Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a communication malfunction is detected between the headlight assembly and main body ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2430 LED Headlight LH Circuit Malfunction Any of the following conditions occur after 20 seconds have elapsed since the Ignition switch was turned ON:
·

Light control ECU malfunction

·

Headlight unit malfunction

·

Light control ECU power source and signal malfunction


·

Light control LED ECU LH

·

Headlight assembly LH

·

Instrument panel junction block assembly

·

Main body ECU

·

Harness or connector


B2431 LED Headlight RH Circuit Malfunction Any of the following conditions occur after 20 seconds have elapsed since the Ignition switch was turned ON:
·

Light control ECU malfunction

·

Headlight unit malfunction

·

Light control ECU power source and signal malfunction


·

Light control LED ECU RH

·

Headlight assembly RH

·

Instrument panel junction block assembly

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

E367516E02
1.781,2.156 3.01,2.354 1.229,0.198 10 false Solenoid 1.771,4.75 3,4.948 1.229,0.198 10 false Solenoid 0.646,1.292 0.802,1.49 0.156,0.198 10 false E 0.656,1.875 0.813,2.073 0.156,0.198 10 false E 0.469,1.302 0.615,1.51 0.146,0.208 10 false 4 0.458,1.875 0.615,2.073 0.156,0.198 10 false 1 1.656,0.656 3.344,0.854 1.688,0.198 10 false LO/HI (LED) 1.427,1.25 4.49,1.448 3.063,0.198 10 false Light Control ECU LH 1.667,3.25 3.354,3.448 1.688,0.198 10 false LO/HI (LED) 1.458,3.917 4.521,4.115 3.063,0.198 10 false Light Control ECU RH 0.469,3.896 0.625,4.094 0.156,0.198 10 false 4 0.458,4.5 0.615,4.698 0.156,0.198 10 false 1 0.656,3.885 0.813,4.083 0.156,0.198 10 false E 0.667,4.49 0.823,4.688 0.156,0.198 10 false E 3.365,1.083 3.521,1.281 0.156,0.198 10 false S 3.292,1.396 3.604,1.594 0.313,0.198 10 false LO 3.365,1.917 3.521,2.115 0.156,0.198 10 false B 3.333,3.667 3.49,3.865 0.156,0.198 10 false S 3.302,3.979 3.615,4.177 0.313,0.198 10 false LO 3.365,4.49 3.521,4.688 0.156,0.198 10 false B 3.573,1.083 3.729,1.281 0.156,0.198 10 false 2 3.573,1.396 3.729,1.594 0.156,0.198 10 false 3 3.573,1.917 3.729,2.115 0.156,0.198 10 false 5 3.688,1.646 5.219,1.844 1.531,0.198 10 false H-LP LH LO 3.698,2.167 5.229,2.365 1.531,0.198 10 false H-LP LH HI 3.677,4.25 5.208,4.448 1.531,0.198 10 false H-LP RH LO 3.688,4.76 5.219,4.958 1.531,0.198 10 false H-LP RH HI 3.521,6.49 3.979,6.688 0.458,0.198 10 false DIM 3.25,7.792 4.938,7.99 1.688,0.198 10 false H-LP/US-DRL 1.76,7.198 3.135,7.396 1.375,0.198 10 false H-LP MAIN 1.031,8 2.865,8.198 1.833,0.198 10 false from Battery 4.833,7.521 5.917,8.448 1.083,0.927 10 false Instrument Panel Junction Block Assembly 5.958,8.094 7.115,8.427 1.156,0.333 10 false Main Body ECU 3.219,5.688 3.375,5.885 0.156,0.198 10 false 3 3.229,7.365 3.385,7.563 0.156,0.198 10 false 3 3.24,6.094 3.396,6.292 0.156,0.198 10 false 1 3.219,6.948 3.375,7.146 0.156,0.198 10 false 1 3.99,5.688 4.146,5.885 0.156,0.198 10 false 5 4.01,7.365 4.167,7.563 0.156,0.198 10 false 5 3.99,6.094 4.146,6.292 0.156,0.198 10 false 2 3.99,6.948 4.146,7.146 0.156,0.198 10 false 2 5.563,1.177 6.177,1.375 0.615,0.198 10 false F136 5.573,3.792 6.188,3.99 0.615,0.198 10 false F136 5.625,6.188 5.938,6.385 0.313,0.198 10 false MB 5.604,7.063 5.917,7.26 0.313,0.198 10 false MB 5.031,6.188 5.344,6.385 0.313,0.198 10 false 3C 5.031,7.052 5.344,7.25 0.313,0.198 10 false 3C 5.656,1 5.969,1.198 0.313,0.198 10 false 24 5.656,3.594 5.969,3.792 0.313,0.198 10 false 21 5.656,6.01 5.969,6.208 0.313,0.198 10 false 22 5.052,6.01 5.365,6.208 0.313,0.198 10 false 35 5.615,6.875 5.927,7.073 0.313,0.198 10 false 15 5.021,6.875 5.333,7.073 0.313,0.198 10 false 18 6.021,1.177 6.635,1.375 0.615,0.198 10 false LLEW 5.99,3.792 6.604,3.99 0.615,0.198 10 false RLEW 6,6.188 6.458,6.385 0.458,0.198 10 false DIM 5.99,7.052 6.604,7.25 0.615,0.198 10 false HRLY 3.573,4.49 3.729,4.688 0.156,0.198 10 false 5 3.573,3.667 3.729,3.865 0.156,0.198 10 false 2 3.573,3.979 3.729,4.177 0.156,0.198 10 false 3 1.25,2.438 1.708,2.635 0.458,0.198 10 false A85 1.271,5.052 1.729,5.25 0.458,0.198 10 false A84 1.26,2.604 4.469,2.802 3.208,0.198 10 false Headlight Assembly LH 1.271,5.229 4.479,5.427 3.208,0.198 10 false Headlight Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC B2430 and B2431 are not output if 20 seconds have not elapsed since the Ignition switch was turned ON.



PROCEDURE

1.CHECK FOR DTC


Result
Result Proceed to
Both DTCs B2430 and B2431 are not output. A
Both DTCs B2430 and B2431 are output. B
Only DTC B2430 or B2431 is output. C


A

B

2.INSPECT HEADLIGHT RELAY (H-LP/US-DRL RELAY)

C

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH - HEADLIGHT RELAY (H-LP/US-DRL RELAY))
2.INSPECT HEADLIGHT RELAY (H-LP/US-DRL RELAY)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Inspect the headlight relay (H-LP/US-DRL relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY (H-LP/US-DRL RELAY))

NG

REPLACE HEADLIGHT RELAY (H-LP/US-DRL RELAY)

3.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY (H-LP/US-DRL RELAY))
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.
E219671C02
0.135,0.104 0.323,0.26 0.188,0.156 10 false *1 0.802,2.208 0.99,2.365 0.188,0.156 10 false *2
*1 No. 2 Engine Room Relay Block
*2 Headlight Relay (H-LP/US-DRL Relay) Holder


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H-LP/US-DRL-1 - Body ground Always 11 to 14 V
H-LP/US-DRL-3 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY (H-LP/US-DRL RELAY) - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY (H-LP/US-DRL RELAY) - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Disconnect the A85 headlight assembly LH connector.


c.

Disconnect the A84 headlight assembly RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay Terminal 5 - A85-3 (LO) Always Below 1 Ω
Relay Terminal 5 - A84-3 (LO) Always Below 1 Ω
Relay Terminal 5 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY (H-LP/US-DRL RELAY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY (H-LP/US-DRL RELAY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-LP/US-DRL-2 - 3C-18 Always Below 1 Ω
H-LP/US-DRL-2 or 3C-18 - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

U158608C02
5.24,1.26 4.958,0.979 true 4.979,0.385 5.208,0.563 0.229,0.177 10 false MB 1.698,0.24 1.896,0.417 0.198,0.177 10 false 3C 0.104,0.073 0.344,0.26 0.24,0.188 10 false *a 5.271,1.198 5.698,1.354 0.427,0.156 10 false HRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω




OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH - HEADLIGHT RELAY (H-LP/US-DRL RELAY))
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Disconnect the A85 headlight assembly LH connector.


c.

Disconnect the A84 headlight assembly RH connector.


d.
E366993C04
0.667,0.75 1.167,1 0.5,0.25 0.667,1.167 1.167,1.417 0.5,0.25 2.625,1.01 2.896,0.583 true 2.969,0.448 3.313,0.646 0.344,0.198 10 false LO 0.792,0.813 1.25,1.01 0.458,0.198 10 false A85 0.792,1.219 1.25,1.417 0.458,0.198 10 false A84 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 1.25,0.802 1.563,1 0.313,0.198 10 false *b 1.25,1.208 1.563,1.406 0.313,0.198 10 false *c
*a Front view of wire harness connector
(to Headlight Assembly)
*b for LH
*c for RH


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A85-3 (LO) - Body ground Light control switch in head position 11 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A84-3 (LO) - Body ground Light control switch in head position 11 to 14 V




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the A85 headlight assembly LH connector.


b.

Disconnect the A84 headlight assembly RH connector.


c.
E366993C05
0.667,0.75 1.167,1 0.5,0.25 0.667,1.167 1.167,1.417 0.5,0.25 2.24,1.76 2.188,1.323 true 2.229,1.771 2.573,1.969 0.344,0.198 10 false E 0.792,0.813 1.25,1.01 0.458,0.198 10 false A85 0.792,1.219 1.25,1.417 0.458,0.198 10 false A84 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 1.25,0.802 1.563,1 0.313,0.198 10 false *b 1.25,1.208 1.563,1.406 0.313,0.198 10 false *c
*a Front view of wire harness connector
(to Headlight Assembly)
*b for LH
*c for RH


Measure the voltage according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
A85-4 (E) - Body ground Always Below 1 Ω

RH Side (B2431)
Tester Connection Condition Specified Condition
A84-4 (E) - Body ground Always Below 1 Ω




OK

9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE)
a.

Disconnect the A85 headlight assembly LH connector.


b.

Disconnect the A84 headlight assembly RH connector.


c.
E366993C03
0.667,0.75 1.167,1 0.5,0.25 0.667,1.167 1.167,1.417 0.5,0.25 2.396,0.969 2.885,0.26 true 2.958,0.156 3.302,0.354 0.344,0.198 10 false S 0.792,0.813 1.25,1.01 0.458,0.198 10 false A85 0.792,1.219 1.25,1.417 0.458,0.198 10 false A84 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 1.25,0.802 1.563,1 0.313,0.198 10 false *b 1.25,1.208 1.563,1.406 0.313,0.198 10 false *c
*a Front view of wire harness connector
(to Headlight Assembly)
*b for LH
*c for RH


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH (B2430)
Tester Connection Condition Specified Condition
A85-2 (S) - Body ground Ignition switch on, light control switch in head position 11 to 14 V

for RH (B2431)
Tester Connection Condition Specified Condition
A84-2 (S) - Body ground Ignition switch on, light control switch in head position 11 to 14 V




OK

11.CHECK HEADLIGHT ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - MAIN BODY ECU)
10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the A85 headlight assembly LH connector.


b.

Disconnect the A84 headlight assembly RH connector.


c.

Disconnect the F136 main body ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH (B2430)
Tester Connection Condition Specified Condition
A85-2 (S) - F136-24 (LLEW) Always Below 1 Ω
A85-2 (S) or F136-24 (LLEW) - Body ground Always 10 kΩ or higher

for RH (B2431)
Tester Connection Condition Specified Condition
A84-2 (S) - F136-21 (RLEW) Always Below 1 Ω
A84-2 (S) or F136-21 (RLEW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HEADLIGHT ASSEMBLY
a.

Replace the headlight assembly with a new or known good one.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL


b.

Check for DTCs

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B2430 or B2431 is not output.




OK

END (HEADLIGHT ASSEMBLY WAS DEFECTIVE)

NG