Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

These DTCs relate to the throttle position sensor.

The throttle position sensor is mounted on the throttle body with motor assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme conditions.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

U158091E02
5.052,2.125 5.052,1.833 false 4.198,1.063 4.323,0.604 false 4.323,0.604 4.448,0.604 false 1.021,2.156 0.729,1.01 false 1.042,2.583 1.854,1.323 false 1.021,2.958 0.5,3.542 false 1.021,3.333 1.552,3.708 false 4.729,2.333 4.958,2.49 false 4.667,1.427 4.948,1.635 false 5.063,1.917 5.427,2.208 false 5.563,0.177 5.667,0.177 false 5.667,0.177 5.906,1.438 false 3.667,1.188 4.021,1.365 0.354,0.177 10 false 4.65 5.479,2.198 5.938,2.417 0.458,0.219 10 false 1.11 V 4.26,1.313 4.708,1.5 0.448,0.188 10 false VTA2 2.427,0.531 4.135,0.76 1.708,0.229 10 false Sensor Output Voltage (V) 4.5,0.5 5.74,0.729 1.24,0.229 10 false Fail-safe Angle 4.188,3.583 6.594,3.781 2.406,0.198 10 false Throttle Valve Opening Angle (°) 3.615,1.875 4.031,2.052 0.417,0.177 10 false *2.55 3.625,2.385 4.063,2.583 0.438,0.198 10 false *0.93 3.667,2.031 4.104,2.229 0.438,0.198 10 false 2.25 3.677,2.542 4.021,2.74 0.344,0.198 10 false 0.69 5.01,2.427 5.469,2.646 0.458,0.219 10 false VTA1 4.771,3.208 5.917,3.406 1.146,0.198 10 false Usable Range 3.979,3.26 4.333,3.458 0.354,0.198 10 false 0 4.167,2.844 4.313,3.042 0.146,0.198 10 false 6 6.25,3.271 6.635,3.469 0.385,0.198 10 false 84 0.063,4.385 0.573,4.583 0.51,0.198 10 false Note: 0.063,4.708 3.573,5.073 3.51,0.365 10 false The throttle valve opening angle detected by the sensor terminal VTA1 is expressed as a percentage. 0.063,5.438 3.26,5.667 3.198,0.229 10 false Between 10% and 22%: Throttle valve fully closed 0.063,5.781 3.167,6.01 3.104,0.229 10 false Between 64% and 96%: Throttle valve fully open 0.063,6.167 3.063,6.396 3,0.229 10 false Approximately 18.6%: Fail safe angle (6°) 0.208,0.906 0.844,1.188 0.635,0.281 10 false Magnet 0.073,4.052 1.594,4.417 1.521,0.365 10 false Throttle Position Sensor 1.583,3.656 2.094,3.854 0.51,0.198 10 false Magnet 1.906,1.125 2.542,1.344 0.635,0.219 10 false IC No. 1 0.292,3.583 0.927,3.802 0.635,0.219 10 false IC No. 2 2.396,4.052 2.906,4.25 0.51,0.198 10 false ECM 1.708,2.021 2.156,2.219 0.448,0.198 10 false VCTA 1.813,3.115 2.167,3.333 0.354,0.219 10 false ETA 1.74,2.375 2.198,2.594 0.458,0.219 10 false VTA1 1.74,2.75 2.198,2.969 0.458,0.219 10 false VTA2 4.146,3.938 5.74,4.135 1.594,0.198 10 false *: During fail-safe control 3.833,5.479 7.083,5.656 3.25,0.177 10 false VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V 3.833,5.135 5.885,5.333 2.052,0.198 10 false Characteristics of sensor output: 3.875,0.094 5.563,0.302 1.688,0.208 10 false Line indicating VTA2 x 0.8 3.76,0.979 4.021,1.177 0.26,0.198 10 false 5.0

DTC No. DTC Detection Condition Trouble Area
P0120 Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


P0121 Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


P0122 Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VCTA circuit

·

ECM


P0123 Output voltage of VTA1 is 4.535 V or more for 2 seconds or more when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA1 circuits

·

ECM


P0220 Output voltage of VTA2 quickly fluctuates beyond both lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


P0222 Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VCTA circuit

·

ECM


P0223 Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the accelerator pedal is depressed
(1 trip detection logic)
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA2 circuits

·

ECM


P2135 Either of the following conditions is met (1 trip detection logic):
(a) Difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM



HINT:
·

When any of these DTCs are stored, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.


·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

Reference (Normal Condition)
GTS Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No. 2 2.1 to 3.1 V 4.6 to 5.0 V



MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm that the throttle position sensor is operating properly.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor and stores a DTC.


P0121

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm that the throttle position sensor and VTA1 are operating properly.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor. The ECM illuminates the MIL and stores the DTC.


MONITOR STRATEGY

Frequency of operation Continuous

CONFIRMATION DRIVING PATTERN

A198824E96
3.688,1.396 3.323,0.406 3.323,0.406 3.552,0.406 false 2.646,1.979 2.375,1.208 2.375,1.208 2.542,1.208 false 4.927,1.99 5.271,1.104 5.271,1.104 5.375,1.104 false 1.229,1.875 1.625,2.094 0.396,0.219 10 false Idling 0.417,2.146 1.635,2.323 1.219,0.177 10 false Ignition Switch ON 2.094,2.052 2.354,2.25 0.26,0.198 10 false [A] 3.844,1.76 4.031,1.948 0.188,0.188 10 false [B] 5.438,1.031 6.073,1.177 0.635,0.146 10 false Released 3.625,0.313 4.354,0.458 0.729,0.146 10 false Depressed 4.375,2.635 5.073,2.823 0.698,0.188 10 false 2 seconds 4.708,1.719 4.948,1.927 0.24,0.208 10 false [C] 5.031,2.969 5.302,3.167 0.271,0.198 10 false [D] 2.583,1.135 3.219,1.281 0.635,0.146 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress and release the accelerator pedal [B].

8.

Idle the engine for 2 seconds or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.




FAIL-SAFE

When any of these DTCs as well as other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A254078E08
5.573,1.042 5.958,1.188 0.385,0.146 10 false VCTA 5.583,0.479 5.979,0.646 0.396,0.167 10 false VTA1 5.583,1.573 5.958,1.75 0.375,0.177 10 false VTA2 5.604,2.146 5.896,2.302 0.292,0.156 10 false ETA 1.615,0.438 1.927,0.594 0.313,0.156 10 false VTA 1.542,1.531 1.917,1.688 0.375,0.156 10 false VTA2 5.25,0.583 5.583,0.75 0.333,0.167 10 false B89 5.25,2.24 5.583,2.406 0.333,0.167 10 false B89 5.25,1.656 5.573,1.833 0.323,0.177 10 false B89 5.24,1.125 5.51,1.292 0.271,0.167 10 false B89 1.688,0.979 1.927,1.146 0.24,0.167 10 false VC 1.708,2.104 1.927,2.271 0.219,0.167 10 false E2 1.052,0.698 1.292,0.844 0.24,0.146 10 false IC1 1.042,1.573 1.313,1.719 0.271,0.146 10 false IC2 2.01,0.979 2.115,1.135 0.104,0.156 10 false 5 2,0.438 2.135,0.604 0.135,0.167 10 false 6 2.021,2.104 2.125,2.25 0.104,0.146 10 false 3 5.26,0.958 5.615,1.125 0.354,0.167 10 false 115 5.313,0.396 5.573,0.563 0.26,0.167 10 false 84 5.292,1.49 5.552,1.635 0.26,0.146 10 false 83 5.25,2.073 5.594,2.229 0.344,0.156 10 false 116 2.021,1.531 2.135,1.688 0.115,0.156 10 false 4 0.406,2.938 0.688,3.083 0.281,0.146 10 false B29 0.406,3.104 2.844,3.313 2.438,0.208 10 false Throttle Body with Motor Assembly 6.031,2.865 6.385,3.021 0.354,0.156 10 false ECM 6.469,1 6.708,1.146 0.24,0.146 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.


e.

Read the values displayed on the GTS.

Result
When Accelerator Pedal Released When Accelerator Pedal Depressed Trouble Area Proceed to
Throttle Position No. 1 Throttle Position No. 2 Throttle Position No. 1 Throttle Position No. 2
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VCTA circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V ETA circuit open
0 to 0.2 V,
or 4.5 to 5.0 V
2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V,
or 4.5 to 5.0 V
VTA2 circuit open or ground short
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
Throttle position sensor circuit normal B

HINT:
·

DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the Freeze Frame Data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Calculate the voltage of VTA and VTA2 according to Throttle Sensor Volt % and Throttle Sensor #2 Volt % respectively and confirm their consistency.

Example:

Throttle Sensor Volt % / 100 (%) x 5 (V) = Throttle Position No.1


Characteristics Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle position No. 1

VTA2: Throttle position No. 2


·

If DTC P0121 is output, proceed to the "Check Harness and Connector (Throttle Position Sensor - ECM)".





A

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the B29 throttle body with motor assembly connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B29-5 (VC) - B89-115 (VCTA) Always Below 1 Ω
B29-6 (VTA) - B89-84 (VTA1) Always Below 1 Ω
B29-4 (VTA2) - B89-83 (VTA2) Always Below 1 Ω
B29-3 (E2) - B89-116 (ETA) Always Below 1 Ω
B29-5 (VC) or B89-115 (VCTA) - Body ground Always 10 kΩ or higher
B29-6 (VTA) or B89-84 (VTA1) - Body ground Always 10 kΩ or higher
B29-4 (VTA2) or B89-83 (VTA2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
U126154C01
0.938,1.729 1.656,1.406 true 2.667,1.729 1.938,1.406 true 0.198,0.146 0.448,0.354 0.25,0.208 10 false *a 0.677,1.635 0.906,1.802 0.229,0.167 10 false E2 2.719,1.635 2.948,1.802 0.229,0.167 10 false VC 1.573,0.51 1.875,0.688 0.302,0.177 10 false B29
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B29-5 (VC) - B29-3 (E2) Ignition switch ON 4.5 to 5.5 V




OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine.


f.

With the vehicle stationary, fully depress and release the accelerator pedal.


g.

Idle the engine for 2 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output A
DTC is not output B



A

B

END