Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU connector is disconnected from the brake actuator assembly.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.


WIRING DIAGRAM

C243295E09
2.854,0.625 3.813,0.771 0.958,0.146 10 false ECU-IG NO. 2 4.792,0.333 4.969,0.469 0.177,0.135 10 false 34 4.833,1.385 5.01,1.521 0.177,0.135 10 false 1 4.719,2.51 4.99,2.656 0.271,0.146 10 false A70 5.115,0.458 5.354,0.594 0.24,0.135 10 false IG1 5.125,1.5 5.552,1.667 0.427,0.167 10 false GND1 4.802,2.729 6.313,3.042 1.51,0.313 10 false Skid Control ECU (Brake Actuator Assembly) 2.625,1.542 2.802,1.698 0.177,0.156 10 false IG 2.375,2.063 2.771,2.229 0.396,0.167 10 false Brake 2.271,2.583 2.583,2.729 0.313,0.146 10 false CPU 1.5,3.552 1.771,3.708 0.271,0.156 10 false SW 1.24,3.427 1.427,3.573 0.188,0.146 10 false 12 2.156,3.948 2.677,4.094 0.521,0.146 10 false CAN I/F 1.323,4.531 1.698,4.677 0.375,0.146 10 false D100 1.719,4.531 3.573,4.698 1.854,0.167 10 false Combination Meter Assembly 0.292,4.198 0.396,4.354 0.104,0.156 10 false 1 0.656,4.708 0.927,4.854 0.271,0.146 10 false A62 0.667,4.875 2.406,5.365 1.74,0.49 10 false Brake Master Cylinder Reservoir Assembly (Brake Fluid Level Warning Switch) 0.469,4.385 0.573,4.531 0.104,0.146 10 false + 0.448,5.125 0.573,5.271 0.125,0.146 10 false E 0.302,5.302 0.406,5.448 0.104,0.146 10 false 2 4.125,5.052 4.219,5.208 0.094,0.156 10 false 1 2.896,5.229 3.26,5.375 0.365,0.146 10 false D116 2.896,5.365 4.906,5.51 2.01,0.146 10 false Parking Brake Switch Assembly 5.104,4.073 6.125,4.24 1.021,0.167 10 false Main Body ECU 5.125,5.167 5.313,5.313 0.188,0.146 10 false 3A 5.146,4.979 5.323,5.135 0.177,0.156 10 false 28 5.74,4.969 5.917,5.125 0.177,0.156 10 false 12 4.969,5.531 6.604,5.844 1.635,0.313 10 false Instrument Panel Junction Block Assembly 0.74,6.354 2.479,6.521 1.74,0.167 10 false : CAN Communication Line 5.594,4.75 5.896,4.906 0.302,0.156 10 false PKB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU(brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

B

C

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
U158340E01
1.625,0.133 1.920,0.314 0.295,0.181 10 A55 0.125,0.109 0.316,0.272 0.191,0.163 10 *a 2.074,1.924 2.326,2.062 0.252,0.137 10 IG1 2.297,1.324 2.197,1.907 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A55-34 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


d.

Turn the ignition switch off.



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U158341E01
1.625,0.133 1.920,0.314 0.295,0.181 10 A55 0.125,0.109 0.316,0.272 0.191,0.163 10 *a 0.018,0.935 0.437,1.072 0.419,0.137 10 GND1 1.151,0.998 0.535,1.037 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
A55-1 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


b.

Reconnect the skid control ECU (brake actuator assembly) connector.



OK

6.READ VALUE USING GTS (PARKING BRAKE SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.READ VALUE USING GTS (PARKING BRAKE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch / OFF or ON OFF: Parking brake released
ON: Parking brake applied
-


f.

Using the GTS, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

NG

12.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
a.
C235854E01
0.175,0.239 0.361,0.400 0.186,0.161 10 *a

Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A25 brake fluid level warning switch connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch)

e.

Reconnect the A25 brake fluid level warning switch connector.


f.

Reinstall the reservoir filler cap and strainer.


Result
Result
OK
NG


OK

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the A25 brake fluid level warning switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-12 (SW) - A25-1 (+) Always Below 1 Ω
A25-2 (E) - Body ground Always Below 1 Ω
F1-12 (SW) - Body ground Always 10 kΩ or higher



d.

Reconnect the F1 combination meter assembly connector.


e.

Reconnect the A25 brake fluid level warning switch connector.



OK

9.READ VALUE USING GTS (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light / OFF or ON OFF -


g.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF B
OFF Changes between ON and OFF A
Does not change between ON and OFF B

h.

Disconnect the GTS from the DLC3.



A

10.REPLACE COMBINATION METER ASSEMBLY

B

10.REPLACE COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the combination meter assembly (See pageVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

11.INSPECT COMBINATION METER ASSEMBLY
11.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Perform Active Test of the combination meter assembly using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The brake warning light turns ON or OFF in accordance with the GTS.


Result
Proceed to
OK
NG



OK

END

NG

12.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL).


b.

Inspect the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION).



OK

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Disconnect the F22 parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 (PKB) - F22-1 Always Below 1 Ω
3A-28 (PKB) - Body ground Always 10 kΩ or higher



d.

Reconnect the 3A instrument panel junction block assembly connector.


e.

Reconnect the F22 parking brake switch assembly connector.



OK

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See pagePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 -12 (PKB) Always Below 1 Ω
3A-28 - Body ground Always 10 kΩ or higher



c.

Reconnect the instrument panel junction block assembly connector.


d.

Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY