Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.01
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1AA4  Yaw Rate Sensor Circuit  C1AA5  Yaw Rate Sensor Power Supply Voltage Circuit  


DESCRIPTION

The pre-crash safety city sensor receives vehicle stability signals from the airbag ECU assembly (yaw rate sensor). When the pre-crash safety city sensor detects a malfunction in the airbag ECU assembly (yaw rate sensor), a DTC is output.

DTC Code DTC Detection Condition Trouble Area
C1AA4 Both of the following conditions are met:
1.

All of the following conditions are met:

-

3 seconds have elapsed since the ignition switch to ON.

-

The battery voltage is 10 V or more for 3 seconds or more.


2.

All of the following conditions are met for 1 second or more:

-

The vehicle is being driven at 5 km/h (4 mph) or more.

-

Communication between the pre-crash safety city sensor and airbag ECU assembly (yaw rate sensor) is normal.

-

The pre-crash safety city sensor receives an airbag ECU assembly (yaw rate sensor) malfunction signal from the airbag ECU assembly (yaw rate sensor).



·

Vehicle stability control system

·

Pre-crash safety city sensor

·

Airbag ECU assembly (yaw rate sensor)


C1AA5 Both of the following conditions are met:
1.

All of the following conditions are met:

-

3 seconds have elapsed since the ignition switch to ON.

-

The battery voltage is 10 V or more for 3 seconds or more.


2.

All of the following conditions are met for 1 second or more:

-

The vehicle is being driven at 5 km/h (4 mph) or more.

-

Communication between the pre-crash safety city sensor and airbag ECU assembly (yaw rate sensor) is normal.

-

The pre-crash safety city sensor receives an airbag ECU assembly (yaw rate sensor) power source malfunction signal from the airbag ECU assembly (yaw rate sensor).



·

Vehicle stability control system

·

Pre-crash safety city sensor

·

Airbag ECU assembly (yaw rate sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

·

Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed to troubleshooting (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.


e.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
Vehicle stability control system DTCs are not output A
Vehicle stability control system DTCs are output B



A

2.CHECK FOR DTCs

B

2.CHECK FOR DTCs

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

B

3.REPLACE PRE-CRASH SAFETY CITY SENSOR
3.REPLACE PRE-CRASH SAFETY CITY SENSOR
a.

Replace the pre-crash safety city sensor (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>REMOVAL).


b.

Perform pre-crash safety city sensor learning.

·

Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".




NEXT

4.CHECK FOR DTCs
4.CHECK FOR DTCs

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1AA4 and C1AA5 are not output A
DTC C1AA4 or C1AA5 is output B



A

END (PRE-CRASH SAFETY CITY SENSOR WAS DEFECTIVE)

B

REPLACE AIRBAG ECU ASSEMBLY (YAW RATE SENSOR)