| Cruise control main switch cannot be turned on (Cruise control indicator in combination meter does not illuminate)
|
Cruise control switch circuit
|
( )
|
| Cruise main indicator light circuit
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| SET does not operate or CANCEL operates when it should not (DTC is not output)
|
Cruise control switch circuit
|
( )
|
| Clutch switch circuit*2
|
( )
|
| Automatic transaxle system (U340E)*1
|
( )
|
| Automatic transaxle system (U441E)*1
|
( )
|
| Anti-lock brake system*3
|
( )
|
| Vehicle stability control system (for Separate Type Yaw Rate Sensor)*4
|
( )
|
| Vehicle stability control system (for Built-in Type Yaw Rate Sensor)*4
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Actual vehicle speed deviates above or below set speed
|
Anti-lock brake system*3
|
( )
|
| Vehicle stability control system (for Separate Type Yaw Rate Sensor)*4
|
( )
|
| Vehicle stability control system (for Built-in Type Yaw Rate Sensor)*4
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Cruise control is not canceled when brake pedal is depressed
|
Stop light switch circuit
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Moving shift lever does not cancel cruise control*1
|
Automatic transaxle system (U340E)*1
|
( )
|
| Automatic transaxle system (U441E)*1
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Cruise control is not canceled when clutch pedal is depressed*2
|
Clutch switch circuit*2
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Control switch does not operate (-SET, +RES, CANCEL not possible)
|
Cruise control switch circuit
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| SET is possible at less than approximately 40 km/h (25 mph), or CANCEL does not operate
|
Anti-lock brake system*3
|
( )
|
| Vehicle stability control system (for Separate Type Yaw Rate Sensor)*4
|
( )
|
| Vehicle stability control system (for Built-in Type Yaw Rate Sensor)*4
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Poor response in ACCEL and RESUME modes
|
Cruise control switch circuit
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| DTC memory is cleared
|
ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| DTC is not output or is output when it should not be
|
TC and CG terminal circuit
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Cruise control indicator light does not illuminate
|
Cruise control switch circuit
|
( )
|
| Cruise main indicator circuit
|
( )
|
| Combination meter assembly
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|
| Cruise control SET indicator does not illuminate (SET function operates normally)
|
Cruise SET indicator light circuit
|
( )
|
| Combination meter assembly
|
( )
|
| ECM (for 2NZ-FE)
|
( )
|
| ECM (for 1NZ-FE)
|
( )
|