The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed to the cylinder head. When the camshaft rotates, each of 3 teeth on the camshaft passes the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0340 | When one of following conditions is met:
·
No camshaft position sensor signal to ECM while cranking (2 trip detection logic) ·
Camshaft/Crankshaft misalignment detected at engine speed of 600 rpm or more (1 trip detection logic) |
·
Open or short in camshaft position sensor circuit ·
Camshaft position sensor ·
Intake camshaft ·
Jumped tooth of timing chain ·
ECM |
DTC P0340 indicates a malfunction relating to the camshaft position sensor circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).
Reference: Inspection using an oscilloscope (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0335).
If no signal is transmitted by the camshaft position sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Wait 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0340.
Check DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.
Refer to DTC P0335 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0335).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P0340 is output | A |
| DTC P0340 and other DTCs are output | B |
If any DTCs other than P0340 are output, troubleshoot those DTCs first.
A
B
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Inspect the camshaft position sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>INSPECTION).
OK
NG
Disconnect the B30 camshaft position sensor connector.
Disconnect the B89 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B30-1 - B89-82 (VV1+) | Always | Below 1 Ω |
| B30-2 - B89-114 (VV1-) | Always | Below 1 Ω |
| B30-1 or B89-82 (VV1+) - Body ground | Always | 10 kΩ or higher |
| B30-2 or B89-114 (VV1-) - Body ground | Always | 10 kΩ or higher |
OK
NG
| *a | OK |
| *b | NG |
| *c | Clearance |
Check the camshaft position sensor installation.
Sensor is installed correctly.
OK
NG
OK
NG
Inspect the timing rotor of the intake camshaft.
Camshaft timing rotor does not have any cracks or deformation.
OK
NG
Replace the camshaft position sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear DTCs (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Idle the engine for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC P0340 is output | A |
| DTC is not output | B |
If the engine does not start, replace the ECM.
A
B