Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248330 AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH (for 5 Door), door side airbag sensor LH (for 3 Door) and No. 2 side airbag sensor assembly LH.

The side airbag sensor assembly LH (for 5 Door), door side airbag sensor LH (for 3 Door) and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected for the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No. DTC Detection Condition Trouble Area
B1647/82
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

·

Side airbag sensor assembly LH malfunction (for 5 Door)

·

Door side airbag sensor LH malfunction (for 3 Door)

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH (for 5 Door)

·

Door side airbag sensor LH (for 3 Door)

·

No. 2 side airbag sensor assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

C241048E17
5.544,1.643 5.949,1.795 0.404,0.153 10 BBL- 5.544,1.138 5.949,1.291 0.404,0.153 10 BBL+ 5.328,1.048 5.436,1.195 0.108,0.147 10 8 5.253,1.567 5.436,1.714 0.183,0.147 10 15 1.339,2.642 1.743,2.795 0.404,0.153 10 BDL+ 1.339,2.138 1.743,2.290 0.404,0.153 10 BDL- 1.828,2.066 2.010,2.214 0.183,0.147 10 2 1.828,2.585 2.010,2.732 0.183,0.147 10 1 1.339,1.633 1.743,1.786 0.404,0.153 10 BCL- 1.339,1.129 1.743,1.282 0.404,0.153 10 BCL+ 1.828,1.057 2.010,1.205 0.183,0.147 10 4 1.828,1.576 2.010,1.723 0.183,0.147 10 3 3.367,2.658 3.676,2.817 0.309,0.158 10 HK2 3.367,2.154 3.676,2.312 0.309,0.158 10 HK2 3.478,1.975 3.661,2.122 0.183,0.147 10 2 3.478,2.484 3.661,2.632 0.183,0.147 10 1 1.353,5.045 1.757,5.198 0.404,0.153 10 BDL- 1.353,4.527 1.757,4.679 0.404,0.153 10 BDL+ 1.842,4.441 2.024,4.588 0.183,0.147 10 2 1.842,4.959 2.024,5.107 0.183,0.147 10 1 5.38,5.619 5.668,5.782 0.288,0.163 10 K33 5.38,5.801 6.983,5.980 1.603,0.179 10 Airbag Sensor Assembly 0.357,3.28 0.645,3.442 0.288,0.163 10 K45 0.357,3.462 2.826,3.631 2.468,0.170 10 No. 2 Side Airbag Sensor Assembly LH 0.357,5.633 0.645,5.796 0.288,0.163 10 H16 0.357,5.815 2.147,5.985 1.790,0.170 10 Door Side Airbag Sensor LH 0.137,0.099 0.965,0.294 0.829,0.195 12 for 3 Door:

C241675E17
1.181,1.005 1.587,1.147 0.406,0.142 10 BBL+ 1.181,1.798 1.587,1.940 0.406,0.142 10 BBL- 5.693,1.005 6.099,1.147 0.406,0.142 10 BBL+ 5.693,1.798 6.099,1.940 0.406,0.142 10 BBL- 1.181,3.189 1.601,3.332 0.420,0.143 10 BCL+ 1.181,3.964 1.601,4.110 0.420,0.145 10 BCL- 3.892,3.186 4.309,3.336 0.416,0.150 10 BCL+ 3.892,3.968 4.274,4.106 0.382,0.139 10 BCL- 1.695,0.905 1.802,1.049 0.107,0.144 10 4 1.695,1.717 1.799,1.868 0.104,0.151 10 3 1.695,3.124 1.796,3.262 0.100,0.137 10 1 1.695,3.88 1.804,4.045 0.108,0.165 10 2 3.647,3.113 3.746,3.272 0.098,0.159 10 2 3.654,3.885 3.758,4.041 0.104,0.156 10 1 5.38,1.722 5.571,1.864 0.191,0.142 10 15 5.459,0.902 5.571,1.051 0.113,0.149 10 8 0.537,4.675 0.810,4.821 0.273,0.145 10 K21 3.717,4.689 3.984,4.852 0.267,0.163 10 K23 5.543,4.682 5.820,4.824 0.276,0.143 10 K33 0.537,4.836 2.625,4.975 2.088,0.139 10 Side Airbag Sensor Assembly LH 3.717,4.85 5.070,5.172 1.353,0.322 10 No. 2 Side Airbag Sensor Assembly LH 5.543,4.827 7.103,4.999 1.560,0.172 10 Airbag Sensor Assembly 0.131,0.08 0.953,0.277 0.823,0.198 12 for 5 Door:

PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
for 3 Door A
for 5 Door B



A

2.CHECK CONNECTORS

B

17.CHECK FLOOR WIRE (OPEN)
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor assembly LH.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK FLOOR WIRE (OPEN)
a.

Using a service wire, connect terminals 15 (BBL-) and 8 (BBL+) of connector B.

U158497E02
1.115,0.781 1.031,0.458 false 6,1.292 6.208,1.021 true 6.542,1.281 6.344,1.01 true 3.521,1.271 3.875,0.969 true 4.052,1.156 4.302,1.406 true 3.906,1.49 3.948,1.375 false 3.771,0.354 4.031,0.531 0.26,0.177 10 false K33 0.24,1.115 0.406,1.271 0.167,0.156 10 false *1 1.458,1.198 1.625,1.354 0.167,0.156 10 false *2 0.885,0.385 1.052,0.542 0.167,0.156 10 false *3 2.938,0.135 3.104,0.292 0.167,0.156 10 false *a 5.26,0.135 5.427,0.292 0.167,0.156 10 false *b 6.083,0.406 6.344,0.583 0.26,0.177 10 false K45 2.938,0.375 3.104,0.531 0.167,0.156 10 false *4 5.26,0.375 5.427,0.531 0.167,0.156 10 false *5 0.906,0.927 1.031,1.083 0.125,0.156 10 false C 1.208,0.927 1.323,1.083 0.115,0.156 10 false B 1.552,0.75 1.667,0.906 0.115,0.156 10 false A 0.521,0.75 0.646,0.906 0.125,0.156 10 false D 4.344,1.354 4.729,1.51 0.385,0.156 10 false BBL- 3.135,1.208 3.51,1.365 0.375,0.156 10 false BBL+ 3.813,1.51 4.104,1.667 0.292,0.156 10 false *6 6.396,1.292 6.802,1.448 0.406,0.156 10 false BCL+ 5.802,1.292 6.208,1.448 0.406,0.156 10 false BCL-

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-3 (BCL-) - K45-4 (BCL+) Always Below 1 Ω




OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.
U158501E02
2.24,2.573 1.927,2.938 true 2.406,2.552 2.625,2.917 true 1.469,0.208 1.563,0.833 false 0.792,0.813 0.917,0.969 0.125,0.156 10 false D 1.281,1.031 1.406,1.188 0.125,0.156 10 false C 1.677,1.031 1.802,1.188 0.125,0.156 10 false B 2.156,0.813 2.281,0.969 0.125,0.156 10 false A 0.365,1.281 0.552,1.438 0.188,0.156 10 false *1 0.865,1.594 1.063,1.75 0.198,0.156 10 false *a 1.125,2.115 1.292,2.26 0.167,0.146 10 false *4 1.094,2.375 1.365,2.552 0.271,0.177 10 false K45 2.573,2.938 2.969,3.094 0.396,0.156 10 false BCL+ 1.646,2.927 2.052,3.083 0.406,0.156 10 false BCL- 1.292,0.094 1.479,0.25 0.188,0.156 10 false *3 2.031,1.385 2.188,1.573 0.156,0.188 10 false *2

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-3 (BCL-) - K45-4 (BCL+) Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.
U158501E02
2.24,2.573 1.927,2.938 true 2.406,2.552 2.625,2.917 true 1.469,0.208 1.563,0.833 false 0.792,0.813 0.917,0.969 0.125,0.156 10 false D 1.281,1.031 1.406,1.188 0.125,0.156 10 false C 1.677,1.031 1.802,1.188 0.125,0.156 10 false B 2.156,0.813 2.281,0.969 0.125,0.156 10 false A 0.365,1.281 0.552,1.438 0.188,0.156 10 false *1 0.865,1.594 1.063,1.75 0.198,0.156 10 false *a 1.125,2.115 1.292,2.26 0.167,0.146 10 false *4 1.094,2.375 1.365,2.552 0.271,0.177 10 false K45 2.573,2.938 2.969,3.094 0.396,0.156 10 false BCL+ 1.646,2.927 2.052,3.083 0.406,0.156 10 false BCL- 1.292,0.094 1.479,0.25 0.188,0.156 10 false *3 2.031,1.385 2.188,1.573 0.156,0.188 10 false *2

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K45-3 (BCL-) - Body ground Ignition switch ON Below 1 V
K45-4 (BCL+) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U158501E02
2.24,2.573 1.927,2.938 true 2.406,2.552 2.625,2.917 true 1.469,0.208 1.563,0.833 false 0.792,0.813 0.917,0.969 0.125,0.156 10 false D 1.281,1.031 1.406,1.188 0.125,0.156 10 false C 1.677,1.031 1.802,1.188 0.125,0.156 10 false B 2.156,0.813 2.281,0.969 0.125,0.156 10 false A 0.365,1.281 0.552,1.438 0.188,0.156 10 false *1 0.865,1.594 1.063,1.75 0.198,0.156 10 false *a 1.125,2.115 1.292,2.26 0.167,0.146 10 false *4 1.094,2.375 1.365,2.552 0.271,0.177 10 false K45 2.573,2.938 2.969,3.094 0.396,0.156 10 false BCL+ 1.646,2.927 2.052,3.083 0.406,0.156 10 false BCL- 1.292,0.094 1.479,0.25 0.188,0.156 10 false *3 2.031,1.385 2.188,1.573 0.156,0.188 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-3 (BCL-) - Body ground Always 1 MΩ or higher
K45-4 (BCL+) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)



OK

7.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (OPEN)
a.

Using the service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

U158401E01
5.503,0.942 5.783,1.123 0.280,0.181 10 H16 0.43,1.181 0.600,1.341 0.170,0.161 10 *1 1.975,1.17 2.145,1.331 0.170,0.161 10 *2 1.072,0.411 1.242,0.571 0.170,0.161 10 *3 5.602,0.15 5.772,0.311 0.170,0.161 10 *b 3.263,0.15 3.433,0.311 0.170,0.161 10 *a 3.185,0.943 3.449,1.124 0.264,0.181 10 K45 5.602,0.384 5.772,0.545 0.170,0.161 10 *6 3.263,0.384 3.433,0.545 0.170,0.161 10 *5 1.476,0.974 1.601,1.127 0.125,0.152 10 C 1.79,0.974 1.900,1.127 0.111,0.152 10 B 2.085,0.792 2.200,0.944 0.114,0.152 10 A 0.76,0.792 0.863,0.944 0.104,0.152 10 F 5.595,1.311 5.994,1.463 0.398,0.152 10 BDL- 6.656,1.451 7.028,1.603 0.371,0.152 10 BDL+ 6.198,1.479 6.489,1.631 0.291,0.152 10 *7 3.457,1.391 3.859,1.543 0.402,0.152 10 BDL+ 3.961,1.391 4.367,1.543 0.406,0.152 10 BDL- 1.305,0.797 1.226,0.477 false 3.642,1.357 3.85,1.095 false 4.152,1.357 3.944,1.095 false 5.986,1.378 6.356,1.077 false 6.487,1.086 6.818,1.437 false 6.338,1.471 6.374,1.353 false 1.372,0.974 1.497,1.127 0.125,0.152 10 D 1.064,0.974 1.189,1.127 0.125,0.152 10 E 1.701,0.797 1.622,0.477 false 1.451,0.411 1.620,0.571 0.170,0.161 10 *4

Text in Illustration
*1 Door Side Airbag Sensor LH *2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH *4 Floor Wire
*5 Connector B *6 Connector E
*7 Service Wire - -
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-1 (BDL+) - K45-2 (BDL-) Always Below 1 Ω




OK

8.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT)

NG

13.CHECK FRONT DOOR WIRE LH (OPEN)
8.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT)
a.
U158407E02
2.031,2.563 1.792,2.938 true 2.167,2.563 2.354,2.927 true 1.531,0.531 1.51,0.885 false 2.01,0.531 1.979,0.885 false 0.906,0.865 1.01,1.021 0.104,0.156 10 false F 1.76,1.104 1.885,1.26 0.125,0.156 10 false C 2.135,1.104 2.26,1.26 0.125,0.156 10 false B 2.479,0.865 2.604,1.021 0.125,0.156 10 false A 0.49,1.365 0.677,1.521 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.563,0.438 1.729,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 1,2.01 1.177,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K45 2.198,2.948 2.552,3.104 0.354,0.156 10 false BDL- 1.573,2.948 1.948,3.104 0.375,0.156 10 false BDL+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.104 1.75,1.26 0.125,0.156 10 false D 1.26,1.104 1.385,1.26 0.125,0.156 10 false E

Disconnect the service wire from connector E.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-1 (BDL+) - K45-2 (BDL-) Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)



OK

9.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT TO B+)

NG

14.CHECK FRONT DOOR WIRE LH (SHORT)
9.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT TO B+)
a.
U158407E02
2.031,2.563 1.792,2.938 true 2.167,2.563 2.354,2.927 true 1.531,0.531 1.51,0.885 false 2.01,0.531 1.979,0.885 false 0.906,0.865 1.01,1.021 0.104,0.156 10 false F 1.76,1.104 1.885,1.26 0.125,0.156 10 false C 2.135,1.104 2.26,1.26 0.125,0.156 10 false B 2.479,0.865 2.604,1.021 0.125,0.156 10 false A 0.49,1.365 0.677,1.521 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.563,0.438 1.729,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 1,2.01 1.177,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K45 2.198,2.948 2.552,3.104 0.354,0.156 10 false BDL- 1.573,2.948 1.948,3.104 0.375,0.156 10 false BDL+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.104 1.75,1.26 0.125,0.156 10 false D 1.26,1.104 1.385,1.26 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K45-1 (BDL+) - Body ground Ignition switch ON Below 1 V
K45-2 (BDL-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)



OK

10.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT TO GROUND)

NG

15.CHECK FRONT DOOR WIRE LH (SHORT TO B+)
10.CHECK FLOOR WIRE AND FRONT DOOR WIRE LH (SHORT TO GROUND)
a.
U158407E02
2.031,2.563 1.792,2.938 true 2.167,2.563 2.354,2.927 true 1.531,0.531 1.51,0.885 false 2.01,0.531 1.979,0.885 false 0.906,0.865 1.01,1.021 0.104,0.156 10 false F 1.76,1.104 1.885,1.26 0.125,0.156 10 false C 2.135,1.104 2.26,1.26 0.125,0.156 10 false B 2.479,0.865 2.604,1.021 0.125,0.156 10 false A 0.49,1.365 0.677,1.521 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.563,0.438 1.729,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 1,2.01 1.177,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K45 2.198,2.948 2.552,3.104 0.354,0.156 10 false BDL- 1.573,2.948 1.948,3.104 0.375,0.156 10 false BDL+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.104 1.75,1.26 0.125,0.156 10 false D 1.26,1.104 1.385,1.26 0.125,0.156 10 false E

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K45-1 (BDL+) - Body ground Always 1 MΩ or higher
K45-2 (BDL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)



OK

11.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH

NG

16.CHECK FRONT DOOR WIRE LH (SHORT TO GROUND)
11.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C249132E01
0.638,1.489 0.808,1.650 0.170,0.161 10 *1 1.727,1.579 1.897,1.740 0.170,0.161 10 *2

Connect the connectors to the door side airbag sensor LH and airbag sensor assembly.


b.

Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1647/82 is output. A
DTC B1642/81 is output. B
DTC B1642/81 or B1647/82 is not output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

12.CHECK DOOR SIDE AIRBAG SENSOR LH

B

C

12.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C195583E03
0.403,1.497 0.558,1.652 0.155,0.155 10 *1 2.176,1.497 2.331,1.652 0.155,0.155 10 *2

Interchange the door side airbag sensor LH with the door side airbag sensor RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1642/81 or B1647/82 is not output. A
DTC B1647/82 is output. B
DTC B1642/81 is output. C

Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly LH

HINT:

Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.



A

B

C

13.CHECK FRONT DOOR WIRE LH (OPEN)
a.

Disconnect the floor wire connector from the front door wire LH.

U158405E01
4.957,0.942 5.237,1.123 0.280,0.181 10 H16 0.444,1.181 0.614,1.341 0.170,0.161 10 *1 2.101,1.17 2.271,1.331 0.170,0.161 10 *2 1.1,0.411 1.270,0.571 0.170,0.161 10 *3 5.07,0.15 5.240,0.311 0.170,0.161 10 *b 3.291,0.15 3.461,0.311 0.170,0.161 10 *a 3.279,0.862 3.576,1.043 0.297,0.181 10 HK2 5.07,0.384 5.240,0.545 0.170,0.161 10 *6 3.291,0.384 3.461,0.545 0.170,0.161 10 *5 1.602,0.974 1.727,1.127 0.125,0.152 10 C 1.916,0.974 2.026,1.127 0.111,0.152 10 B 2.211,0.792 2.326,0.944 0.114,0.152 10 A 0.788,0.792 0.891,0.944 0.104,0.152 10 F 5.07,1.311 5.450,1.463 0.380,0.152 10 BDL- 6.131,1.451 6.508,1.603 0.377,0.152 10 BDL+ 5.7,1.479 5.992,1.631 0.291,0.152 10 *7 3.653,1.489 4.055,1.641 0.402,0.152 10 BDL+ 4.158,1.489 4.564,1.641 0.406,0.152 10 BDL- 1.333,0.797 1.254,0.477 false 3.838,1.455 4.046,1.193 false 4.348,1.455 4.14,1.193 false 5.46,1.378 5.831,1.077 false 5.962,1.086 6.293,1.437 false 5.812,1.471 5.848,1.353 false 1.401,0.974 1.525,1.127 0.125,0.152 10 D 1.092,0.974 1.217,1.127 0.125,0.152 10 E 1.827,0.797 1.748,0.477 false 1.577,0.411 1.747,0.571 0.170,0.161 10 *4

Text in Illustration
*1 Door Side Airbag Sensor LH *2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH *4 Floor Wire
*5 Connector D *6 Connector E
*7 Service Wire - -
*a Front view of wire harness connector
(to Floor Wire)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)

HINT:

The service wire has already been inserted into connector E.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HK2-1 (BDL+) - HK2-2 (BDL-) Always Below 1 Ω




OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE LH

14.CHECK FRONT DOOR WIRE LH (SHORT)
a.
C355221E02
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false HK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDL+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDL-

Disconnect the floor wire connector from the front door wire LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HK2-1 (BDL+) - HK2-2 (BDL-) Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE LH

15.CHECK FRONT DOOR WIRE LH (SHORT TO B+)
a.

Turn the ignition switch off.


b.
C355221E02
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false HK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDL+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDL-

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the front door wire connector from the floor wire.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
HK2-1 (BDL+) - Body ground Ignition switch ON Below 1 V
HK2-2 (BDL-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE LH

16.CHECK FRONT DOOR WIRE LH (SHORT TO GROUND)
a.
C355221E02
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false HK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDL+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDL-

Disconnect the front door wire connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HK2-1 (BDL+) - Body ground Always 1 MΩ or higher
HK2-2 (BDL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE LH

17.CHECK FLOOR WIRE (OPEN)
a.

Using the service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

U158367E02
6.458,1.729 6.667,2 true 6.354,1.719 6.115,2 true 3.844,1.729 3.615,1.958 true 3.948,1.729 4.156,1.958 true 6.51,2.313 6.427,2.115 false 1.167,0.667 1.24,1.167 false 0.646,1.135 0.771,1.292 0.125,0.156 10 false D 1.031,1.323 1.156,1.479 0.125,0.156 10 false C 1.365,1.323 1.49,1.479 0.125,0.156 10 false B 1.75,1.146 1.875,1.302 0.125,0.156 10 false A 0.313,1.542 0.5,1.698 0.188,0.156 10 false *1 2.917,0.354 3.115,0.51 0.198,0.156 10 false *a 5.26,0.354 5.417,0.521 0.156,0.167 10 false *b 5.406,1.063 5.573,1.208 0.167,0.146 10 false *5 5.802,2.01 6.188,2.167 0.385,0.156 10 false BCL- 6.656,2.01 7.052,2.167 0.396,0.156 10 false BCL+ 5.365,1.448 5.656,1.604 0.292,0.156 10 false K23 3.094,1.063 3.26,1.208 0.167,0.146 10 false *4 3.063,1.448 3.375,1.604 0.313,0.156 10 false K21 6.5,2.354 6.823,2.51 0.323,0.156 10 false *6 4.177,1.948 4.573,2.104 0.396,0.156 10 false BCL- 3.25,1.948 3.656,2.104 0.406,0.156 10 false BCL+ 1,0.583 1.188,0.74 0.188,0.156 10 false *3 1.656,1.542 1.813,1.729 0.156,0.188 10 false *2

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH *2 Side Airbag Sensor Assembly LH
*3 Floor Wire *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (BCL+) - K21-2 (BCL-) Always Below 1 Ω




OK

18.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

18.CHECK FLOOR WIRE (SHORT)
a.
U158373E02
2.031,2.563 1.75,2.885 true 2.177,2.563 2.427,2.885 true 1.646,0.271 1.729,0.885 false 0.958,0.875 1.083,1.031 0.125,0.156 10 false D 1.448,1.104 1.573,1.26 0.125,0.156 10 false C 1.854,1.104 1.979,1.26 0.125,0.156 10 false B 2.365,0.875 2.49,1.031 0.125,0.156 10 false A 0.563,1.354 0.75,1.51 0.188,0.156 10 false *1 0.99,1.719 1.167,1.875 0.177,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.49 1.427,2.646 0.271,0.156 10 false K21 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCL- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCL+ 1.469,0.167 1.656,0.323 0.188,0.156 10 false *3 2.25,1.354 2.406,1.542 0.156,0.188 10 false *2

Disconnect the service wire from connector C.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (BCL+) - K21-2 (BCL-) Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

19.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

19.CHECK FLOOR WIRE (SHORT TO B+)
a.
U158373E02
2.031,2.563 1.75,2.885 true 2.177,2.563 2.427,2.885 true 1.646,0.271 1.729,0.885 false 0.958,0.875 1.083,1.031 0.125,0.156 10 false D 1.448,1.104 1.573,1.26 0.125,0.156 10 false C 1.854,1.104 1.979,1.26 0.125,0.156 10 false B 2.365,0.875 2.49,1.031 0.125,0.156 10 false A 0.563,1.354 0.75,1.51 0.188,0.156 10 false *1 0.99,1.719 1.167,1.875 0.177,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.49 1.427,2.646 0.271,0.156 10 false K21 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCL- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCL+ 1.469,0.167 1.656,0.323 0.188,0.156 10 false *3 2.25,1.354 2.406,1.542 0.156,0.188 10 false *2

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K21-1 (BCL+) - Body ground Ignition switch ON Below 1 V
K21-2 (BCL-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

20.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

20.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U158373E02
2.031,2.563 1.75,2.885 true 2.177,2.563 2.427,2.885 true 1.646,0.271 1.729,0.885 false 0.958,0.875 1.083,1.031 0.125,0.156 10 false D 1.448,1.104 1.573,1.26 0.125,0.156 10 false C 1.854,1.104 1.979,1.26 0.125,0.156 10 false B 2.365,0.875 2.49,1.031 0.125,0.156 10 false A 0.563,1.354 0.75,1.51 0.188,0.156 10 false *1 0.99,1.719 1.167,1.875 0.177,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.49 1.427,2.646 0.271,0.156 10 false K21 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCL- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCL+ 1.469,0.167 1.656,0.323 0.188,0.156 10 false *3 2.25,1.354 2.406,1.542 0.156,0.188 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K21-1 (BCL+) - Body ground Always 1 MΩ or higher
K21-2 (BCL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)



OK

21.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

21.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C249132E01
0.638,1.489 0.808,1.650 0.170,0.161 10 *1 1.727,1.579 1.897,1.740 0.170,0.161 10 *2

Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1647/82 is output. A
DTC B1642/81 is output. B
DTC B1642/81 or B1647/82 is not output. C

Text in Illustration
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

22.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH

B

C

22.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C166174E16
1.099,1.369 1.276,1.538 0.177,0.169 10 *1 2.194,1.369 2.366,1.538 0.172,0.169 10 *2

Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1642/81 or B1647/82 is not output. A
DTC B1647/82 is output. B
DTC B1642/81 is output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH

HINT:

Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

B

C