Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C243294E06
0.875,1.177 1.219,1.313 0.344,0.135 10 false CPU 1.74,0.667 2.271,0.802 0.531,0.135 10 false CAN I/F 1.042,1.854 1.365,1.99 0.323,0.135 10 false ABS 1.771,2.427 1.948,2.583 0.177,0.156 10 false IG 0.573,2.75 2.417,2.917 1.844,0.167 10 false Combination Meter Assembly 3.875,2.448 4.813,2.604 0.938,0.156 10 false ECU-IG NO. 2 5.667,1.417 5.771,1.573 0.104,0.156 10 false 1 5.844,1.521 6.26,1.677 0.417,0.156 10 false GND1 5.583,2.208 5.781,2.365 0.198,0.156 10 false 34 5.854,2.323 6.104,2.479 0.25,0.156 10 false IG1 5.458,2.75 7,3.125 1.542,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.469,2.563 5.74,2.708 0.271,0.146 10 false A54 1.167,3.354 2.896,3.5 1.729,0.146 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result
Result Proceed to
DTC is not output A
DTC is output (w/o Toyota Safety Sense) B
DTC is output (w/ Toyota Safety Sense) C


A

3.INSPECT BATTERY

B

C

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

B

C

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light/OFF or ON OFF: Warning light off
ON: Warning light on
-


f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light OFF/ON Observe combination meter
[Vehicle condition]
Vehicle stopped

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF B
OFF Changes between ON and OFF A
Does not change between ON and OFF B


A

7.REPLACE COMBINATION METER ASSEMBLY

B

7.REPLACE COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

8.CHECK COMBINATION METER ASSEMBLY
8.CHECK COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Perform Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The ABS warning light turns on or off in accordance with the GTS.




OK

END

NG