Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248227 VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU.

DTC No. DTC Detection Condition Trouble Area
C1422 When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Brake actuator assembly (Master cylinder pressure sensor)

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1425 is output together with C1422, inspect and repair the trouble areas indicated by C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>C1425).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SW)

NG

2.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DATA LIST / ACTIVE TEST

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-


d.

Check that the stop light condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.READ VALUE USING GTS (MASTER CYLINDER SENSOR)

NG

5.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
3.READ VALUE USING GTS (MASTER CYLINDER SENSOR)
a.

Select the Data List using the GTS.(See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading/Min.: 0 V, Max.: 5 V Brake pedal released: 0.3 to 0.9 V Reading increases when brake pedal is depressed

Standard Voltage:

Master cylinder pressure sensor reading is 0.86 V or less at the instant the stop light switch changes from off to on.



b.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

Result:
Proceed to
OK
NG




OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle and perform a braking test (decelerate the vehicle by depressing the brake pedal).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC C1422 is not output. A
DTC C1422 is output. B




A

B

5.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the stop light switch assembly has been installed properly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

The stop light switch assembly installation is normal.


Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

INSTALL STOP LIGHT SWITCH ASSEMBLY CORRECTLY

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C231271C05
0.167,0.969 0.573,1.229 0.406,0.26 1.604,0.979 1.844,1.906 true 0.104,0.135 0.49,0.406 0.385,0.271 10 *a 0.26,1.031 0.698,1.344 0.438,0.313 10 A54 1.771,1.948 2.198,2.156 0.427,0.208 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-2 (STP) - Body ground Stop light switch assembly ON (Brake pedal depressed) 8 to 14 V
A54-2 (STP) - Body ground Stop light switch assembly OFF (Brake pedal released) Below 1.5 V


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)