECK RESPONSE OF DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter from another vehicle.


b.

Press and hold down the door control transmitter switch.


c.

Check that an unmatching recognition code is output.


OK:

Unmatching recognition code is output.



OK

8.INSPECT TRANSMITTER BATTERY (VOLTAGE)

NG

11.CHECK WAVE ENVIRONMENT
8.INSPECT TRANSMITTER BATTERY (VOLTAGE)
B265632E02
1.752,0.39 2.237,0.184 2.237,0.184 2.383,0.184 false 2.455,0.119 2.766,0.332 0.311,0.213 10 *1

a.

Remove the battery from the door control transmitter module that does not operate. Attach a lead wire (0.6 mm (0.0236 in.)) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).

NOTICE:

Do not wrap the lead wire around the terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.


Text in Illustration
*1 Lead Wire


b.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.



c.
B268913E03
0.396,0.448 0.26,0.719 false 0.177,0.719 0.438,0.938 0.26,0.219 10 false *a

Measure the voltage according to the value(s) in the table below.

HINT:

When measuring the battery voltage, press one of the transmitter switches.


Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pushed 2.5 to 3.2 V


Text in Illustration
*a GND



OK

REPLACE TRANSMITTER SUB-ASSEMBLY MODULE SET DOOR CONTROL

NG

9.REPLACE TRANSMITTER BATTERY
9.REPLACE TRANSMITTER BATTERY
a.

Replace the transmitter battery (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).



NEXT

10.CHECK BY SELF DIAGNOSTIC MODE
10.CHECK BY SELF DIAGNOSTIC MODE
a.

Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the No. 1 room light assembly.

B123864E23
0.156,0.083 1.448,0.25 1.292,0.167 10 false Interior Light Output: 1.479,1.75 2.396,1.927 0.917,0.177 10 false Normal Wave: 1.344,0.865 1.542,1.01 0.198,0.146 10 false T1 1.792,0.854 1.99,1.021 0.198,0.167 10 false T2 0.635,1.219 0.896,1.365 0.26,0.146 10 false ON 0.615,1.615 0.917,1.771 0.302,0.156 10 false OFF 3.719,1.208 3.948,1.354 0.229,0.146 10 false ON 3.677,1.583 3.99,1.729 0.313,0.146 10 false OFF 4.5,0.677 5.823,0.854 1.323,0.177 10 false Wave being received 4.219,1.823 6.177,2 1.958,0.177 10 false Mismatched Recognition Code: 0.417,3.75 0.729,3.906 0.313,0.156 10 false OFF 1.052,3.917 2.406,4.104 1.354,0.188 10 false No Diagnosis Output: 4.781,3.438 5.885,3.594 1.104,0.156 10 false T1: 0.25 seconds 4.792,3.802 5.875,3.969 1.083,0.167 10 false T2: 0.50 seconds

Result
Result Proceed to
Normal waves (light flash patterns) for LOCK and UNLOCK switches are output A
Unmatching recognition code is output B
No diagnosis outputs



A

END (TRANSMITTER BATTERY IS DEFECTIVE)

B

REPLACE TRANSMITTER SUB-ASSEMBLY MODULE SET DOOR CONTROL

11.CHECK WAVE ENVIRONMENT
a.

Bring the transmitter near the door control receiver, and perform a wireless operation check.

OK:

Wireless functions operate normally.


HINT:
·

When the transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.





OK

12.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)

NG

AFFECTED BY WAVE INTERFERENCE

12.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)
a.

Disconnect the K12 door control receiver connector.


U158147E03
1.208,2.094 0.781,2.229 false 2.646,2.292 2.188,2.083 false 0.104,0.042 0.333,0.208 0.229,0.167 10 false *a 0.458,2.177 0.844,2.365 0.385,0.188 10 false GND 2.688,2.229 2.927,2.417 0.24,0.188 10 false +B 1.563,0.854 1.823,1.031 0.26,0.177 10 false K12

b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
K12-5 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)


c.

Reconnect the K12 door control receiver connector.



OK

13.INSPECT DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT DOOR CONTROL RECEIVER (OUTPUT)
U158149E01
0.1,0.027 0.269,0.188 0.169,0.161 10 *a 2.375,1.835 2.717,1.991 0.342,0.156 10 RDA 1.859,1.325 2.346,1.858 false 1.578,0.142 1.842,0.323 0.264,0.181 10 K12

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K12-2 (RDA) - Body ground Ignition switch off, all doors closed and door control transmitter switch off 11 to 14 V
Ignition switch off, all doors closed and door control transmitter switch on pulse generation


Text in Illustration
*a Component with harness connected
(Door Control Receiver)

Result
Result Proceed to
OK A
NG (for 5 Door) B
NG (for 3 Door) C



A

14.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)

B

C

14.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the F76 main body ECU connector.


b.

Disconnect the K12 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F76-26 (RDA) - K12-2 (RDA) Always Below 1 Ω
F76-26 (RDA) or K12-2 (RDA) - Body ground Always 10 kΩ or higher
F76-25 (PRG) - K12-3 (PRG) Always Below 1 Ω
F76-25 (PRG) or K12-3 (PRG) - Body ground Always 10 kΩ or higher



d.

Reconnect the main body ECU connector and door control receiver connector.



OK

15.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or normally functioning one.

HINT:




NEXT

16.REGISTER RECOGNITION CODE
16.REGISTER RECOGNITION CODE
a.

Perform the Registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).



NEXT

17.CHECK DOOR CONTROL RECEIVER (OPERATION)
17.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.


OK:

Doors can be locked and unlocked with transmitter.



OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG