Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine fuel injection duration and to provide an appropriate air-fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A196093E06
1.948,1.563 1.5,0.417 1.5,0.417 1.375,0.417 false 2.229,1.552 2.458,0.969 2.458,0.969 2.583,0.969 false 4.646,1.385 4.333,2.198 4.333,2.198 4.208,2.198 false 4.948,1.667 5.135,2.135 5.135,2.135 5.26,2.135 false 0.073,0.323 1.354,0.656 1.281,0.333 10 false Temperature Sensor (Thermistor) 2.917,2.115 4.198,2.469 1.281,0.354 10 false Temperature Sensor (Thermistor) 2.01,0.01 2.219,0.167 0.208,0.156 10 false +B 2.25,0.542 3.354,0.698 1.104,0.156 10 false Power Transistor 2.625,0.885 3.813,1.208 1.188,0.323 10 false Platinum Hot Wire (Heater) 5.313,2.073 6.469,2.427 1.156,0.354 10 false Platinum Hot Wire (Heater) 2.99,1.74 3.958,1.958 0.969,0.219 10 false Output Voltage 1.708,1.479 1.865,1.677 0.156,0.198 10 false A 2.385,1.5 2.542,1.698 0.156,0.198 10 false B

DTC No. DTC Detection Condition Trouble Area
P0102 The mass air flow meter voltage is less than 0.2 V for 3 seconds.
(1 trip detection logic: Engine speed is less than 4000 rpm.)
(2 trip detection logic: Engine speed is 4000 rpm or more.)
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

No. 1 integration relay

·

ECM


P0103 The mass air flow meter voltage is more than 4.9 V for 3 seconds.
(1 trip detection logic: Engine speed is less than 4000 rpm.)
(2 trip detection logic: Engine speed is 4000 rpm or more.)
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

No. 1 integration relay

·

ECM



HINT:

When any of these DTCs are set, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores a DTC.

Example:

When the sensor output voltage remains less than 0.2 V, or higher than 4.9 V for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102 or P0103.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A283408E05
0.552,3.625 1.125,3.833 0.573,0.208 10 false Battery 1.646,1.875 2.302,2.063 0.656,0.188 10 false EFI MAIN 1.031,1.323 1.688,1.51 0.656,0.188 10 false EFI MAIN 2.375,1.313 3.031,1.5 0.656,0.188 10 false EFI NO.2 0.417,3.01 1.146,3.198 0.729,0.188 10 false MAIN 0.417,2.49 1.146,2.677 0.729,0.188 10 false R/I 1.292,2.156 2.771,2.365 1.479,0.208 10 false No. 1 Integration Relay 0.771,1.188 1.063,1.375 0.292,0.188 10 false 1C 3.125,1.188 3.417,1.375 0.292,0.188 10 false 1E 3.125,1.583 3.417,1.771 0.292,0.188 10 false 1D 0.771,1.573 1.063,1.76 0.292,0.188 10 false 1E 0.823,0.979 1.115,1.167 0.292,0.188 10 false 1 3.188,0.979 3.479,1.167 0.292,0.188 10 false 3 3.969,1.063 4.083,1.25 0.115,0.188 10 false 1 5.375,1.375 5.49,1.563 0.115,0.188 10 false 3 5.594,1.302 5.813,1.49 0.219,0.188 10 false 91 5.594,1.802 5.813,1.99 0.219,0.188 10 false 92 5.375,1.885 5.49,2.073 0.115,0.188 10 false 2 4.156,1.063 4.458,1.25 0.302,0.188 10 false +B 5.042,1.375 5.344,1.563 0.302,0.188 10 false VG 5.531,1.51 5.833,1.698 0.302,0.188 10 false B89 5.531,2.01 5.854,2.198 0.323,0.188 10 false B89 5.563,3.083 5.792,3.271 0.229,0.188 10 false 46 5.531,3.281 5.854,3.469 0.323,0.188 10 false A83 4.958,1.885 5.302,2.073 0.344,0.188 10 false E2G 5.875,1.385 6.177,1.573 0.302,0.188 10 false VG 5.875,1.885 6.229,2.083 0.354,0.198 10 false E2G 5.875,3.156 6.323,3.354 0.448,0.198 10 false MREL 6.292,3.74 6.719,3.927 0.427,0.188 10 false ECM 3.188,1.385 3.479,1.573 0.292,0.188 10 false 7 0.771,1.385 1.063,1.573 0.292,0.188 10 false 10 4.094,2.563 5.5,2.792 1.406,0.229 10 false Mass Air Flow Meter 4.094,2.396 4.385,2.594 0.292,0.198 10 false B72

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (DTC P0102 OR P0103)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)
a.
U126511C03
1.167,2.177 0.885,2.719 true 0.188,2.021 0.521,2.208 0.333,0.188 10 false B72 0.781,2.719 0.99,2.948 0.208,0.229 10 false +B 0.198,0.188 0.51,0.344 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B72-1 (+B) - Body ground Ignition switch ON 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect B72 the mass air flow meter connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-3 (VG) - B89-91 (VG) Always Below 1 Ω
B72-2 (E2G) - B89-92 (E2G) Always Below 1 Ω
B72-3 (VG) or B89-91 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION).


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).





OK

NG

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-2 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the B72 mass air flow meter connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-2 (E2G) - B89-92 (E2G) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the B72 mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-1 (+B) - 1E-3 Always Below 1 Ω
B72-1 (+B) or 1E-3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR