Use the following procedure to troubleshoot the pre-crash safety system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
| Pre-crash Safety System Customer Problem Analysis | Vehicle Brought to Workshop | ||||||
| Year | Month | Day | |||||
| Dealer name | Person in charge at headquarters | Telephone number | |||||
| Shop name | Person in charge at shop | ||||||
| Frame type | Frame No. | First Registered Year | Total distance traveled | ||||
| Customer Concerns
(Include details) |
Does not operate | ||||||
| Operates abnormally | |||||||
| Date of malfunction occurrence
(Since when) |
Year | Month | Day | Approx. Time | |||
| Date of last inspection | Year | Month | Day | ||||
| Frequency of problem symptoms | Once / Occasionally (times per day, times per month) / Every time certain conditions are met ( ) | ||||||
| Weather | Sunny / Cloudy / Rain (Heavy/Light) / Snow (Amount of snowfall cm) / Other ( ) | Vehicle speed | Approximately ( ) km/h (mph) | ||||
| Place | Prefecture
(Attach a map if possible) |
||||||
| Driving path (where vehicle turned, where driver attempted to drive to, etc.)
* Describe the conditions immediately after the occurrence in as much detail as possible. |
Conditions of Occurrence Diagram | ||||||
0.781,1.458 0.688,0.583
0.688,0.583 0.844,0.583
true
1.385,1.396 1.76,0.854
1.76,0.854 1.917,0.854
true
1.885,1.427 2.448,1.521
2.448,1.521 2.448,1.708
true
1.604,1.781 1.969,2.469
1.969,2.469 2.125,2.469
true
1.438,2.177 1.729,2.927
1.729,2.927 1.885,2.927
true
0.698,2.833 1.125,1.906
true
0.688,0.073 1.865,0.271
1.177,0.198
10
false
Diagram Example
0.896,0.5 2.021,0.677
1.125,0.177
10
false
Oncoming vehicle
1.031,0.823 1.427,0.99
0.396,0.167
10
false
North
1.969,0.771 2.979,0.979
1.01,0.208
10
false
Stopped vehicle
2.104,1.698 3.083,2.052
0.979,0.354
10
false
Approximately ( ) m
0.313,2.844 1.25,3.021
0.938,0.177
10
false
Occurred here
2.177,2.385 2.698,2.583
0.521,0.198
10
false
Vehicle
1.927,2.844 2.542,3.042
0.615,0.198
10
false
Guardrail
|
|||||||
| Surrounding road conditions
Describe whether there were any billboards, metal objects on the road (manholes), guardrails, pipes, cat's eyes, gate bars, etc. |
|||||||
| Urban area / Suburbs / Highway / Other ( ) | Road surface conditions | Temperature | About °C ( °F) | ||||
| Direction of travel | Straight / Right turn / Left turn / Right curve / Left curve | Snow wall(s) | Y / N | ||||
| Driving lane | Number of lanes on one side (lanes) / ( ) lane(s) from left | Backlighting | Y / N | ||||
| Condition of external area around detection sensor | No foreign matter adhesion / Foreign matter adhesion (water, snow, ice, other) | ||||||
| Additional information about condition of vehicle exterior
(other than above) |
|||||||
| DTC | First Time (when vehicle brought to workshop) | ||||||
| Second Time (after clearing DTC) | |||||||
| Status of operation switch | Pre-crash safety system cancel switch | Far / Medium / Near / OFF | VSC OFF switch | ON / OFF | |||
| Serial number of main part
* Fill in when removing, installing or replacing part |
Pre-crash safety city sensor | ||||||
| Describe the items to the right in as much detail as possible. | Driver operation | Accelerator pedal operated / Brake pedal operated / Steering wheel operated | Time elapsed after engine is started | Approximately ( ) minutes | |||
| Tire pressure inspection result | Front: LH ( ) kPa RH ( ) kPa Standard ( ) kPa | ||||||
| Rear: LH ( ) kPa RH ( ) kPa Standard ( ) kPa | |||||||
| Sensor optical axis inspection result | Pre-crash safety city sensor | Vertical ( ) | Horizontal ( ) | ||||
| History of repairs around radar sensor | Y / N | Accident history | Y / N | ||||
| Vehicle modified | Y ( ) / N | ||||||
| Items installed or attached around windshield glass | Drive recorder* / Radar detector / Navigation unit (genuine/non-genuine) / ETC / Charms or toys / Other:
*: Since this device holds information valuable to the investigation, make sure to retrieve this device if permission is granted by the customer. |
||||||
| Proceed to |
|---|
| NEXT |
NEXT
Check if any warning lights other than the PCS warning light (PCS OFF indicator) are illuminated or blinking.
| Result | Proceed to |
|---|---|
| Only the PCS warning light (PCS OFF indicator) is blinking | A |
| The PCS warning light (PCS OFF indicator) and other warning lights are illuminated or blinking | B |
A
B
Clear the DTCs.
(See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR)
Check for DTCs.
(See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR)
| Result | Proceed to |
|---|---|
| DTCs are not output (symptoms can be confirmed or reproduced) | A |
| DTCs are not output (symptoms cannot be confirmed or reproduced) | B |
| DTCs are output | C |
A
B
C
Read the Data List according to the display on the GTS.
(See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST)
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| History of Blockage | Displays whether there is camera or laser sensor obstruction history / ON or OFF | ON: Pre-crash safety city sensor (camera or laser sensor) obstruction history exists
OFF: Pre-crash safety city sensor (camera or laser sensor) obstruction history does not exist |
- |
| History of Low Voltage | Displays whether there is low voltage history / ON or OFF | ON: Pre-crash safety city sensor low voltage history exists
OFF: Pre-crash safety city sensor low voltage history does not exist |
- |
| History of High Voltage | Displays whether there is high voltage history / ON or OFF | ON: Pre-crash safety city sensor high voltage history exists
OFF: Pre-crash safety city sensor high voltage history does not exist |
- |
| History of Low
Temperature |
Displays whether there is low temperature history /ON or OFF | ON: Pre-crash safety city sensor low temperature history exists
OFF: Pre-crash safety city sensor low temperature history does not exist |
- |
| History of High
Temperature |
Displays whether there is high temperature history / ON or OFF | ON: Pre-crash safety city sensor high temperature history exists
OFF: Pre-crash safety city sensor high temperature history does not exist |
- |
| Blockage Status | Displays whether there is a camera obstruction malfunction / ON or OFF | ON: Pre-crash safety city sensor (camera) obstructed
OFF: Pre-crash safety city sensor (camera) not obstructed |
- |
| Low Voltage Status | Displays whether there is a low voltage malfunction / ON or OFF | ON: Pre-crash safety city sensor low voltage malfunction exists
OFF: Pre-crash safety city sensor low voltage malfunction does not exist |
- |
| High Voltage Status | Displays whether there is a high voltage malfunction / ON or OFF | ON: Pre-crash safety city sensor high voltage malfunction exists
OFF: Pre-crash safety city sensor high voltage malfunction does not exist |
- |
| Low Temperature Status | Displays whether there is a low temperature malfunction / ON or OFF | ON: Pre-crash safety city sensor low temperature malfunction exists
OFF: Pre-crash safety city sensor low temperature malfunction does not exist |
- |
| High Temperature Status | Displays whether there is a high temperature malfunction / ON or OFF | ON: Pre-crash safety city sensor high temperature malfunction exists
OFF: Pre-crash safety city sensor high temperature malfunction does not exist |
- |
| Lidar Blockage Status | Displays whether laser sensor is dirty / ON or OFF | ON: Dirt on Pre-crash safety city sensor (laser sensor)
OFF: No dirt on Pre-crash safety city sensor (laser sensor) |
- |
| DTC Condition | Proceed to |
|---|---|
| Malfunction history exists | A |
| No malfunction history exists | B |
A
B
Refer to Problem Symptoms Table.
(See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>PROBLEM SYMPTOMS TABLE)
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Terminals of ECU
(See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>TERMINALS OF ECU)
Data List / Active Test
(See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST)
| Proceed to |
|---|
| NEXT |
NEXT
Adjustment of the pre-crash safety city sensor is required when the pre-crash safety city sensor is replaced with a new one.
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT