Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A357211E02
0.125,0.063 0.656,0.25 0.531,0.188 10 false Fig. 1: 0.115,0.333 0.979,0.542 0.865,0.208 10 false Resistance 0.313,0.604 0.698,0.792 0.385,0.188 10 false (kΩ) 0.156,0.76 0.385,0.938 0.229,0.177 10 false 30 0.156,0.979 0.375,1.146 0.219,0.167 10 false 20 0.177,1.292 0.396,1.458 0.219,0.167 10 false 10 0.25,1.667 0.396,1.854 0.146,0.188 10 false 5 0.25,1.906 0.375,2.083 0.125,0.177 10 false 3 0.26,2.135 0.385,2.313 0.125,0.177 10 false 2 0.25,2.448 0.385,2.625 0.135,0.177 10 false 1 0.135,3.635 0.406,3.802 0.271,0.167 10 false 0.1 0.115,3.281 0.375,3.448 0.26,0.167 10 false 0.2 0.115,3.083 0.375,3.25 0.26,0.167 10 false 0.3 0.115,2.833 0.375,3 0.26,0.167 10 false 0.5 0.458,4.01 0.729,4.177 0.271,0.167 10 false -20 0.927,4.01 1.198,4.177 0.271,0.167 10 false 0 1.26,4.01 1.49,4.188 0.229,0.177 10 false 20 1.635,4.01 1.865,4.188 0.229,0.177 10 false 40 2.021,4.01 2.25,4.188 0.229,0.177 10 false 60 2.417,4.021 2.646,4.198 0.229,0.177 10 false 80 2.771,4.021 3.042,4.198 0.271,0.177 10 false 100 3.073,4.01 3.385,4.219 0.313,0.208 10 false (°C) 0.521,4.167 0.792,4.333 0.271,0.167 10 false -4 0.896,4.156 1.167,4.323 0.271,0.167 10 false 32 1.26,4.167 1.531,4.333 0.271,0.167 10 false 68 1.604,4.167 1.917,4.333 0.313,0.167 10 false 104 1.979,4.167 2.292,4.333 0.313,0.167 10 false 140 2.375,4.188 2.688,4.354 0.313,0.167 10 false 176 2.781,4.188 3.094,4.354 0.313,0.167 10 false 212 3.083,4.198 3.396,4.406 0.313,0.208 10 false (°F) 1.531,4.354 2.396,4.563 0.865,0.208 10 false Temperature

The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0112 Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


P0113 Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM



HINT:

When any of these DTCs are set, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.

Example:

If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P0112.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0112 or P0113.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A391594E03
0.229,2.708 0.688,2.906 0.458,0.198 10 false B72 0.229,2.917 3.115,3.396 2.885,0.479 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 1.719,2.073 2.01,2.24 0.292,0.167 10 false E2 2.031,2.063 2.323,2.229 0.292,0.167 10 false 5 2.021,1.469 2.313,1.635 0.292,0.167 10 false 4 1.594,1.479 2.01,1.646 0.417,0.167 10 false THA 5.438,1.479 5.854,1.646 0.417,0.167 10 false THA 5.438,2.083 6.021,2.25 0.583,0.167 10 false ETHA 5.146,1.479 5.438,1.646 0.292,0.167 10 false 90 5.083,2.083 5.458,2.25 0.375,0.167 10 false 122 5.948,3.094 6.323,3.26 0.375,0.167 10 false B89 5.927,3.281 6.427,3.448 0.5,0.167 10 false ECM 6.01,1.365 6.51,1.531 0.5,0.167 10 false R 6.052,1.073 6.552,1.24 0.5,0.167 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


e.

Read the value displayed on the GTS.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
Same as actual intake air temperature C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter connector.

U126507C02
5.417,1.719 4.917,2.083 true 5.677,1.719 5.844,2.052 true 0.854,1.865 1.052,2.042 0.198,0.177 10 false *1 3.99,0.323 4.188,0.5 0.198,0.177 10 false *a 4.146,1.563 4.469,1.75 0.323,0.188 10 false B72 4.563,2.042 4.906,2.229 0.344,0.188 10 false THA 5.896,2.021 6.24,2.208 0.344,0.188 10 false E2 2.698,1.865 2.896,2.042 0.198,0.177 10 false *2 2.438,1.021 2.781,1.208 0.344,0.188 10 false THA 2.427,1.333 2.906,1.521 0.479,0.188 10 false ETHA
*1 Mass Air Flow Meter *2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)
- -



b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F)


HINT:

Perform "Inspection After Repairs" after replacing the mass air flow meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the B72 mass air flow meter connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-4 (THA) - B89-90 (THA) Always Below 1 Ω
B72-5 (E2) - B89-122 (ETHA) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255925C67
0.662,0.158 0.817,0.311 0.155,0.154 10 *1 2.57,0.158 2.725,0.311 0.155,0.154 10 *2 2.226,0.805 2.525,0.958 0.299,0.154 10 THA 2.226,1.183 2.615,1.336 0.389,0.154 10 ETHA
*1 Mass Air Flow Meter
*2 ECM


Disconnect the mass air flow meter connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repairs" after replacing the mass air flow meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the B72 mass air flow meter connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B72-4 (THA) or B89-90 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR