Home › Engine / Hybrid System › 2NZ-FE COOLING › COOLING FAN SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051459 2NZ-FE COOLING _0248129 COOLING FAN SYSTEM J

2NZ-FE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


TECHNICAL DESCRIPTION

To control the cooling fans, the ECM turns on or off the cooling fan relays based on the engine coolant temperature, air conditioning switch, refrigerant pressure, engine speed and vehicle speed signals.

The ECM turns on or off the fan relays to switch the cooling fan motor circuit between the series circuit and parallel circuit, controlling the cooling fan motor speed in 2 steps.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FAN NO. 1 RELAY (POWER SOURCE)
a.
A247838E01
0.12,0.039 0.310,0.245 0.190,0.206 10 *1 0.22,1.94 0.410,2.145 0.190,0.206 10 *2

Remove the FAN No. 1 relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FAN No. 1 relay holder 3 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Holder


c.

Reinstall the FAN No. 1 relay.



OK

2.CHECK ENGINE ROOM RELAY BLOCK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK ENGINE ROOM RELAY BLOCK
a.
A247839E05
0.177,0.115 0.365,0.323 0.188,0.208 10 false *1 0.25,3.323 0.438,3.531 0.188,0.208 10 false *2 1.281,0.177 1.469,0.385 0.188,0.208 10 false *3

Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.


b.

Turn the Ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FAN No. 1 relay holder 1 - Body ground Ignition switch ON 11 to 14 V
FAN No. 2 relay holder 2 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Holder
*3 FAN No. 2 Relay Holder


d.

Reinstall the FAN No. 1 relay and FAN No. 2 relay.



OK

3.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FAN NO. 1 RELAY
a.


OK

4.INSPECT FAN NO. 2 RELAY

NG

REPLACE FAN NO. 1 RELAY

4.INSPECT FAN NO. 2 RELAY
a.


OK

5.INSPECT COOLING FAN RESISTOR

NG

REPLACE FAN NO. 2 RELAY

5.INSPECT COOLING FAN RESISTOR

OK

6.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

NG

REPLACE COOLING FAN RESISTOR

6.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
a.

Remove the FAN No. 2 relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FAN No. 2 relay holder 5 - Body ground Always Below 1 Ω



c.

Reinstall the FAN No. 2 relay.



OK

7.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COOLING FAN RESISTOR - BODY GROUND)
a.

Disconnect the cooling fan resistor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-1 (-) - Body ground Always Below 1 Ω



c.

Connect the cooling fan resistor connector.



OK

8.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - COOLING FAN RESISTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - COOLING FAN RESISTOR)
a.

Disconnect the cooling fan resistor connector.


b.

Remove the FAN No. 2 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
FAN No. 2 relay holder 4 - A22-2 (+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-2 (+) or FAN No. 2 relay holder 4 - Body ground Always 10 kΩ or higher


d.

Reinstall the FAN No. 2 relay.


e.

Reconnect the cooling fan resistor connector.



OK

9.CHECK COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK COOLING FAN MOTOR

OK

10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 1 RELAY)

NG

10.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 1 RELAY)
a.

Disconnect the cooling fan motor connector.


b.

Remove the FAN No. 1 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A21-2 - FAN No. 1 relay holder 5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A21-2 or FAN No. 1 relay holder 5 - Body ground Always 10 kΩ or higher



d.

Reinstall the FAN No. 1 relay.


e.

Reconnect the cooling fan motor connector.



OK

11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - FAN NO. 2 RELAY)
a.

Disconnect the cooling fan motor connector.


b.

Remove the FAN No. 2 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A21-1 - FAN No. 2 relay holder 3 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A21-1 or FAN No. 2 relay holder 3 - Body ground Always 10 kΩ or higher



d.

Reinstall the FAN No. 2 relay.


e.

Reconnect the cooling fan motor connector.



OK

12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM)
a.

Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A83-8 (FANH) - FAN No. 2 relay holder 1 Always Below 1 Ω
A83-7 (FANL) - FAN No. 1 relay holder 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A83-8 (FANH) or FAN No. 2 relay holder 1 - Body ground Always 10 kΩ or higher
A83-7 (FANL) or FAN No. 1 relay holder 2 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the FAN No. 1 relay and FAN No. 2 relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR