Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248387 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


PROCEDURE

Hide 62712 1.CLEAN QUARTER WINDOW GLASS

a.
B106929

Using a scraper, remove the adhesive sticking to the quarter window glass.

NOTICE:

Be careful not to damage the quarter window glass.



b.

Clean the outer edge of the quarter window glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Even if using a new glass, clean the glass with non-residue solvent.




Hide 62785A 2.INSTALL QUARTER WINDOW GLASS SPACER

a.

Using a brush or sponge, coat the application area of the quarter window glass spacer with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.
B284424E01
0.159,0.114 0.329,0.277 0.170,0.164 10 *a

Install 2 new quarter window glass spacers onto the glass, as shown in the illustration.

Text in Illustration
*a Back Side


Hide 62775B 3.INSTALL QUARTER WINDOW CLIP

a.

Using a brush or sponge, coat the application area of the quarter window clip with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.
B284425E01
0.175,0.16 0.357,0.324 0.181,0.165 10 *a

Install 3 new quarter window clips onto the quarter window glass, as shown in the illustration.

Text in Illustration
*a Back Side


Hide 75642E 4.INSTALL QUARTER WINDOW MOULDING

a.

Using a brush or sponge, coat the application area of the quarter window moulding with Primer G.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.
B284426E01
0.313,1.095 0.430,1.243 0.117,0.148 10 A 0.613,1.131 0.730,1.279 0.117,0.148 10 A 0.645,1.981 0.910,2.122 0.265,0.141 10 A-A 1.622,1.974 1.785,2.122 0.163,0.148 10 *a

Install new quarter window moulding onto the quarter window glass, as shown in the illustration.

Text in Illustration
*a 9.5 mm (0.374 in.)


Hide 62712 5.INSTALL QUARTER WINDOW GLASS

a.
B153152E01
0.249,0.812 0.418,0.967 0.169,0.155 10 *1 0.437,0.982 0.592,1.191 false 2.123,0.891 2.292,1.046 0.169,0.155 10 *1 2.311,1.062 2.457,1.298 false

Clean and shape the contact surface of the vehicle body.

Text in Illustration
*1 Adhesive

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.



b.
B284421E01
1.468,0.353 1.394,0.72 1.394,0.72 1.544,0.446 false 1.271,0.738 1.440,0.892 0.169,0.154 10 *a

Position the quarter window glass.

Text in Illustration
*a Mark

i.

Using suction cups, place the quarter window glass in the correct position.


ii.

Check that the whole contact surface of the quarter window glass rim is perfectly even.


iii.

Align the matchmarks on the quarter window glass and vehicle body.

NOTICE:

Check that the quarter window glass stoppers are attached to the vehicle body correctly.



iv.

Remove the quarter window glass.



c.
B271493E01
1.747,0.463 1.920,0.616 0.173,0.153 10 *1 1.769,1.515 1.942,1.667 0.173,0.153 10 *1 1.833,1.985 2.005,2.138 0.173,0.153 10 *2 3.009,0.488 3.182,0.640 0.173,0.153 10 *a 3.009,1.519 3.182,1.672 0.173,0.153 10 *b 1.94,0.586 2.276,0.861 false 1.962,1.634 2.272,1.8 false 2.025,2.051 2.228,1.918 false

Using a brush, coat the installation surface on the vehicle body with Primer M.

Text in Illustration
*1 Primer M
*2 Adhesive
*a Correct
*b Incorrect

NOTICE:
·

Do not coat the adhesive with Primer M.

·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Do not keep any of the opened Primer M for later use.




d.

Using a brush or sponge, coat the application areas that still have adhesive attached with Primer G.

B292046E01
0.448,2.531 0.752,2.706 0.304,0.175 10 : *1 0.13,0.083 0.351,0.271 0.221,0.189 10 *a 1.13,0.679 1.303,0.868 0.174,0.189 10 A 1.225,1.016 1.399,1.205 0.174,0.189 10 A 2.597,1.485 2.771,1.673 0.174,0.189 10 B 2.827,1.442 3.001,1.631 0.174,0.189 10 B 1.706,1.591 1.865,1.759 0.159,0.168 10 C 1.679,1.886 1.838,2.053 0.159,0.168 10 C 0.855,1.403 1.014,1.571 0.159,0.168 10 D 0.637,1.208 0.796,1.376 0.159,0.168 10 D 3.838,1.506 4.157,1.677 0.319,0.171 10 C-C 5.434,1.506 5.753,1.677 0.319,0.171 10 D-D 5.434,0.166 5.753,0.337 0.319,0.171 10 B-B 3.838,0.166 4.157,0.337 0.319,0.171 10 A-A 4.584,0.335 4.795,0.506 0.211,0.171 10 *b 4.689,0.692 4.900,0.863 0.211,0.171 10 *c 6.272,0.355 6.482,0.526 0.211,0.171 10 *e 5.71,0.355 5.921,0.526 0.211,0.171 10 *d 6.594,1.755 6.804,1.926 0.211,0.171 10 *g 6.543,2.176 6.753,2.347 0.211,0.171 10 *c 4.775,2.021 4.986,2.192 0.211,0.171 10 *c 4.848,2.416 5.058,2.587 0.211,0.171 10 *f

Text in Illustration
*1 Primer G - -
*a Back Side *b 6.4 mm (0.252 in.)
*c 14.0 mm (0.551 in.) *d 8.3 mm (0.327 in.)
*e 22.0 mm (0.866 in.) *f 6.0 mm (0.236 in.)
*g 6.5 mm (0.256 in.) - -

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



e.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut the tip off the cartridge nozzle.

HINT:

After cutting off the tip, use all adhesive within the time indicated in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.



f.

Apply adhesive to the quarter window glass, as shown in the illustration.

B292047E01
0.457,3.533 0.771,3.722 0.314,0.190 10 : *1 0.126,0.056 0.346,0.232 0.221,0.175 10 *a 1.637,1.078 1.858,1.253 0.221,0.175 10 *c 2.065,1.059 2.286,1.235 0.221,0.175 10 *b 3.027,0.862 3.248,1.038 0.221,0.175 10 *c 2.374,1.012 2.594,1.187 0.221,0.175 10 *b 1.245,1.986 1.417,2.175 0.173,0.190 10 A 1.32,2.32 1.492,2.510 0.173,0.190 10 A 2.689,2.795 2.861,2.985 0.173,0.190 10 B 2.922,2.751 3.094,2.941 0.173,0.190 10 B 1.806,2.918 1.978,3.107 0.173,0.190 10 C 1.779,3.191 1.951,3.381 0.173,0.190 10 C 0.949,2.719 1.121,2.909 0.173,0.190 10 D 0.731,2.527 0.904,2.716 0.173,0.190 10 D 4.783,1.037 5.003,1.213 0.221,0.175 10 *d 4.908,2.596 5.129,2.771 0.221,0.175 10 *g 6.19,0.738 6.410,0.913 0.221,0.175 10 *e 6.131,1.075 6.352,1.251 0.221,0.175 10 *f 6.66,2.519 6.881,2.694 0.221,0.175 10 *h 5.684,0.437 6.004,0.617 0.320,0.180 10 B-B 5.684,2.005 6.004,2.185 0.320,0.180 10 D-D 3.932,2.005 4.252,2.185 0.320,0.180 10 C-C 3.932,0.437 4.252,0.617 0.320,0.180 10 A-A

Text in Illustration
*1 Adhesive - -
*a Back Side *b 8.0 mm (0.315 in.)
*c 12.0 mm (0.472 in.) *d 13.4 mm (0.528 in.)
*e 23.3 mm (0.917 in.) *f 15.3 mm (0.602 in.)
*g 13.0 mm (0.512 in.) *h 13.5 mm (0.531 in.)


g.

Install the quarter window glass.

i.
B284421E01
1.468,0.353 1.394,0.72 1.394,0.72 1.544,0.446 false 1.271,0.738 1.440,0.892 0.169,0.154 10 *a

Using suction cups, position the quarter window glass so that the matchmarks are aligned, and press it in gently along the rim.

Text in Illustration
*a Mark

NOTICE:
·

Check that the quarter window glass clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and quarter window glass.




ii.

Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.


iii.

Lightly press the front surface of the glass to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22 lb) or more.



iv.
B149738E08
2.921,1.148 2.921,1.463 false 0.71,0.129 0.898,0.280 0.188,0.151 10 *1 0.999,1.488 1.187,1.645 0.188,0.158 10 *2 0.018,0.826 0.187,0.977 0.169,0.151 10 *3 1.116,1.142 1.116,1.458 false 2.497,0.129 2.685,0.280 0.188,0.151 10 *1 2.817,1.481 3.005,1.638 0.188,0.158 10 *2 1.971,0.69 2.137,0.841 0.166,0.151 10 *3 0.206,0.939 0.502,1.124 false 0.799,0.295 0.799,0.837 false 2.599,0.312 2.599,0.838 false 2.145,0.856 2.417,1.148 false

If necessary, use a scraper to correct the level or position of adhesive that has been applied.

Text in Illustration
*1 Quarter Window Glass
*2 Dam
*3 Adhesive

NOTICE:

Do not drive the vehicle within the time limits described in the table below.


Minimum time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 6.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 62452C 7.INSTALL REAR ROOF SIDE RAIL GARNISH

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 62472A 8.INSTALL ROOF SIDE INNER GARNISH

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 64740C 9.INSTALL DECK TRIM SIDE PANEL ASSEMBLY

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 73370 10.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 09113 12.INSTALL JACK HANDLE (for RH Side)

Hide 81250 13.INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 62412B 14.INSTALL CENTER PILLAR UPPER GARNISH

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 62520P 15.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 73202B 16.INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 62312B 17.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 67914 18.INSTALL FRONT DOOR SCUFF PLATE

HINT:

Use the same procedure as for the RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for 3 Door)>INSTALLATION).


Hide 19.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

Hide 20.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

Hide 21.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)