1.PERFORM SPARK TEST
Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
Check for DTCs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR
If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.
Remove the 4 ignition coils and 4 spark plugs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.
Arrange the removed parts in the correct order.
Disconnect the 4 injector connectors.
Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.
Install a spark plug to each No. 1 ignition coil and connect the No. 1 ignition coil connectors.
Ground the spark plugs.
Check that spark occurs while the engine is being cranked.
Check whether sparks occur.
Ground the spark plugs when checking them.
Replace any ignition coils that have been subjected to a physical impact.
Do not crank the engine for more than 2 seconds.
If the spark plug is struck or dropped, replace it.
If spark does not occur, perform the following procedure.
Install the 4 spark plugs and 4 No. 1 ignition coils.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.
Install the same parts to their original positions.
Check for DTCs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR
2.INSPECT IGNITION COIL AND SPARK TEST
Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
Perform the spark test in accordance with the following procedure.
Check that the wire harness side connector of the No. 1 ignition coil is securely connected.
| Result | Proceed to |
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each No. 1 ignition coil.
If there is a cylinder where sparks do not occur, replace its ignition coil with the No. 1 ignition coil of a cylinder where sparks occur normally.
Perform a spark test on each spark plug.
If there is a cylinder where sparks do not occur, replace its spark plug with the spark plug of a cylinder where sparks occur normally.
Connect the 4 injector connectors.
Install the No. 1 ignition coil and spark plugs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.
Install the same parts to their original positions.
Check for DTCs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DTC CHECK / CLEAR
19100P
3.INSPECT SPARK PLUG
Be careful not to damage the iridium tip or platinum tip of the spark plug.
Check the iridium tip visually as it is easily damaged.
Never attempt to adjust the electrode gap of a used spark plug.
If the spark plug is extremely dirty with oil, etc., replace it.
Replace a spark plug if it is damaged at all.
When installing a new spark plug, do not remove the protective cap from the spark plug tip until just before installing the spark plug to the engine.
If the spark plug has been struck or dropped, replace it.
Perform "Inspection After Repair" after replacing a spark plug.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
| *1 | Ground |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Spark plug (Terminal part) - Ground | Always | 10 MΩ or higher |
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Start the engine.
Quickly accelerate the engine to 4000 rpm 5 times.
When DTC P0300 (Random / Multiple Cylinder Misfire Detected) or related DTCs are output, do not perform this step.
Remove the spark plug.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its thread and insulator.
If there is any damage, replace the spark plug.
| Manufacturer | Product |
|---|---|
| DENSO | SK16R11 |
| NGK | IFR5A11 |
| *a | Electrode Gap |
Check the spark plug electrode gap.
1.3 mm (0.0512 in.)
If the electrode gap is more than the maximum, replace the spark plug.
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
Never attempt to adjust the electrode gap of a used spark plug.
Install the 4 spark plugs.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
4.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION