Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248351 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

When the No. 2 heater control sub-assembly (blower switch) is set to position 1 or higher, the contact of the heater blower motor relay assembly (HTR relay) relay is closed, current flows to the blower motor, and the blower motor operates. The blower motor speed can be changed by exchanging the ground and the blower resistor circuit with the No. 2 heater control sub-assembly (blower switch).

WIRING DIAGRAM

E231084E02
0.063,0.458 1.385,0.667 1.323,0.208 10 false from IG1 NO. 1 Relay 0.594,0.938 1.375,1.125 0.781,0.188 10 false from Battery 3.833,2.104 3.938,2.25 0.104,0.146 10 false 2 3.833,2.74 3.927,2.896 0.094,0.156 10 false 1 4.135,2.229 4.99,2.385 0.854,0.156 10 false F96*1, F35*2 4.135,2.396 5.344,2.719 1.208,0.323 10 false Blower Motor with Fan Sub-Assembly 5.875,1.24 6.146,1.396 0.271,0.156 10 false F41 2.042,0.615 2.292,0.76 0.25,0.146 10 false A/C 2.031,1.104 2.354,1.25 0.323,0.146 10 false HTR 2.99,1.479 3.302,1.625 0.313,0.146 10 false HTR 2.792,1.469 2.896,1.615 0.104,0.146 10 false 4 2.552,0.854 2.656,1.01 0.104,0.156 10 false 5 2.542,0.365 2.646,0.521 0.104,0.156 10 false 1 3.354,0.375 3.448,0.521 0.094,0.146 10 false 2 3.344,0.917 3.448,1.063 0.104,0.146 10 false 3 5.771,0.354 5.948,0.521 0.177,0.167 10 false 14 5.781,0.719 5.958,0.865 0.177,0.146 10 false 17 6.042,0.427 6.271,0.594 0.229,0.167 10 false HR 6.042,0.802 6.479,0.969 0.438,0.167 10 false SBLW 5.875,1.406 7.083,1.75 1.208,0.344 10 false Air Conditioning Amplifier Assembly 2.698,3.552 2.813,3.708 0.115,0.156 10 false 4 2.688,3.75 2.854,3.906 0.167,0.156 10 false HI 2.677,4.813 2.885,4.958 0.208,0.146 10 false M2 2.667,5.26 2.896,5.406 0.229,0.146 10 false M1 2.958,4.823 3.052,4.969 0.094,0.146 10 false 2 2.948,5.271 3.042,5.417 0.094,0.146 10 false 3 1.323,4.656 1.583,4.802 0.26,0.146 10 false F34 1.323,4.802 2.323,4.958 1,0.156 10 false Blower Resistor 4.052,6.323 4.313,6.469 0.26,0.146 10 false F39 4.052,6.479 6.281,6.813 2.229,0.333 10 false No. 2 Heater Control Sub-Assembly (Blower Switch) 6.469,6.323 6.563,6.469 0.094,0.146 10 false 5 5.073,3.615 5.177,3.76 0.104,0.146 10 false 7 5.427,3.615 5.521,3.76 0.094,0.146 10 false 6 5.76,3.615 5.938,3.76 0.177,0.146 10 false 10 6.156,3.615 6.25,3.76 0.094,0.146 10 false 9 4.917,4.073 5.135,4.229 0.219,0.156 10 false M1 5.292,4.083 5.51,4.229 0.219,0.146 10 false M2 5.646,4.083 5.802,4.229 0.156,0.146 10 false HI 6,4.083 6.208,4.229 0.208,0.146 10 false LO 6.365,4.083 6.479,4.229 0.115,0.146 10 false E 4.531,4.333 4.635,4.49 0.104,0.156 10 false 0 4.531,4.594 4.625,4.74 0.094,0.146 10 false 1 4.427,4.823 4.729,4.969 0.302,0.146 10 false 1 - 2 4.531,5.031 4.635,5.177 0.104,0.146 10 false 2 4.438,5.25 4.74,5.396 0.302,0.146 10 false 2 - 3 4.531,5.469 4.635,5.635 0.104,0.167 10 false 3 4.427,5.677 4.729,5.823 0.302,0.146 10 false 3 - 4 4.531,5.896 4.635,6.073 0.104,0.177 10 false 4 2.688,5.948 2.781,6.104 0.094,0.156 10 false 1 2.688,5.75 2.813,5.896 0.125,0.146 10 false E 0.156,6.74 2.427,6.958 2.271,0.219 10 false *1: w/ Fan Shroud Ventilation Duct 0.156,7.073 2.604,7.271 2.448,0.198 10 false *2: w/o Fan Shroud Ventilation Duct

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY)
a.

Inspect the heater blower motor relay assembly (HTR relay) (See page Vehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION).



OK

2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY)

2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Inspect the blower motor with fan sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) - BATTERY, IG1 NO. 1 RELAY AND BODY GROUND)

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) - BATTERY, IG1 NO. 1 RELAY AND BODY GROUND)
a.
E219629E01
0.09,0.06 0.260,0.221 0.170,0.161 10 *1

Remove the heater blower motor relay assembly (HTR relay).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
HTR-5 - Body ground Always 11 to 14 V
HTR-1 - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HTR-4 - Body ground Always Below 1 Ω


Text in Illustration
*1 Heater Blower Motor Relay Assembly (HTR Relay) Holder



OK

4.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the heater blower motor relay assembly (HTR relay).


b.

Disconnect the F41 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HTR-2 - F41-14 (HR) Always Below 1 Ω
HTR-2 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F39 No. 2 heater control sub-assembly (blower switch) connector.


b.

Disconnect the F41 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F39-9 (LO) - F41-17 (SBLW) Always Below 1 Ω
F39-9 (LO) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY))
U158664E02
0.688,0.948 0.948,1.125 0.26,0.177 10 false F96 0.094,0.094 0.26,0.281 0.167,0.188 10 false *a 0.74,0.708 0.906,0.865 0.167,0.156 10 false *A 0.865,2.219 1.031,2.375 0.167,0.156 10 false *B 0.833,2.469 1.094,2.646 0.26,0.177 10 false F35

a.

w/ Fan Shroud Ventilation Duct

i.

Disconnect the F96 blower motor with fan sub-assembly connector.



b.

w/o Fan Shroud Ventilation Duct

i.

Disconnect the F35 blower motor with fan sub-assembly connector.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Fan Shroud Ventilation Duct
Tester Connection Switch Condition Specified Condition
F96-2 - Body ground Ignition switch ON
Blower switch ON
11 to 14 V

w/o Fan Shroud Ventilation Duct
Tester Connection Switch Condition Specified Condition
F35-2 - Body ground Ignition switch ON
Blower switch ON
11 to 14 V


Text in Illustration
*A w/ Fan Shroud Ventilation Duct
*B w/o Fan Shroud Ventilation Duct
*a Front view of wire harness connector
(to Blower Motor with Fan Sub-Assembly)



OK

7.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BLOWER RESISTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BLOWER RESISTOR)
a.

w/ Fan Shroud Ventilation Duct

i.

Disconnect the F96 blower motor with fan sub-assembly connector.



b.

w/o Fan Shroud Ventilation Duct

i.

Disconnect the F35 blower motor with fan sub-assembly connector.



c.

Disconnect the F34 blower resistor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Fan Shroud Ventilation Duct
Tester Connection Condition Specified Condition
F96-1 - F34-4 (HI) Always Below 1 Ω
F96-1 - Body ground Always 10 kΩ or higher

w/o Fan Shroud Ventilation Duct
Tester Connection Condition Specified Condition
F35-1 - F34-4 (HI) Always Below 1 Ω
F35-1 - Body ground Always 10 kΩ or higher




OK

8.INSPECT BLOWER RESISTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BLOWER RESISTOR

OK

9.INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH)

NG

9.INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH)
a.

Inspect the No. 2 heater control sub-assembly (blower switch) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(for Manual Air Conditioning System)>INSPECTION).



OK

10.CHECK HARNESS AND CONNECTOR (NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) - BLOWER RESISTOR AND BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) - BLOWER RESISTOR AND BODY GROUND)
a.

Disconnect the F39 No. 2 heater control sub-assembly (blower switch) connector.


b.

Disconnect the F34 blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F39-5 (E) - F34-1 (E) Always Below 1 Ω
F39-6 (M2) - F34-2 (M2) Always Below 1 Ω
F39-7 (M1) - F34-3 (M1) Always Below 1 Ω
F39-10 (HI) - F34-4 (HI) Always Below 1 Ω
F39-5 (E) - Body ground Always Below 1 Ω
F39-6 (M2) - Body ground Always 10 kΩ or higher
F39-7 (M1) - Body ground Always 10 kΩ or higher
F39-10 (HI) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR