Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.01–2018.06
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1AA7  Skid Control Buzzer Circuit  


DESCRIPTION

When the pre-crash safety city sensor uses pre-crash safety control to sound a warning, a buzzer signal is output to the pre-crash safety city buzzer. This DTC is output when the pre-crash safety city sensor detects a malfunction in the pre-crash safety city buzzer circuit.

DTC Code DTC Detection Condition Trouble Area
C1AA7

The battery voltage is 9 V or more and either of the following conditions is met:

-

Voltage at the BUZ terminal of the pre-crash safety city sensor is 0.703 V or more for 0.06 seconds or more when a pre-crash safety city buzzer request signal is being output.

-

Voltage at the BUZ terminal of the pre-crash safety city sensor is 0.134 V or less for 0.06 seconds or more when a pre-crash safety city buzzer request signal is not being output.



·

Pre-crash safety city buzzer

·

Pre-crash safety city sensor

·

Harness or connector



WIRING DIAGRAM

B459683E01
0.094,0.656 1.51,0.854 1.417,0.198 10 false from IG1 NO. 1 Relay 2.26,0.833 2.844,1 0.583,0.167 10 false GAUGE 3.385,0.594 3.635,0.76 0.25,0.167 10 false 2 4.51,0.604 4.76,0.771 0.25,0.167 10 false 1 3.604,0.698 3.938,0.865 0.333,0.167 10 false IG1 4.198,0.698 4.531,0.865 0.333,0.167 10 false BZ 3.115,1 3.531,1.167 0.417,0.167 10 false F138 3.115,1.146 5.031,1.396 1.917,0.25 10 false Pre-crash Safety City Buzzer 5.344,0.604 5.594,0.771 0.25,0.167 10 false 8 5.583,0.698 5.917,0.865 0.333,0.167 10 false BUZ 5.167,2.042 5.5,2.208 0.333,0.167 10 false L11 5.156,2.198 7.073,2.448 1.917,0.25 10 false Pre-crash Safety City Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

·

Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".



PROCEDURE

1.INSPECT PRE-CRASH SAFETY CITY BUZZER
a.

Remove the pre-crash safety city buzzer (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL).


b.


OK

2.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - BATTERY)

NG

2.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - BATTERY)
a.
B338290E31
0.5,1.25 1,1.5 0.5,0.25 2,1.583 2.417,1.833 true 0.583,1.281 1.198,1.479 0.615,0.198 10 false F138 2.448,1.865 3.063,2.063 0.615,0.198 10 false IG1 0.135,0.115 0.75,0.313 0.615,0.198 10 false *a

Disconnect the pre-crash safety city buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F138-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
F138-2 (IG1) - Body ground Ignition switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Pre-crash Safety City Buzzer)


OK

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - PRE-CRASH SAFETY CITY SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - PRE-CRASH SAFETY CITY SENSOR)
a.

Disconnect the F138 pre-crash safety city buzzer connector.


b.

Disconnect the L11 pre-crash safety city sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F138-1 (BZ) - L11-8 (BUZ) Always Below 1 Ω
F138-1 (BZ) - Body ground Always 10 kΩ or higher




OK

REPLACE PRE-CRASH SAFETY CITY SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR