The pre-crash safety city sensor receives G sensor signals from the airbag ECU assembly (yaw rate sensor) and outputs this DTC when a G sensor malfunction is received.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1A48 | All of the following conditions are met: -
5 seconds have elapsed since the ignition switch to ON. -
The battery voltage is 10 V or more for 3 seconds or more. -
The pre-crash safety city sensor receives a G sensor malfunction signal from the airbag ECU assembly (yaw rate sensor) for 1 second or more. |
·
Vehicle stability control system ·
Airbag ECU assembly (yaw rate sensor) ·
Pre-crash safety city sensor |
When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.
If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed to troubleshooting (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1A48 is not output | A |
| DTC C1A48 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Replace the pre-crash safety city sensor (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>REMOVAL).
Perform pre-crash safety city sensor learning.
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
NEXT
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1A48 is not output | A |
| DTC C1A48 is output | B |
A
B