Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › from 2017.01
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248385 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.
B149736

When reusing the back door glass:

i.

Using a scraper, remove any remaining adhesive residue from the back door glass.

NOTICE:

Be careful not to damage the back door glass.



ii.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:

Even if using a new back window glass, clean the back door glass with a non-residue solvent.




Hide 64828B 2.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using a brush or sponge, coat the installation area of the new back window glass clip LH with primer G.

NOTICE:

Do not apply too much primer G.



b.

Remove the peeling paper from the face of a new back window glass clip LH.

NOTICE:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.
E359124C03
0.135,0.104 0.448,0.302 0.313,0.198 10 false *a
*a Back Side of Back Door Glass
V100155

Adhesive Tape


Install the back window glass clip LH to the back door glass as shown in the illustration.

NOTICE:

Install the back window glass clip LH after primer G has been allowed to dry (approximately 3 minutes).



d.

Remove the adhesive tape.


Hide 64827B 3.INSTALL BACK WINDOW GLASS CLIP RH

a.

Using a brush or sponge, coat the installation area of the new back window glass clip RH with primer G.

NOTICE:

Do not apply too much primer G.



b.

Remove the peeling paper from the face of a new back window glass clip RH.

NOTICE:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.
B467326C03
0.125,0.073 0.438,0.271 0.313,0.198 10 false *a
*a Back Side of Back Door Glass
V100155

Adhesive Tape


Install the back window glass clip RH to the back door glass as shown in the illustration.

NOTICE:

Install the back window glass clip RH after primer G has been allowed to dry (approximately 3 minutes).



d.

Remove the adhesive tape.


Hide 64813B 4.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of a new back window glass adhesive dam with primer G.

NOTICE:

Do not apply too much primer G.



b.

Remove the peeling paper from the face of the back window glass adhesive dam.

NOTICE:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.

Install the new back window glass adhesive dam to the back door glass as shown in the illustration.

B454779C02
6.052,2.125 5.833,1.802 false 0.354,0.219 0.667,0.375 0.313,0.156 10 false *a 6.021,2.167 6.333,2.323 0.313,0.156 10 false *b 2.656,0.708 2.969,0.865 0.313,0.156 10 false A 2.667,1.052 2.854,1.24 0.188,0.188 10 true A 4.875,0.885 5.281,1.083 0.406,0.198 10 false A-A 5.615,1.063 5.927,1.219 0.313,0.156 10 false a
*a Back Side of Back Door Glass *b Adhesive Dam Application Center Line


Standard Dimension:
Area Dimension
a 6.9 mm (0.272 in.)


NOTICE:

Install the back window glass adhesive dam after primer G has been allowed to dry (approximately 3 minutes).



Hide 75575D 5.INSTALL BACK WINDOW LOWER MOULDING

a.

Using a brush or sponge, coat the installation area of a new back window lower moulding with primer G.

NOTICE:

Do not apply too much primer G.



b.

Remove the peeling paper from the face of the back window lower moulding.

NOTICE:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



c.

Install the new back window lower moulding to the back door glass as shown in the illustration.

B467322C02
0.313,0.271 0.625,0.427 0.313,0.156 10 false *a 1.969,1.927 2.125,2.083 0.156,0.156 10 true A 1.979,2.281 2.135,2.438 0.156,0.156 10 false A 4.948,0.938 5.563,1.167 0.615,0.229 10 false A-A 5.469,1.958 5.771,2.219 0.302,0.26 10 false a
*a Back Side of Back Door Glass - -


Standard Dimension:
Area Dimension
a 6.2 mm (0.244 in.)


NOTICE:

Install the back window lower moulding after primer G has been allowed to dry (approximately 3 minutes).



Hide 68131 6.INSTALL BACK DOOR GLASS

a.
B388057

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.



b.

Back door glass preliminary installation procedures:

i.

Install the suction cups to the back door glass.


ii.

Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and upper portion and sides of the back door glass is even.


iii.

When using a new back door glass:

Place matchmarks on the back door glass and vehicle body at the locations indicated in the illustration.


iv.
B454780C03
1.625,0.729 1.438,0.99 1.438,0.99 1.656,0.792 true 1.323,1 1.552,1.188 0.229,0.188 10 true *a
*a Matchmark


When reusing the back door glass:

Check the position of the matchmarks and make adjustments.


v.

Remove the back door glass.



c.

Using a brush, coat the installation surfaces on the back door panel with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Be careful when applying primer M to the panel joints and spot welds.




d.

Using a brush or sponge, coat the application area of adhesive with primer G as shown in the illustration.

B454781C02
0.354,0.479 0.667,0.635 0.313,0.156 10 false *a 2.052,2.729 2.208,2.885 0.156,0.156 10 false B 5.667,0.458 5.823,0.615 0.156,0.156 10 false a 4.656,0.51 5.177,0.708 0.521,0.198 10 false A-A: 4.667,1.396 5.188,1.594 0.521,0.198 10 false B-B: 4.688,2.583 5.208,2.781 0.521,0.198 10 false C-C: 5.719,1.448 5.875,1.604 0.156,0.156 10 false b 5.677,2.625 5.833,2.781 0.156,0.156 10 false c 5.365,3.542 5.521,3.698 0.156,0.156 10 false d 0.76,1.26 0.917,1.417 0.156,0.156 10 false c 1.146,1.396 1.302,1.552 0.156,0.156 10 true c 2.052,2.375 2.208,2.531 0.156,0.156 10 true B 2.76,1.531 2.917,1.688 0.156,0.156 10 true A 2.75,1.167 2.906,1.323 0.156,0.156 10 false A
*a Back Side of Back Door Glass - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 13.6 mm (0.535 in.)
c 22.0 mm (0.866 in.)
d 45.3 mm (1.783 in.)


NOTICE:

Do not apply too much primer G.



e.
B214800C98
1.198,0.438 1.385,0.5 false 2.51,0.542 2.854,0.26 true 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 2.865,0.146 3.104,0.323 0.24,0.177 10 false *a 1.417,0.438 1.656,0.615 0.24,0.177 10 false *b
*a Sealer Gun
*b Cartridge Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)



f.

Load the sealer gun with the cartridge.


g.

Apply adhesive to the back door glass as shown in the illustration.

B454782C03
0.76,1.26 1.073,1.417 0.313,0.156 10 false C 4.667,0.25 5.104,0.438 0.438,0.188 10 false A-A: 4.667,1.417 5.104,1.604 0.438,0.188 10 false B-B: 4.667,2.583 5.104,2.771 0.438,0.188 10 false C-C: 5.469,0.167 5.781,0.323 0.313,0.156 10 false a 5.969,0.615 6.281,0.771 0.313,0.156 10 false b 6.031,1.833 6.344,1.99 0.313,0.156 10 false b 5.646,1.073 5.958,1.229 0.313,0.156 10 false c 5.708,2.302 6.021,2.458 0.313,0.156 10 false c 5.76,3.385 6.073,3.542 0.313,0.156 10 false c 6.125,2.875 6.438,3.031 0.313,0.156 10 false b 5.531,1.417 5.844,1.573 0.313,0.156 10 false a 5.438,2.625 5.75,2.781 0.313,0.156 10 false d 1.135,1.385 1.323,1.531 0.188,0.146 10 true C 2.75,1.156 3.063,1.313 0.313,0.156 10 false A 2.76,1.531 2.938,1.708 0.177,0.177 10 true A 2.052,2.365 2.198,2.552 0.146,0.188 10 true B 2.052,2.729 2.229,2.906 0.177,0.177 10 false B 0.292,0.24 0.604,0.396 0.313,0.156 10 false *a
*a Back Side of Back Door Glass - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 14.5 mm (0.571 in.)
b 12.0 mm (0.472 in.)
c 8.0 mm (0.315 in.)
d 52.3 mm (2.059 in.)


NOTICE:

Apply the adhesive after primer G has been allowed to dry (approximately 3 minutes).



h.

Install the back door glass.

i.
B454780C03
1.625,0.729 1.438,0.99 1.438,0.99 1.656,0.792 true 1.323,1 1.552,1.188 0.229,0.188 10 true *a
*a Matchmark
V100155

Protective Tape


Using suction cups, position the back door glass so that the matchmarks are aligned and install the back door glass.

NOTICE:

Install the back door glass after primer M on the vehicle body has been allowed to dry (approximately 3 minutes).



ii.

Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




i.

w/ Rear Window Defogger:

i.

Connect the 2 connectors.



Hide 67894B 7.INSTALL NO. 2 BACK DOOR PANEL PROTECTOR

Hide 67893A 8.INSTALL NO. 1 BACK DOOR PANEL PROTECTOR

HINT:

Use the same procedure as for the No. 2 back door panel protector.


Hide 85143R 9.INSTALL REAR WIPER MOTOR GROMMET

Hide 85110R 10.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 11.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85292A 12.INSTALL REAR WIPER ARM HEAD CAP

Hide 76801 13.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 14.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.