Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

The VVT system includes the ECM, camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E34
4.483,0.815 6.151,0.978 1.668,0.163 10 Camshaft Position Sensor 4.483,1.325 6.216,1.485 1.733,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 4.441,3.922 2.842,0.174 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty Cycle 4.483,1.827 5.808,1.981 1.325,0.154 10 Mass Air Flow Meter 4.483,2.854 6.827,3.042 2.344,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.031,2.511 1.547,0.167 10 Throttle Position Sensor 4.483,3.353 5.938,3.506 1.455,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 6.931,4.527 3.272,0.310 10 VVT Controller (Camshaft Timing Gear Assembly) 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0011 Valve timing is not adjusted in valve timing advance range
(1 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


P0012 Valve timing is not adjusted in valve timing retard range
(2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM



MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller being stuck and stores a DTC.


Example:

A DTC is stored when the following conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After the above condition 1 is met, the camshaft timing oil control valve is forcibly activated for 60 seconds.


These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve assembly malfunctions or the presence of foreign objects in the camshaft timing oil control valve assembly.


MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing oil control valve assembly and camshaft timing gear assembly
Required Sensors/Components (Related) Camshaft position sensor, camshaft position sensor and engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232050E10
1.361,2.351 1.596,2.498 0.235,0.147 10 [A] 1.88,2.062 2.114,2.208 0.235,0.147 10 [B] 3.012,1.001 3.247,1.148 0.235,0.147 10 [C] 4.049,2.316 4.284,2.463 0.235,0.147 10 [D] 4.285,3.14 4.519,3.287 0.235,0.147 10 [E] 5.445,2.218 5.680,2.365 0.235,0.147 10 [F]* 6.618,2.3 6.852,2.446 0.235,0.147 10 [G] 6.832,3.154 7.067,3.301 0.235,0.147 10 [H] 0.133,2.309 1.104,2.641 0.971,0.332 10 Ignition Switch ON 0.712,2.057 1.099,2.241 0.387,0.184 10 Idling 0.027,1.09 1.145,1.434 1.119,0.343 10 Approximately 60 km/h (37 mph) 0.17,0.376 1.123,0.541 0.952,0.165 10 Vehicle Speed 1.618,2.767 2.422,2.960 0.804,0.193 10 Warming up 2.561,2.776 3.805,2.923 1.244,0.147 10 10 minutes or more 2.552,3.393 3.847,3.567 1.295,0.174 10 3 minutes or more 6.723,2.596 6.33,3.458 6.33,3.458 6.246,3.458 false 4.159,2.617 3.836,3.479 3.836,3.479 3.766,3.479 false 2.379,0.025 7.035,0.542 4.656,0.517 10 *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5.004,3.379 6.195,3.553 1.191,0.174 10 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0011 or P0012.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain store even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P0011 or P0012 is output A
DTC P0011 or P0012 and other DTCs are output B

HINT:

If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Turn the A/C on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).


g.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

4.CHECK VALVE TIMING
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Turn the ignition switch off and wait for at least 30 seconds.



f.

Start the engine and warm it up.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Read the output pending DTCs using the GTS.

OK:

No pending DTC output.




OK

NG

4.CHECK VALVE TIMING
4.CHECK VALVE TIMING
a.
A369443C01
1.135,0.906 0.906,2.083 0.906,2.083 2.156,1.25 true 2.177,3.448 2.177,4.26 true 0.823,2.115 1.135,2.313 0.313,0.198 10 false *a 2.115,4.302 2.427,4.5 0.313,0.198 10 false *b
*a Timing Marks (at top center of each gear)
*b Timing Mark (groove on crankshaft pulley)


Remove the cylinder head cover.


b.

Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.


c.

Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.


If not, turn the crankshaft 1 revolution (360°), then align the marks as above.


OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

9.CHECK ENGINE MECHANICAL SYSTEM
5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.
A369444C01
2.427,0.854 2.74,1.052 0.313,0.198 10 false *1
*1 Oil Control Valve Filter


Remove the oil control valve filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.




OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (See page Engine / Hybrid System>2NZ-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.


k.

Read pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B

HINT:

DTC P0011 or P0012 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




A

END

B

9.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.



OK

10.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

10.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read pending DTCs.


Result
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B


A

CHECK FOR INTERMITTENT PROBLEMS

B