Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.01
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

The brake actuator assembly (skid control ECU) outputs a stop light signal to the stop light switch assembly. When the brake actuator assembly (skid control ECU) detects a malfunction relating to the stop light circuit, the pre-crash safety city sensor is notified via CAN communication, and C1A4B is output.

DTC Code DTC Detection Condition Trouble Area
C1A4B

All of the following conditions are met:

-

3 seconds have elapsed since the ignition switch to ON.

-

The battery voltage is 10 V or more for 3 seconds or more.

-

Communication between the pre-crash safety city sensor and brake actuator assembly (skid control ECU) is normal.

-

The pre-crash safety city sensor receives a stop light relay circuit malfunction signal from the brake actuator assembly (skid control ECU) for 1 second or more.



·

Lighting system

·

Harness or connector

·

Stop light switch assembly

·

Brake actuator assembly (Skid control ECU)



WIRING DIAGRAM

C335074N06
1.865,0.271 3.094,0.469 1.229,0.198 10 false from Battery 0.833,0.417 2.063,0.615 1.229,0.198 10 false STOP 2,1.156 2.156,1.354 0.156,0.198 10 false 7 2,2.552 2.156,2.75 0.156,0.198 10 false 2 3.594,2.552 3.75,2.75 0.156,0.198 10 false 1 3.594,1.729 3.75,1.927 0.156,0.198 10 false 4 3.594,0.917 3.75,1.115 0.156,0.198 10 false 3 4.969,0.917 5.198,1.104 0.229,0.188 10 false 22 5.031,2.552 5.271,2.76 0.24,0.208 10 false 2 3.229,1.729 3.688,1.927 0.458,0.198 10 false ACC 3.24,2.552 3.698,2.75 0.458,0.198 10 false OUT 3.385,0.917 3.844,1.115 0.458,0.198 10 false L 2.188,1.156 2.646,1.354 0.458,0.198 10 false B 2.208,2.552 2.667,2.75 0.458,0.198 10 false GND 5.25,0.917 5.865,1.115 0.615,0.198 10 false STP2 5.25,1.729 5.865,1.927 0.615,0.198 10 false STPO 5.26,2.552 5.875,2.75 0.615,0.198 10 false STP 2.01,2.938 2.323,3.135 0.313,0.198 10 false A92 2,3.083 4.292,3.281 2.292,0.198 10 false Stop Light Switch Assembly 2.958,3.677 3.917,3.979 0.958,0.302 10 false to Stop Light 0.188,5.719 2.198,5.938 2.01,0.219 10 false Pre-crash Safety City Sensor 5.292,5.719 5.604,5.917 0.313,0.198 10 false A54 5.281,5.865 6.865,6.26 1.583,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 1.198,6.323 3.229,6.542 2.031,0.219 10 false : CAN Communication Line 4.969,1.729 5.208,1.938 0.24,0.208 10 false 31

CAUTION / NOTICE / HINT

NOTICE:
·

When this DTC is output, a malfunction in the lighting system is suspected. Check if the lighting system is functioning normally (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the pre-crash safety city sensor, replace it with a new one and be sure to initialize the settings. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

·

Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed to troubleshooting (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:

The stop lights illuminate when the brake pedal is depressed. The stop lights turn off when the brake pedal is released.




OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY POWER SOURCE TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY POWER SOURCE TERMINAL)
a.

Turn the ignition switch to off.


b.
B331566E04
0.25,1 0.75,1.25 0.5,0.25 1.385,1.344 1.167,1.833 true 2.469,1.323 2.75,1.833 true 0.208,0.104 0.5,0.302 0.292,0.198 10 false *a 0.385,1.031 0.677,1.229 0.292,0.198 10 false A92 2.76,1.854 3.052,2.052 0.292,0.198 10 false B 0.969,1.854 1.385,2.052 0.417,0.198 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A92-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A92-2 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector (to Skid Control Buzzer)


OK

3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C360141E03
1.479,0.167 1.979,0.417 0.5,0.25 2.5,0.417 2.094,1.323 true 1.615,0.208 2.073,0.406 0.458,0.198 10 false A54 2.552,0.271 3.01,0.469 0.458,0.198 10 false STP2 0.25,0.167 0.5,0.406 0.25,0.24 10 false *a

Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-22 (STP2) - Body ground Brake pedal depressed 11 to 14 V
A54-22 (STP2) - Body ground Brake pedal released Below 1.5 V



Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


OK

4.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)
4.PERFORM ACTIVE TEST USING GTS (STOP LAMP RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


b.

Perform "Active Test" according to the display on the GTS.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Switches stop light ON/OFF Possible at vehicle speed of 0 km/h (0 mph)


c.

Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.


d.

Check the Data List for proper functioning of the stop light control relay (STOP LAMP relay).

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light switch assembly output / ON or OFF ON: Stop light switch assembly output on (Stop light on)
OFF: Stop light switch assembly output off (Stop light off)
-

Result
Result Proceed to
Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off. A
Data List content and stop light operation are normal. B



A

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A54 brake actuator assembly (skid control ECU) connector.


b.

Disconnect the A92 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-31 (STPO) - A92-4 (ACC) Always Below 1 Ω
A54-31 (STPO) or A92-4 (ACC) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A54 brake actuator assembly (skid control ECU) connector.


b.

Disconnect the A92 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-2 (STP) - A92-1 (OUT) Always Below 1 Ω




OK

7.CHECK HARNESS OR CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS OR CONNECTOR (STP TERMINAL)
a.
C360141E02
1.479,0.167 1.979,0.417 0.5,0.25 0.667,0.5 1.25,1.083 true 1.615,0.208 2.073,0.406 0.458,0.198 10 false A54 0.344,0.417 0.802,0.615 0.458,0.198 10 false STP

Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-2 (STP) - Body ground Brake pedal depressed 11 to 14 V
A54-2 (STP) - Body ground Brake pedal released Below 1.5 V



Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


OK

8.CHECK FOR DTCs

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

8.CHECK FOR DTCs

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A4B is not output A
DTC C1A4B is output B



A

B

REPLACE PRE-CRASH SAFETY CITY SENSOR

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A54 brake actuator assembly (skid control ECU) connector.


b.

Disconnect the A92 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-22 (STP2) - A92-3(L) Always Below 1 Ω
A54-22 (STP2) or A92-3(L) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR