Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.09
RM19S0E _51 Engine / Hybrid System _051451 2NZ-FE ENGINE MECHANICAL _0248090 ENGINE ASSEMBLY A

2NZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.

Install the engine mounting insulator LH with the 5 bolts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator RH is necessary.


a.

Install the engine mounting insulator RH with the 3 bolts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12321B 3.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.

Install the drive shaft heat insulator sub-assembly with the bolt and nut.

Torque:
18 N*m (183 kgf*cm, 13 ft.*lbf)


Hide 87245A 4.CONNECT INLET HEATER WATER HOSE A

a.

Connect heater water inlet hose A to the cylinder head.


Hide 17167 5.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the exhaust manifold insulator with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 6.FIX ENGINE ASSEMBLY

a.

Using an engine sling device and a chain block, hold the engine assembly.


b.

Use a belt with a tightening mechanism or a rope to secure the engine assembly with transaxle to the engine lifter.

NOTICE:
·

Set plate lift attachments so that the engine assembly with transaxle is level.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.




Hide 32101B 7.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

a.
A260427E02
1.26,1.271 0.906,1.51 false 1.781,1.948 2,1.948 false 2.24,1.115 2.521,1.344 false 0.74,1.469 0.927,1.646 0.188,0.177 10 false *1 2.021,1.865 2.177,2.01 0.156,0.146 10 false *2 2.552,1.333 2.708,1.479 0.156,0.146 10 false *3

Using SST, hold the crankshaft.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Clean the 6 bolts and their holes.


c.

Install the front drive plate spacer.

Text in Illustration
*1 Front Drive Plate Spacer
*2 Drive Plate and Ring Gear
*3 Rear Drive Plate Spacer
V100135

Engine Side
V100136

Transaxle Side


d.

Install the drive plate and rear drive plate spacer onto the crankshaft.

HINT:
·

The front drive plate spacer is reversible.

·

As the drive plate and ring gear and the rear drive plate spacer are not reversible, make sure to install them in the direction as shown in the illustration.




e.
A057108E51
1.99,0.427 1.698,1.302 false 1.979,0.24 2.167,0.406 0.188,0.167 10 false *a

Apply adhesive to the end 2 or 3 threads of the 6 bolts.

Text in Illustration
*a Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the drive plate spacer RR, drive plate and ring gear sub-assembly and drive plate spacer FR.


g.
A158035E09
1.813,0.531 1.938,0.719 0.125,0.188 10 false 1 1.417,1.26 1.542,1.448 0.125,0.188 10 false 2 2.24,1.281 2.365,1.469 0.125,0.188 10 false 3 1.406,0.792 1.531,0.979 0.125,0.188 10 false 4 1.833,1.51 1.958,1.698 0.125,0.188 10 false 5 2.24,0.771 2.365,0.958 0.125,0.188 10 false 6

Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after performing the installation.



Hide 13405 8.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.
A107285E07
1.698,1.823 2.083,1.823 true 2.135,1.75 2.583,1.969 0.448,0.219 10 true SST

Hold the crankshaft with SST.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Clean the 6 bolts and their holes.


c.
A057108E51
1.99,0.427 1.698,1.302 false 1.979,0.24 2.167,0.406 0.188,0.167 10 false *a

Apply adhesive to the end 2 or 3 threads of new bolts.

Text in Illustration
*a Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A381869E01
1.688,0.406 1.844,0.604 0.156,0.198 10 false 1 2.198,0.698 2.354,0.896 0.156,0.198 10 false 6 2.198,1.333 2.354,1.531 0.156,0.198 10 false 3 1.688,1.635 1.844,1.833 0.156,0.198 10 false 5 1.167,1.385 1.271,1.552 0.104,0.167 10 false 2 1.135,0.74 1.292,0.906 0.156,0.167 10 false 4

Install the flywheel with the 6 bolts in the order shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 38 ft.*lbf)


e.

Mark a paint mark on each bolt head on the engine upper side.


f.
A381868E01
2.323,0.729 2.604,0.917 0.281,0.188 10 false 90°

Tighten the bolts 90° in the sequence shown in the illustration.

NOTICE:

Do not start the engine for at least 1 hour after performing the installation.



Hide 31250 9.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 10.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 11.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 30500 12.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

C248193E03
1.729,1.052 2.698,0.677 true 2.74,0.573 2.917,0.729 0.177,0.156 10 false *1 0.948,1 1.125,1.156 0.177,0.156 10 false *2

a.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

Text in Illustration
*1 Torque Converter Centerpiece
*2 Crankshaft

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum spread:

About 1 g (0.0353 oz.)



b.
A260428E02
1.188,0.615 2.583,0.365 2.583,0.365 2.375,0.885 true 2.625,0.26 2.813,0.458 0.188,0.198 10 false *1

While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 7 bolts shown in the illustration.

Text in Illustration
*1 Knock Pin

Torque:
30 N*m (301 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the transaxle.

·

Do not forcibly pry on the Check that the torque converter rotates.

·

Check that the torque converter rotates.




c.

Install the wire harness bracket with the bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

To avoid damage to the input shaft, do not forcefully shake the transaxle.

·

Insert knock pins into the knock pin holes securely so that the end face of the transaxle fits close against the engine before tightening the bolts.




Hide 30300 13.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

a.

Install the manual transaxle assembly with the 7 bolts.

Torque:
33 N*m (336 kgf*cm, 24 ft.*lbf)


Hide 33524F 14.INSTALL CONTROL CABLE BRACKET (for Manual Transaxle)

a.

Install the floor shift control lever housing support bracket with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 28100 15.INSTALL STARTER ASSEMBLY

Hide 11363A 16.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 17141 17.INSTALL EXHAUST MANIFOLD

A369829E02
0.688,0.729 0.688,0.5 false 1.813,0.74 1.813,0.5 false 2.875,0.76 2.875,0.542 false 2.313,1.417 2.313,1.188 false 1.198,1.406 1.198,1.177 false 1.771,0.313 1.979,0.552 0.208,0.24 10 false 1 0.656,0.323 0.865,0.563 0.208,0.24 10 false 4 2.844,0.354 3.052,0.594 0.208,0.24 10 false 5 2.281,1.448 2.49,1.688 0.208,0.24 10 false 3 1.167,1.448 1.375,1.688 0.208,0.24 10 false 2

a.

Tighten the exhaust manifold nuts and bolts, in the order shown in the illustration, through a new gasket.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 25591 18.INSTALL MANIFOLD SUPPORT BRACKET

a.

Install the manifold support bracket with the 3 bolts.

Torque:
44 N*m (449 kgf*cm, 33 ft.*lbf)


Hide 17167 19.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 17111 20.INSTALL INTAKE MANIFOLD

a.

Install a new gasket onto the intake manifold.


b.
A105631E16
1.573,0.24 1.708,0.427 0.135,0.188 10 true 1 0.906,0.052 1.042,0.219 0.135,0.167 10 true 2 2.24,0.052 2.365,0.219 0.125,0.167 10 true 3 0.042,1.083 0.167,1.26 0.125,0.177 10 true 4 3.125,1.073 3.26,1.25 0.135,0.177 10 true 5

Provisionally tighten the intake manifold nuts and bolts in the order shown in the illustration, and then tighten them to the specified torque.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


c.

Connect the water by-pass hose to No. 1 water bypass pipe.


d.

Connect the water by-pass hose to the cylinder head.


e.

Connect the union to connector tube hose to the booster vacuum tube with the hose clamp.


Hide 16502 21.INSTALL WATER FILLER SUB-ASSEMBLY

a.

Install the water filler sub-assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the No. 1 radiator hose to the cylinder head with the hose clamp.


Hide 51201 23.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Install the engine moving control rod with the through bolt.

Torque:
120 N*m (1244 kgf*cm, 89 ft.*lbf)


Hide 24.INSTALL ENGINE WIRE

a.

Connect all the wire harnesses and connectors.


b.

Install the 2 ground bolts.

Torque:
8.4 N*m (85 kgf*cm, 74 in.*lbf)


Hide 12281A 25.REMOVE NO. 1 ENGINE HANGER

a.

Remove the 2 bolts and the No. 1 engine hanger.


b.

Install the oxygen sensor wiring bracket with the 2 bolts.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


Hide 26.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

SST
09670-00010  

a.

Place wooden blocks or plate lift attachments on an engine lifter, and then set the engine assembly with transaxle.

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the engine assembly with transaxle is level.

·

As the engine assembly with transaxle is very heavy, be sure to support it securely.




b.

Operate the engine lifter and lift the engine assembly with transaxle and the front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.


c.

Install the engine mounting insulator LH with the through bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Tighten by holding the nut and turning the bolt.



d.

Install the engine mounting insulator RH with the bolt and 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


e.

By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

C233133E06
4.312,1.479 4.466,1.624 0.154,0.145 10 *a 4.458,1.502 4.568,1.303 false 2.799,1.479 2.953,1.624 0.154,0.145 10 *a 5.562,2.051 5.685,2.196 0.124,0.145 10 A 5.333,2.457 5.457,2.603 0.124,0.145 10 B 5.361,2.654 5.485,2.799 0.124,0.145 10 C 1.513,1.981 1.636,2.126 0.124,0.145 10 A 1.774,2.429 1.898,2.575 0.124,0.145 10 B 3.803,2.574 4.103,2.719 0.300,0.145 10 SST 4.091,2.638 4.72,2.638 false 3.159,2.574 3.459,2.719 0.300,0.145 10 SST 5.76,3.517 5.989,3.662 0.228,0.145 10 *c 5.018,3.517 5.246,3.662 0.228,0.145 10 *a 2.468,3.517 2.696,3.662 0.228,0.145 10 *c 1.725,3.517 1.954,3.662 0.228,0.145 10 *b 1.774,2.64 1.898,2.785 0.124,0.145 10 C 2.782,1.502 2.693,1.288 false 3.135,2.638 2.508,2.638 false

Text in Illustration
*a Datum Hole *b OK
*c NG - -
V100135

Front of the Vehicle - -

Torque:
Bolt A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
Bolt B : 151 N*m (1540 kgf*cm, 111 ft.*lbf)
Bolt C : 98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:
·

Insert SST into the datum hole vertically.

·

If impossible to insert SST vertically, loosen all bolts and then insert SST again.




Hide 45025D 27.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45209 28.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 29.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 32101G 30.INSTALL TORQUE CONVERTER SETTING BOLT (for Automatic Transaxle)

A057108E51
1.99,0.427 1.698,1.302 false 1.979,0.24 2.167,0.406 0.188,0.167 10 false *a

a.

Remove any adhesive remaining in the 6 bolt holes of the torque converter clutch and 6 bolts.


b.

Apply adhesive to 2 or 3 threads on the end of the 6 bolts.

Text in Illustration
*a Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Hold the crankshaft pulley with SST.

SST
09960-10010  (09962-01000, 09963-01000)


d.

Tighten the 6 torque converter set bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 11361J 31.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 43420 32.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 17451 33.INSTALL EXHAUST PIPE GASKET

Hide 17451A 34.INSTALL NO. 2 EXHAUST PIPE GASKET

Hide 17410 35.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 36.INSTALL FRONT FLOOR CENTER BRACE

Hide 33820B 37.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

Hide 33820B 38.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

Hide 33820B 39.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

Hide 58910C 40.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 41.CONNECT ENGINE WIRE

a.

for Automatic Transaxle:

i.

Engage the clamp and connect the wire harness to the automatic transaxle.


ii.

Install the wire harness to the automatic transaxle with the bolt.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)



b.

Connect the 2 connectors to the battery positive terminal.


c.

Engage the 2 claws and connect the wire harness to the engine room relay block.


d.

Connect the connector to the engine room relay block.


e.

Engage the clamp and connect the wire harness to the body.


f.

Pull down the lever to engage the lock and connect the connector to the ECM.


g.

Engage the clamp and connect the wire harness to the wire harness bracket.


h.

Connect all the wire harness and connectors.


Hide 88310 42.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

Hide 31470 43.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 16361A 44.INSTALL FAN AND GENERATOR V BELT

Hide 16361A 45.ADJUST FAN AND GENERATOR V BELT

Hide 87245A 46.CONNECT INLET HEATER WATER HOSE A

a.

Connect inlet heater water hose A to the heater unit with the hose clamp.


Hide 87246A 47.CONNECT OUTLET HEATER WATER HOSE A

a.

Connect outlet heater water hose A to the heater unit with the hose clamp.


Hide 44773F 48.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the booster vacuum tube with the hose clamp.


Hide 23901 49.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube connector and fuel pipe.

CAUTION:

Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a click sound. If the connection is tight, apply a small amount of engine oil to the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.



Hide 23842A 50.INSTALL EFI FUEL PIPE CLAMP

a.

Install the EFI fuel pipe clamp.


Hide 51.CONNECT INLET OIL COOLER HOSE (for Automatic Transaxle)

a.

Connect the oil cooler inlet hose with the clip.


Hide 52.CONNECT OUTLET OIL COOLER HOSE (for Automatic Transaxle)

a.

Connect the oil cooler outlet hose with the clip.


Hide 16572D 53.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet with the hose clamp.


Hide 16573B 54.CONNECT NO. 3 RADIATOR HOSE

a.

Connect No. 3 radiator hose to the water filler with the hose clamp.


Hide 55.CONNECT RADIATOR RESERVOIR TANK HOSE

a.

Connect the radiator reservoir tank hose to the water filler.


Hide 23820 56.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY

a.

Install fuel vapor feed hose assembly with the 2 hose clamps.


Hide 74411 57.INSTALL BATTERY CARRIER

a.

Install the battery carrier with the 5 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


b.

Engage the 7 wire harness clamps and install the wire harness.


Hide 17771A 58.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket with the 2 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


b.

Connect the wire harness clamp to the air cleaner bracket.


Hide 17700 59.INSTALL AIR CLEANER ASSEMBLY

a.

Install the air cleaner case onto the air cleaner bracket with the 2 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the clamp and connect the wire harness to the air cleaner case.


c.

Install the air cleaner element onto the air cleaner case.


d.

Install the air cleaner cap sub-assembly with No. 1 air cleaner hose onto the throttle body assembly.


e.

Engage the 2 clamps and connect the air cleaner cap sub-assembly to the air cleaner case subassembly.


f.

Tighten the hose clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


g.

Connect the vacuum switching valve assembly connector.


h.

Connect the mass air flow meter connector.


i.

Engage the 2 clamps and connect the wire harness to the air cleaner cap sub-assembly and vacuum switching valve assembly.


j.

Connect the No. 2 fuel vapor feed hose to the intake manifold.


k.

Connect the fuel vapor feed hose assembly to the No. 1 air cleaner hose and vacuum switching valve assembly with the 2 hose clamps.


l.

Engage the clamp and connect the fuel vapor feed hose assembly to the No. 1 air cleaner hose.


Hide 74431 60.INSTALL BATTERY TRAY

Hide 28800 61.INSTALL BATTERY

a.

Install the battery onto the vehicle with the battery clamp.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


b.

Connect the cable to the battery terminal.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 55711 62.INSTALL OUTER COWL TOP PANEL

Hide 55722C 63.INSTALL INNER COWL TOP TO COWL BRACE

Hide 55815E 64.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 55735D 65.INSTALL FRONT AIR SHUTTER SEAL RH

Hide 66.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 67.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 16361A 68.INSPECT FAN AND GENERATOR V BELT

Hide 71.ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 72.INSPECT AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 73.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 74.INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 76.INSPECT FOR OIL LEAK

Hide 77.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK

Hide 78.INSPECT FOR MANUAL TRANSAXLE OIL LEAK

Hide 80.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Hide 84.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51441C 85.INSTALL ENGINE UNDER COVER RH

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Hide 51442C 86.INSTALL ENGINE UNDER COVER LH

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)