52601
1.INSTALL FRONT BUMPER ENERGY ABSORBER SUB-ASSEMBLY
Engage the 3 hooks to install the front bumper energy absorber sub-assembly.
Install the 6 screws, 6 clips and grommet.
57014A
2.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH
Engage the 2 guides to install the front side member bracket sub-assembly LH.
Install the 4 bolts.
57013C
3.INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
53165A
4.INSTALL FRONT NO. 1 BUMPER STONE DEFLECTOR BRACKET
Install the front No. 1 bumper stone deflector bracket with the 2 nuts.
Use the same procedure for the opposite side.
52131A
5.INSTALL FRONT BUMPER REINFORCEMENT
Temporarily install the front bumper reinforcement with the 4 nuts and 6 bolts.
Fully tighten the 4 nuts.
Fully tighten the 6 bolts.
Engage the 2 clamps to install the wire harness.
51442C
6.INSTALL ENGINE UNDER COVER LH
for 1NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
for 2NZ-FE:
Click hereEngine / Hybrid System>2NZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
51441C
7.INSTALL ENGINE UNDER COVER RH
for 1NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
for 2NZ-FE:
Click hereEngine / Hybrid System>2NZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION
52611
8.INSTALL FRONT BUMPER ENERGY ABSORBER
Engage the 2 guides to install the front bumper energy absorber.
16695A
9.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH
Engage the 2 claws to install the front radiator side air guide plate LH.
16691A
10.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH
Use the same procedure as for the LH side.
16595B
11.INSTALL NO. 1 RADIATOR AIR GUIDE LH
Engage the 2 claws to install the No. 1 radiator air guide LH.
16593B
12.INSTALL NO. 1 RADIATOR AIR GUIDE RH
Use the same procedure as for the LH side.
88790B
13.INSTALL THERMISTOR ASSEMBLY
Engage the clamp to install the thermistor assembly.
Engage the clamp to install the wire harness.
Connect the connector.
52536
14.INSTALL FRONT BUMPER SIDE RETAINER LH
Engage the 2 claws to install the front bumper side retainer LH.
52535
15.INSTALL FRONT BUMPER SIDE RETAINER RH
Use the same procedure as for the LH side.
81150
16.INSTALL HEADLIGHT ASSEMBLY LH
81110
17.INSTALL HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
52713A
18.INSTALL FRONT BUMPER SIDE MOULDING LH (w/ Fog Light)
Engage the 6 claws to install the front bumper side moulding LH.
52712
19.INSTALL FRONT BUMPER SIDE MOULDING RH (w/ Fog Light)
Use the same procedure as for the LH side.
81482C
20.INSTALL FOG LIGHT COVER LH (w/ Fog Light)
Engage the guide and 8 claws to install the fog light cover LH.
Install the outside moulding retainer.
81481E
21.INSTALL FOG LIGHT COVER RH (w/ Fog Light)
Use the same procedure as for the LH side.
81482C
22.INSTALL FOG LIGHT COVER LH (w/o Fog Light)
Engage the guide and 8 claws to install the fog light cover LH.
81481E
23.INSTALL FOG LIGHT COVER RH (w/o Fog Light)
Use the same procedure as for the LH side.
81220
24.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
81210A
25.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)
Use the same procedure as for the LH side.
53879H
26.INSTALL FRONT FENDER LINER RETAINER
Engage the claw to install the front fender liner retainer.
Use the same procedure for both sides.
75311
27.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
Engage the 2 guides and 4 claws to install the radiator grille (or front panel) emblem.
53126B
28.INSTALL CENTER RADIATOR GRILLE MOULDING LH
Engage the claw to install the center radiator grille moulding LH.
Install the 2 screws.
53125B
29.INSTALL CENTER RADIATOR GRILLE MOULDING RH
Use the same procedure as for the LH side.
53112E
30.INSTALL LOWER NO. 1 RADIATOR GRILLE
Engage the 2 guides and 24 claws to install the lower No. 1 radiator grille.
Install the 2 clips.
52129B
31.INSTALL FRONT BUMPER LOWER COVER
Engage the hook.
Engage the 2 guides and claw to install the front bumper lower cover.
53111
32.INSTALL RADIATOR GRILLE
Engage the 2 guides and 5 claws to install the radiator grille.
Install the 3 clips.
Install the 2 screws.
53395E
33.INSTALL HOOD TO FRONT END PANEL SEAL
Engage the 14 clips to install the hood to front end panel seal.