Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P2195).

HINT:
·

When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say the oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM uses pulse width modulation to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A327375E04
0.125,0.094 3.26,0.531 3.135,0.438 12 false Reference (System Diagram of Sensor 1): 0.104,1.063 0.583,1.469 0.479,0.406 10 false from Battery 0.792,1.313 1.479,1.531 0.688,0.219 10 false EFI MAIN 1.708,2.365 2.375,2.563 0.667,0.198 10 false EFI MAIN 0.583,3.302 1.094,3.5 0.51,0.198 10 false Ground 3.365,1.031 3.615,1.208 0.25,0.177 10 false +B 3.24,1.521 3.615,1.698 0.375,0.177 10 false A1A- 4.438,1.031 4.885,1.208 0.448,0.177 10 false HA1A 4.427,1.552 4.844,1.74 0.417,0.188 10 false A1A+ 5,1.01 5.427,1.198 0.427,0.188 10 false HA1A 4.99,1.531 5.417,1.719 0.427,0.188 10 false A1A+ 5,2.083 5.417,2.271 0.417,0.188 10 false A1A- 4.979,2.635 5.448,2.823 0.469,0.188 10 false MREL 3.771,0.802 4.26,1 0.49,0.198 10 false Heater 3.771,1.292 4.26,1.469 0.49,0.177 10 false Sensor 3.479,1.99 4.833,2.344 1.354,0.354 10 false Air Fuel Ratio Sensor 5.698,0.458 6.115,0.646 0.417,0.188 10 false ECM 6.167,1.688 6.646,2.052 0.479,0.365 10 false Duty Control



DTC No. DTC Detection Condition Trouble Area
P0031 Air fuel ratio sensor heater current less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher
(1 trip detection logic)
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

No. 1 integration relay (EFI MAIN relay)

·

ECM


P0032 Air fuel ratio sensor heater current reaches the high limit (Hybrid IC high current limiter monitor input "Fail")
(1 trip detection logic)
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

No. 1 integration relay (EFI MAIN relay)

·

ECM


P101D The heater current is higher than a specified value while the heater is not operating.
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-way Catalytic Converter (TWC) to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

CONFIRMATION DRIVING PATTERN

A198819E21
0.75,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 1.011,1.717 1.417,1.878 0.406,0.161 10 Idling 0.196,2.028 1.442,2.239 1.246,0.211 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.622 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.614,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.851,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0031, P0032 or P101D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


UNKNOWN
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [B] through [E] again.




WIRING DIAGRAM

A327376E06
5.406,0.51 5.719,0.698 0.313,0.188 10 false A83 5.448,0.333 5.667,0.5 0.219,0.167 10 false 46 5.448,0.99 5.667,1.167 0.219,0.177 10 false 23 5.385,1.365 5.688,1.542 0.302,0.177 10 false 133 5.396,1.729 5.688,1.906 0.292,0.177 10 false 134 4.063,1.063 4.208,1.219 0.146,0.156 10 false 1 4.063,1.427 4.219,1.583 0.156,0.156 10 false 3 4.063,1.802 4.208,1.958 0.146,0.156 10 false 4 3.563,1.063 4.01,1.25 0.448,0.188 10 false HA1A 0.552,0.844 0.802,1 0.25,0.156 10 false 1D 1.104,0.844 1.354,1 0.25,0.156 10 false 1D 0.823,0.854 1.031,1.021 0.208,0.167 10 false 11 1.417,0.854 1.542,1.01 0.125,0.156 10 false 7 3.177,1.073 3.448,1.26 0.271,0.188 10 false +B 2.969,1.063 3.104,1.219 0.135,0.156 10 false 2 4.063,3.344 4.208,3.5 0.146,0.156 10 false 1 4.052,3.76 4.208,3.917 0.156,0.156 10 false 3 4.063,4.271 4.208,4.427 0.146,0.156 10 false 4 2.958,3.365 3.094,3.521 0.135,0.156 10 false 2 3.573,1.396 3.979,1.583 0.406,0.188 10 false A1A+ 3.583,1.802 3.979,1.99 0.396,0.188 10 false A1A- 3.594,3.323 4,3.51 0.406,0.188 10 false HT1B 3.188,3.344 3.458,3.51 0.271,0.167 10 false +B 3.594,3.76 4.01,3.948 0.417,0.188 10 false OX1B 3.76,4.271 4.01,4.438 0.25,0.167 10 false E2 5.448,3.292 5.698,3.469 0.25,0.177 10 false 22 5.396,3.677 5.677,3.844 0.281,0.167 10 false 103 5.396,4.156 5.667,4.333 0.271,0.177 10 false 135 5.396,1.167 5.719,1.354 0.323,0.188 10 false B89 5.385,1.552 5.698,1.708 0.313,0.156 10 false B89 5.406,1.917 5.708,2.083 0.302,0.167 10 false B89 5.75,1.052 6.177,1.24 0.427,0.188 10 false HA1A 5.76,0.51 6.208,0.667 0.448,0.156 10 false MREL 5.75,1.438 6.177,1.625 0.427,0.188 10 false A1A+ 5.76,1.781 6.177,1.979 0.417,0.198 10 false A1A- 5.76,3.365 6.177,3.552 0.417,0.188 10 false HT1B 5.75,3.74 6.156,3.927 0.406,0.188 10 false OX1B 5.76,4.25 6.177,4.427 0.417,0.177 10 false EX1B 5.417,3.479 5.719,3.667 0.302,0.188 10 false B89 5.406,3.885 5.708,4.073 0.302,0.188 10 false B89 5.406,4.365 5.74,4.531 0.333,0.167 10 false B89 4.323,2.135 4.979,2.354 0.656,0.219 10 false (Shielded) 3.021,2.208 3.375,2.385 0.354,0.177 10 false B90 3.021,2.365 4.396,2.771 1.375,0.406 10 false Air Fuel Ratio Sensor 3.094,4.667 3.448,4.823 0.354,0.156 10 false F137 3.104,4.833 4.573,5.229 1.469,0.396 10 false Heated Oxygen Sensor 6.135,5.177 6.542,5.375 0.406,0.198 10 false ECM 1.958,2.521 2.208,2.677 0.25,0.156 10 false 1E 0.552,3.01 0.802,3.167 0.25,0.156 10 false 1C 1.958,2.313 2.146,2.469 0.188,0.156 10 false 10 0.865,3.01 0.99,3.167 0.125,0.156 10 false 1 0.719,2.667 1.396,2.885 0.677,0.219 10 false EFI MAIN 1.438,1.927 2.135,2.135 0.698,0.208 10 false EFI MAIN 0.719,3.26 2.167,3.479 1.448,0.219 10 false No. 1 Integration Relay 0.75,3.896 1.01,4.104 0.26,0.208 10 false R/I 0.76,4.448 1.146,4.635 0.385,0.188 10 false MAIN 0.896,4.979 1.5,5.208 0.604,0.229 10 false Battery 1.958,1.177 2.208,1.333 0.25,0.156 10 false 1E 2.01,0.969 2.135,1.125 0.125,0.156 10 false 4 0.729,1.146 1.146,1.469 0.417,0.323 10 false EFI NO. 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.
A209298C10
1.896,1.042 2.448,0.823 true 1.573,1.396 1.021,1.625 true 1.573,1.042 1.021,0.823 true 0.167,0.146 0.396,0.365 0.229,0.219 10 false *a 2.5,0.719 2.917,0.875 0.417,0.156 10 false HA1A 0.583,1.552 0.917,1.708 0.333,0.156 10 false A1A- 0.75,0.708 0.948,0.865 0.198,0.156 10 false +B
*a Component without harness connected
(Air Fuel Ratio Sensor)


Disconnect the B90 air fuel ratio sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HA1A) - 2 (+B) 20°C (68°F) 1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher



HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
U126259C02
1.865,1.083 2.427,0.865 true 0.156,0.073 0.375,0.281 0.219,0.208 10 false *a 2.49,0.74 2.75,0.948 0.26,0.208 10 false +B 0.677,1.156 0.99,1.354 0.313,0.198 10 false B90
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B90-2 (+B) - Body ground Ignition switch ON 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the B90 air fuel ratio sensor connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B90-1 (HA1A) - B89-23 (HA1A) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B90-1 (HA1A) or B89-23 (HA1A) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine and idle it for 5 minutes or more.


f.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute.


g.

Idle the engine for 5 minutes or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0031, P0032 or P101D is output B




A

B

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the B90 air fuel ratio sensor connector.


b.

Remove the No. 1 integration relay from the engine room main relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B90-2 (+B) - 1E-4 Always Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition
B90-2 (+B) or 1E-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR