Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A112653E19
0.241,2.312 0.669,2.478 0.428,0.167 10 Cover 0.952,2.387 0.655,2.387 false 1.311,2.442 2.2,2.618 0.89,0.176 10 Exhaust Gas 1.86,0.265 2.717,0.464 0.857,0.199 10 Atmosphere 3.394,0.34 3.98,0.549 0.586,0.209 10 Housing 3.444,0.665 4.683,0.836 1.239,0.171 10 Platinum Electrode 3.444,0.971 4.665,1.324 1.221,0.353 10 Solid Electrolyte (Zirconia Element) 3.444,1.864 3.951,2.04 0.507,0.176 10 Heater 3.444,2.147 4.632,2.355 1.188,0.209 10 Coating (Ceramic) 3.444,1.56 4.683,1.731 1.239,0.171 10 Platinum Electrode 4.113,0.335 5.096,0.53 0.983,0.195 10 Output Voltage 4.796,2.246 6.833,2.468 2.037,0.223 10 Richer - Air-fuel Ratio - Leaner 5.115,0.179 6.476,0.388 1.361,0.209 10 Ideal Air-fuel Mixture 3.37,0.411 3.116,0.651 false 3.426,1.036 2.881,1.036 false 3.422,0.722 2.858,0.902 false 3.425,1.63 2.902,1.484 false 3.422,1.932 2.769,1.7 false 3.43,2.213 2.873,1.901 false 2.32,2.117 1.771,2.425 false

DTC No. DTC Detection Condition Trouble Area
P0136

Abnormal voltage output:

During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage does not increase to 0.69 V or higher.

(b) Heated oxygen sensor voltage does not decrease to less than 0.21 V.



·

Heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system


P0137

Low voltage (open):

During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is less than 0.21 V.

(b) Target air-fuel ratio rich



·

Heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system


P0138

High voltage (short):

During active air-fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) Heated oxygen sensor voltage output is higher than 0.69 V.

(b) Target air-fuel ratio is lean.



·

Heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

ECM



MONITOR DESCRIPTION

Active Air-fuel Ratio Control

The ECM usually performs air-fuel ratio feedback control so that the air fuel ratio sensor output indicates a near stoichiometric air-fuel level. This vehicle includes active air-fuel ratio control in addition to regular air-fuel ratio control. The ECM performs active air-fuel ratio control to detect any deterioration in the Three-way Catalytic Converter (TWC) and heated oxygen sensor malfunctions (refer to the diagram below).

Active air-fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.


Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136)

While the ECM is performing active air-fuel ratio control, the air-fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not decrease to less than 0.21 V and does not increase to 0.69 V or higher during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136.

A392401E05
2.917,2.115 3.208,1.708 3.208,1.708 3.333,1.708 false 2.844,2.333 3.135,2.594 3.135,2.594 3.26,2.594 false 2.208,1.365 2.667,1.563 0.458,0.198 10 false Off 2.063,2.135 2.583,2.365 0.521,0.229 10 false 0.69 V 2.073,2.896 2.531,3.094 0.458,0.198 10 false 0.21 V 3.344,2.5 4.01,2.813 0.667,0.313 10 false Abnormal 3.438,1.604 3.938,1.813 0.5,0.208 10 false Normal 4.74,1.292 5.469,1.552 0.729,0.26 10 false Operation 4.51,0.781 5.813,1.063 1.302,0.281 10 false 15 to 20 seconds 0.156,2.417 1.625,3 1.469,0.583 10 false Heated Oxygen Sensor Voltage 0.135,1.344 2.646,2.26 2.51,0.917 10 false Active Air-Fuel Ratio Control 0.073,0.073 5.156,0.333 5.083,0.26 10 false Heated Oxygen Sensor Circuit Malfunction (P0136: Abnormal Voltage)


Open or Short in Heated Oxygen Sensor Circuit (DTC P0137 or P0138)

During active air-fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-way Catalytic Converter (TWC) by forcibly regulating the air-fuel ratio to become rich or lean. If the heated oxygen sensor has an open or short circuit, or the voltage output of the sensor noticeably decreases, the OSC indicated an extraordinarily high value. Even if the ECM attempts to continue regulating the air-fuel ratio to become rich or lean, the heated oxygen sensor output does not change.

While performing active air-fuel ratio control, when the target air-fuel ratio is rich and the heated oxygen sensor voltage output is less than 0.21 V (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137. When the target air-fuel ratio is lean and the voltage output is higher than 0.69 V (rich) during active air-fuel ratio control, the ECM determines that the sensor voltage output is abnormally high and stores DTC P0138.

*: The TWC has the capability to store oxygen. The OSC and the emissions purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated based on the calculated OSC value (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0420).

A395043E02
4.25,2.052 4.417,1.667 4.417,1.667 4.583,1.667 false 5.333,2.406 5.667,1.656 5.667,1.656 5.833,1.656 true 5.667,3.021 5.833,2.635 5.833,2.635 6,2.635 false 5.917,3.802 6.167,4.052 false 5.75,6.583 5.917,6.167 5.917,6.167 6.083,6.167 false 0.083,0.083 3.75,0.323 3.667,0.24 10 false Heated Oxygen Sensor Circuit Low Voltage (P0137: Open) 0.333,1.229 1.25,1.604 0.917,0.375 10 false Active Air-Fuel Ratio Control 0.333,2.104 1.75,2.563 1.417,0.458 10 false Target Air-Fuel Ratio 0.365,3.26 1.333,3.719 0.969,0.458 10 false Heated Oxygen Sensor Voltage 0.083,4.333 4.167,4.667 4.083,0.333 10 false Heated Oxygen Sensor Circuit High Voltage (P0138: Short) 2.802,1.365 3.219,1.656 0.417,0.292 10 false Off 2.125,2.073 3.021,2.469 0.896,0.396 10 false Stoichiometric Air-Fuel Level 2.5,3.208 2.948,3.417 0.448,0.208 10 false 0.69 V 2.5,3.51 2.948,3.719 0.448,0.208 10 false 0.21 V 0.417,4.917 1.333,5.292 0.917,0.375 10 false Active Air-Fuel Ratio Control 0.417,5.76 1.833,6.219 1.417,0.458 10 false Target Air-Fuel Ratio 0.417,6.635 1.385,7.094 0.969,0.458 10 false Heated Oxygen Sensor Voltage 2.5,7.031 2.948,7.24 0.448,0.208 10 false 0.21 V 2.5,6.74 2.948,6.948 0.448,0.208 10 false 0.69 V 2.052,5.708 2.948,6.104 0.896,0.396 10 false Stoichiometric Air-Fuel Level 2.74,4.969 3.156,5.26 0.417,0.292 10 false Off 4.271,0.76 5.521,1.094 1.25,0.333 10 false 15 to 20 seconds 4.49,1.281 5.74,1.615 1.25,0.333 10 false Operation 4.667,1.563 5.917,1.896 1.25,0.333 10 false Normal 5.927,1.552 6.688,1.885 0.76,0.333 10 false Abnormal 4.667,2.417 5.083,2.75 0.417,0.333 10 false Rich 6.083,2.531 6.75,2.781 0.667,0.25 10 false Normal 6.25,3.938 7.01,4.271 0.76,0.333 10 false Abnormal 4.5,4.896 5.75,5.229 1.25,0.333 10 false Operation 4.677,5.719 5.927,6.052 1.25,0.333 10 false Lean 6.188,6.063 6.948,6.396 0.76,0.333 10 false Abnormal


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Mass air flow meter
Throttle position sensor
Air fuel ratio sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated Oxygen Sensor Voltage Check (Voltage Malfunction, High Voltage and Low Voltage)
Active air-fuel ratio control Executing
Active air-fuel ratio control begins when all of the following conditions are met: -
Battery voltage 11 V or higher
Engine coolant temperature 75°C (167°F) or higher
Idling Off
Engine speed Less than 4000 rpm
Air fuel ratio sensor status Activated
Fuel system status Closed loop

TYPICAL MALFUNCTION THRESHOLDS

P0136: Heated Oxygen Sensor Voltage Check (Voltage Malfunction)
Either of the following conditions is met 1 or 2
1. Both of the following conditions are met (a) and (b)
(a) Commanded air-fuel ratio 14.3 or less
(b) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V
2. Both of the following conditions are met (c) and (d)
(c) Commanded air-fuel ratio 14.9 or more
(d) Heated oxygen sensor voltage 0.21 V or higher, and less than 0.69 V

P0137: Heated Oxygen Sensor Voltage Check (Low Voltage)
Both of the following conditions are met (a) and (b)
(a) Commanded air-fuel ratio 14.3 or less
(b) Heated oxygen sensor voltage Less than 0.21 V

P0138: Heated Oxygen Sensor Voltage Check (High Voltage)
Both of the following conditions are met (a) and (b)
(a) Commanded air-fuel ratio 14.9 or more
(b) Heated oxygen sensor voltage Higher than 0.69 V

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the heated oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A288927E09
1.333,2.854 1.5,2.854 1.5,2.854 1.729,2.438 false 0.385,0.51 1.615,0.708 1.229,0.198 10 false 100 km/h (62 mph) 0.469,1.385 1.698,1.583 1.229,0.198 10 false 85 km/h (53 mph) 1.208,2.25 2.292,2.458 1.083,0.208 10 false Idling 0.177,2.781 1.406,2.979 1.229,0.198 10 false Ignition Switch ON 2.021,2.417 3.25,2.615 1.229,0.198 10 false [A] 2.646,2.125 3.333,2.469 0.688,0.344 10 false [B] 4,0.729 4.469,1 0.469,0.271 10 false [C] 2.344,2.927 3.573,3.125 1.229,0.198 10 false Warming up 3.531,2.927 4.76,3.125 1.229,0.198 10 false 10 minutes or more 5.01,3.344 5.948,3.563 0.938,0.219 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on. [A]

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher. [B]

7.

Drive the vehicle at 85 to 100 km/h (53 to 62 mph) for 10 minutes or more. [C]

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0136, P0137 or P0138.

12.

Check the DTC judgment result.

GTS
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

GTS only:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection for A/F Sensor Volume operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2.

6.

Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air-fuel ratio)
12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air-fuel ratio)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E99
5.792,3.583 7.094,4.146 1.302,0.563 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 false 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 false 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 false -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 false 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 false -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 false -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 false -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 false 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 false 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 false 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 false 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 false 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 false -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 false -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 false -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.833,0.604 2.615,1.104 1.781,0.5 10 false Air Fuel Ratio Sensor Output Voltage 3.448,0.583 5.344,1.094 1.896,0.51 10 false Heated Oxygen Sensor Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.469 7.156,5.073 1.354,0.604 10 false - Air fuel ratio sensor circuit 5.917,5.688 7,6.115 1.083,0.427 10 false - Heated oxygen sensor 5.927,6.146 7,6.688 1.073,0.542 10 false - Heated oxygen sensor heater 5.927,6.781 7.042,7.354 1.115,0.573 10 false - Heated oxygen sensor circuit 5.927,7.698 6.813,8.104 0.885,0.406 10 false - Fuel injector assembly 5.917,8.115 7.073,8.448 1.156,0.333 10 false - Fuel pressure 5.917,8.365 6.969,9.375 1.052,1.01 10 false - Gas leak from exhaust system (air-fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2; then press the view button.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0136, P0137 (DTC P0136, P0137 OR P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
DTC P0136, P0137 or P0138 and other DTCs are output D

HINT:

If any DTCs other than P0136, P0137 and P0138 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (O2S B1S2)

B

12.CHECK FOR EXHAUST GAS LEAK

C

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

D

2.READ VALUE USING GTS (O2S B1S2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2.


f.

Allow the engine to idle.


g.

Read the heated oxygen sensor output voltage while idling.

Result
Heated Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B



A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.
A326245C04
1.479,1.156 1.063,0.76 true 2.354,1.833 1.938,1.438 true 1.458,1.458 1.021,1.729 true 2.438,1.76 2.865,1.948 0.427,0.188 10 false OX1B 0.833,0.563 1.083,0.76 0.25,0.198 10 false +B 0.104,0.094 0.333,0.333 0.229,0.24 10 false *a 0.771,1.646 1.083,1.844 0.313,0.198 10 false E2
*a Component without harness connected
(Heated Oxygen Sensor)


Disconnect the F137 heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+B) - 3 (OX1B) Always 10 kΩ or higher
2 (+B) - 4 (E2) Always 10 kΩ or higher



HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the ignition switch off and wait for 5 minutes or more.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-22 (HT1B) - B89-103 (OX1B) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the GTS, and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the GTS.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air-fuel ratio) Alternates between higher than and less than 3.3 V OK
AFS Voltage B1S1 (Air-fuel ratio) Remains at higher than 3.3 V NG
AFS Voltage B1S1 (Air-fuel ratio) Remains at less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A285391E18
3.083,2.938 3.583,2.469 false 2.25,1.094 2.667,1.594 false 4.854,0.167 5,0.167 5,0.167 5.083,0.448 false 5.333,2.219 5.927,1.26 5.927,1.26 5.521,2.417 true 5.646,2.667 5.167,2.417 false 3.833,1.688 3.667,1.615 false 5.917,1.26 5.333,1.594 false 2.146,0.25 2.646,0.5 0.5,0.25 10 false 12.5% 5.979,1.156 6.896,2.156 0.917,1 10 false Air Fuel Ratio Sensor Output 3.542,1.031 4.042,1.26 0.5,0.229 10 false -12.5% 1.521,0.958 2.271,1.208 0.75,0.25 10 false Malfunction 3.635,2.385 4.615,2.823 0.979,0.438 10 false Heated Oxygen Sensor Output 3.875,1.625 4.375,1.875 0.5,0.25 10 false Normal 1,1.844 1.417,2.094 0.417,0.25 10 false 3.3 V 1.135,2.823 1.469,3.073 0.333,0.25 10 false 1 V 1.125,3.354 1.458,3.604 0.333,0.25 10 false 0 V 5.698,2.594 6.635,2.792 0.938,0.198 10 false Malfunctioning 3.813,0.083 4.938,0.365 1.125,0.281 10 false Injection Volume



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

9.REPLACE AIR FUEL RATIO SENSOR
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 2.2 mA in this test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



g.

Stop the vehicle.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1S1.


i.

Drive the vehicle up to 60 km/h (37 mph) or more and then decelerate for 5 seconds or more. Perform this at least 3 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A152792E72
1.354,2.51 2.635,2.698 1.281,0.188 10 false 10 minutes or more 2.969,2.51 4.177,2.698 1.208,0.188 10 false 5 seconds or more 4.271,2.51 5.469,2.698 1.198,0.188 10 false 5 seconds or more 5.563,2.51 6.74,2.698 1.177,0.188 10 false 5 seconds or more 0.156,0.073 1.458,0.292 1.302,0.219 12 false Driving Pattern: 0.448,1.427 1.031,1.792 0.583,0.365 10 false 60 km/h (37 mph) 0.521,2.208 1.021,2.594 0.5,0.385 10 false 0 km/h (0 mph)


j.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard Current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS.





OK

15.REPLACE HEATED OXYGEN SENSOR

NG

9.REPLACE AIR FUEL RATIO SENSOR
7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S2.


f.

Change the fuel injection volume using the GTS and monitor the voltage output of the heated oxygen sensors displayed on the GTS.

NOTICE:

The heated oxygen sensor has a maximum output delay of approximately 20 seconds.


HINT:

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.


Standard Voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.




OK

8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

12.CHECK FOR EXHAUST GAS LEAK
8.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the GTS and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the GTS.

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the GTS.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result
GTS Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air-fuel ratio) Alternates between higher than and less than 3.3 V OK
AFS Voltage B1S1 (Air-fuel ratio) Remains at higher than 3.3 V NG
AFS Voltage B1S1 (Air-fuel ratio) Remains at less than 3.3 V NG

HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1) remains at either less or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A285391E16
3.083,2.938 3.583,2.469 false 2.25,1.094 2.667,1.594 false 4.854,0.167 5,0.167 5,0.167 5.083,0.448 false 5.333,2.219 5.927,1.26 5.927,1.26 5.521,2.417 true 5.646,2.667 5.167,2.417 false 3.833,1.688 3.667,1.615 false 5.917,1.26 5.333,1.594 false 2.146,0.25 2.646,0.5 0.5,0.25 10 false 12.5% 5.979,1.156 6.896,1.563 0.917,0.406 10 false Air Fuel Ratio Sensor Output 3.542,1.031 4.042,1.26 0.5,0.229 10 false -12.5% 1.521,0.958 2.271,1.208 0.75,0.25 10 false Malfunction 3.635,2.385 4.615,2.823 0.979,0.438 10 false Heated Oxygen Sensor Output 3.875,1.625 4.375,1.875 0.5,0.25 10 false Normal 1,1.844 1.417,2.094 0.417,0.25 10 false 3.3 V 1.135,2.823 1.469,3.073 0.333,0.25 10 false 1 V 1.125,3.354 1.458,3.604 0.333,0.25 10 false 0 V 5.698,2.594 6.635,2.792 0.938,0.198 10 false Malfunctioning 3.813,0.083 4.938,0.365 1.125,0.281 10 false Injection Volume



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

9.REPLACE AIR FUEL RATIO SENSOR
9.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION)




NEXT

10.PERFORM CONFIRMATION DRIVING PATTERN
10.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the confirmation driving pattern.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136, P0137 or P0138.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.


Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137 or P0138 is output)
A
NORMAL
(DTC is not output)
B


A

B

END

12.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leakage.

OK:

No gas leakage.


HINT:

Perform "Inspection After Repair" after replacing the exhaust system (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

13.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

13.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

14.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

14.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the F137 heated oxygen sensor connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F137-1 (HT1B) - B89-22 (HT1B) Always Below 1 Ω
F137-3 (OX1B) - B89-103 (OX1B) Always Below 1 Ω
F137-4 (E2) - B89-135 (EX1B) Always Below 1 Ω
F137-1 (HT1B) or B89-22 (HT1B) - Body ground Always 10 kΩ or higher
F137-3 (OX1B) or B89-103 (OX1B) - Body ground Always 10 kΩ or higher




OK

15.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform the confirmation driving pattern.



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


e.

Input the DTC: P0136, P0137 or P0138.


f.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.


Result
Result Proceed to
ABNORMAL
(DTC P0136, P0137 or P0138 is output)
A
NORMAL
(DTC is not output)
B


A

B

END