The pre-crash safety city sensor receives steering angle information from the spiral cable with sensor sub-assembly (steering angle sensor). If the pre-crash safety city sensor detects a steering angle sensor malfunction, DTC C1A47 is stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1A47 | Both of the following conditions are met:
1.
All of the following conditions are met: -
3 seconds have elapsed since the ignition switch was turned ON. -
The battery voltage is 10 V or more for 3 seconds or more. 2.
All of the following conditions are met for 1 second or more: -
The vehicle is being driven at 50 km/h (32 mph) or more. -
Communication between the pre-crash safety city sensor and spiral cable with sensor sub-assembly (steering sensor) is normal. -
The pre-crash safety city sensor receives a spiral cable with sensor sub-assembly (steering sensor) malfunction signal from the spiral cable with sensor sub-assembly (steering sensor). |
·
Vehicle Stability Control System ·
Spiral cable with sensor sub-assembly (steering angle sensor) ·
Pre-crash safety city sensor |
When replacing the pre-crash safety city sensor, replace it with a new one and be sure to initialize the settings. If a pre-crash safety city sensor which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be stored.
If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Pre-crash Safety City Sensor Learning.
Adjustment (One time recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Adjustment (Sequential recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed to troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
| Result | Proceed to |
|---|---|
| Vehicle Stability Control System DTCs are not output | A |
| Vehicle Stability Control System DTCs are output | B |
A
B
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1A47 is not output | A |
| DTC C1A47 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Replace the pre-crash safety city sensor with a new or normally functioning one.
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>REMOVAL
Perform pre-crash safety city sensor beam axis learning.
Adjustment (One time recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Adjustment (Sequential recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
NEXT
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1A47 is not output | A |
| DTC C1A47 is output | B |
A
B