Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2016.09
RM19S0E _59 Vehicle Exterior _051502 DOOR / HATCH _0248392 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


PROCEDURE

Hide 75921C 1.INSTALL NO. 1 BLACK OUT TAPE

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>INSTALLATION)


Hide 67001A 2.INSTALL FRONT DOOR PANEL CUSHION

a.
B271614

Install the 2 front door panel cushions.


Hide 67861 3.INSTALL FRONT DOOR WEATHERSTRIP

a.
B271613

Engage the 29 clips to install the front door weatherstrip.


b.

Install the clip.


Hide 68610B 4.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.
B271610

Install the front door check assembly to the door panel with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the front door check assembly to the body panel with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69311A 5.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B372732E02
2.198,0.76 2.5,0.323 false 1.156,2.271 1.302,2.448 0.146,0.177 10 false 1 0.427,2.292 0.573,2.469 0.146,0.177 10 true 2 2.531,0.198 2.729,0.375 0.198,0.177 10 false *a

Engage the snap to install the front door lock open rod as indicated by the arrows in the order shown in the illustration.

Text in Illustration
*a Snap


Hide 69201A 6.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door outside handle frame sub-assembly.


b.
B373459

Engage the 2 guides and grommet to install front door outside handle frame sub-assembly as shown in the illustration.


c.
B271625

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242E 7.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B271620

Engage the 2 claws to install the front door outside handle rear pad.


Hide 69241H 8.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B271619

Engage the 3 claws to install the front door outside handle front pad.


Hide 69210 9.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B271618

Install the front door outside handle assembly as shown in the illustration.


Hide 69310 10.INSTALL FRONT DOOR LOCK ASSEMBLY

Hide 69217E 11.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.
B271703

Engage the 2 guides and claw to install the front door outside handle cover.


b.
B271615

Install the front door outside handle cover with lock cylinder.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Install the hole plug.


Hide 68215 12.INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP

a.
B377919

Install the front door fix window weatherstrip to the front door fix window glass.


Hide 68125 13.INSTALL FRONT DOOR FIX WINDOW GLASS

a.
B271612

Install the front door fix window glass with front door fix window weatherstrip as shown in the illustration.


Hide 67401F 14.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B271609

Install the front door front lower frame sub-assembly with the screw.

NOTICE:

Make sure to return the front door weatherstrip to its original condition after performing this step.


HINT:

Peel back the front door weatherstrip to install the screw.



b.

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 67403F 15.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B271608

Engage the guide.


b.

Install the front door rear lower frame sub-assembly with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68141C 16.INSTALL FRONT DOOR GLASS RUN

a.
B271607

Install the front door glass run.


Hide 69801 17.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator sub-assembly.


b.

Temporarily Install the temporary bolt.


c.
B312391E01
1.141,0.137 1.257,0.289 0.116,0.152 10 2 1.787,0.431 1.902,0.584 0.116,0.152 10 4 1.098,1.498 1.214,1.650 0.116,0.152 10 1 0.734,1.454 0.849,1.606 0.116,0.152 10 3 1.549,0.047 1.723,0.200 0.174,0.152 10 *a 1.537,0.141 1.438,0.777 false

Insert the front door window regulator sub-assembly into the door panel. Use the temporary bolt to hang the front door window regulator sub-assembly on the door panel.

Text in Illustration
*a Temporary Bolt


d.

Tighten the 3 bolts and temporary bolt in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the front door window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the connector.


Hide 68101 18.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the power window regulator master switch and move the front door glass so that the door glass bolt holes can be seen.


c.

Disconnect the cable from the negative (-) battery terminal and the power window regulator master switch.


d.
B372733E01
0.969,0.479 1.125,0.677 0.156,0.198 10 false 1 1.833,0.063 1.99,0.26 0.156,0.198 10 false 2

Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



e.
B271602

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.
B271601

Install the front door service hole cover.


Hide 67831 19.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply butyl tape to the front door panel.


b.

Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through a new front door service hole cover.


c.
B271702E01
0.119,0.293 0.269,0.446 0.150,0.153 10 *a 0.291,0.392 0.412,0.524 false 3.166,0.261 3.316,0.414 0.150,0.153 10 *a 3.02,3.11 3.170,3.263 0.150,0.153 10 *a 2.883,3.096 3.012,3.208 false 2.998,0.46 3.161,0.362 false

Install a new front door service hole cover according to the reference points on the front door panel.

Text in Illustration
*a Reference Point

HINT:

Securely install the front door service hole cover taking care to prevent wrinkles.



Hide 68160C 21.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>INSTALLATION).


Hide 87910 22.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSTALLATION).


Hide 75751C 23.INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

Hide 68171B 24.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B370698

Engage the 7 claws to install the front door glass inner weatherstrip as shown in the illustration.


Hide 69205 25.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B373463

Engage the 4 guides to install the front door inside handle sub-assembly.


Hide 67601 26.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B373462E02
1.25,0.938 1.073,0.469 false 1.177,1.458 1.302,1.292 false 0.844,0.313 1.031,0.51 0.188,0.198 10 true *1 0.958,1.479 1.135,1.698 0.177,0.219 10 true *2

Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.

Text in Illustration
*1 Front Door Lock Remote Control Cable Assembly
*2 Front Door Inside Locking Cable Assembly


b.
B369625

Engage the 7 clips to install the front door trim board sub-assembly.


c.
B377918

Install the 3 screws.


d.
B377917

Engage the claw to close the cover.


Hide 74231 27.INSTALL FRONT ARMREST BASE UPPER PANEL

a.

Connect the connector.


b.
B377915

Engage the 9 claws and 4 guides to install the front armrest base upper panel.


Hide 28.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION