Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Only perform this procedure when replacement of the engine mounting insulator LH is necessary.
Install the engine mounting insulator LH with the 5 bolts.
12305
2.INSTALL ENGINE MOUNTING INSULATOR RH
Only perform this procedure when replacement of the engine mounting insulator RH is necessary.
Install the engine mounting insulator RH with the 3 bolts.
12321B
3.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Install the drive shaft heat insulator sub-assembly with the bolt and nut.
87245A
4.CONNECT INLET HEATER WATER HOSE A
Connect heater water inlet hose A to the cylinder head.
5.FIX ENGINE ASSEMBLY
Using an engine sling device and a chain block, hold the engine assembly.
Use a belt with a tightening mechanism or a rope to secure the engine assembly with transaxle to the engine lifter.
Set plate lift attachments so that the engine assembly with transaxle is level.
Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent deformation of the oil pan, never set any attachments against the oil pan of the engine assembly.
32101B
6.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)
Using SST, hold the crankshaft.
Clean the 6 bolts and their holes.
Install the front drive plate spacer.
| *1 | Front Drive Plate Spacer |
| *2 | Drive Plate and Ring Gear |
| *3 | Rear Drive Plate Spacer |
|
Engine Side |
|
Transaxle Side |
Install the drive plate and rear drive plate spacer onto the crankshaft.
The front drive plate spacer is reversible.
As the drive plate and ring gear and the rear drive plate spacer are not reversible, make sure to install them in the direction as shown in the illustration.
Apply adhesive to the end 2 or 3 threads of the 6 bolts.
| *a | Adhesive |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the drive plate spacer RR, drive plate and ring gear sub-assembly and drive plate spacer FR.
Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.
Do not start the engine for at least 1 hour after performing the installation.
13405
7.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
Hold the crankshaft with SST.
Clean the 6 bolts and their holes.
Apply adhesive to the end 2 or 3 threads of new bolts.
| *a | Adhesive |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the flywheel with the 6 bolts in the order shown in the illustration.
Mark a paint mark on each bolt head on the engine upper side.
Tighten the bolts 90° in the sequence shown in the illustration.
Do not start the engine for at least 1 hour after performing the installation.
31250
8.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)
31210
9.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31210
10.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)
30500
11.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
Toyota Genuine Clutch Spline Grease or equivalent
About 1 g (0.0353 oz.)
While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 7 bolts shown in the illustration.
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the transaxle.
Do not forcibly pry on the Check that the torque converter rotates.
Check that the torque converter rotates.
Install the wire harness bracket with the bolt.
To avoid damage to the input shaft, do not forcefully shake the transaxle.
Insert knock pins into the knock pin holes securely so that the end face of the transaxle fits close against the engine before tightening the bolts.
30300
12.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
Install the manual transaxle assembly with the 7 bolts.
33524F
13.INSTALL CONTROL CABLE BRACKET (for Manual Transaxle)
28100
14.INSTALL STARTER ASSEMBLY
11363A
15.INSTALL FLYWHEEL HOUSING SIDE COVER
17141
16.INSTALL EXHAUST MANIFOLD
Tighten the exhaust manifold nuts and bolts, in the order shown in the illustration, through a new gasket.
25591
17.INSTALL MANIFOLD SUPPORT BRACKET
Install the manifold support bracket with the 3 bolts.
17167
18.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 1 exhaust manifold heat insulator.
17111
19.INSTALL INTAKE MANIFOLD
Install a new gasket onto the intake manifold.
Provisionally tighten the intake manifold nuts and bolts in the order shown in the illustration, and then tighten them to the specified torque.
Connect the water by-pass hose to No. 1 water bypass pipe.
Connect the water by-pass hose to the cylinder head.
Connect the union to connector tube hose to the booster vacuum tube with the hose clamp.
16502
20.INSTALL WATER FILLER SUB-ASSEMBLY
Install the water filler sub-assembly with the 2 nuts.
Connect the No. 1 radiator hose to the cylinder head with the hose clamp.
19500D
21.INSTALL NO. 1 IGNITION COIL
51201
22.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Install the engine moving control rod with the through bolt.
23.INSTALL ENGINE WIRE
Connect all the wire harnesses and connectors.
Install the 2 ground bolts.
12281A
24.REMOVE NO. 1 ENGINE HANGER
Remove the 2 bolts and the No. 1 engine hanger.
Install the oxygen sensor wiring bracket with the 2 bolts.
25.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Place wooden blocks or plate lift attachments on an engine lifter, and then set the engine assembly with transaxle.
Place the wooden blocks or plate lift attachments so that the engine assembly with transaxle is level.
As the engine assembly with transaxle is very heavy, be sure to support it securely.
Operate the engine lifter and lift the engine assembly with transaxle and the front suspension crossmember to the position where the engine mounting insulators RH and LH can be installed.
Install the engine mounting insulator LH with the through bolt and nut.
Tighten by holding the nut and turning the bolt.
Install the engine mounting insulator RH with the bolt and 2 nuts.
By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.
| *a | Datum Hole | *b | OK |
| *c | NG | - | - |
|
Front of the Vehicle | - | - |
Insert SST into the datum hole vertically.
If impossible to insert SST vertically, loosen all bolts and then insert SST again.
45025D
26.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45209
27.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY
45259A
28.INSTALL COLUMN HOLE COVER SILENCER SHEET
32101G
29.INSTALL TORQUE CONVERTER SETTING BOLT (for Automatic Transaxle)
Remove any adhesive remaining in the 6 bolt holes of the torque converter clutch and 6 bolts.
Apply adhesive to 2 or 3 threads on the end of the 6 bolts.
| *a | Adhesive |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Hold the crankshaft pulley with SST.
Tighten the 6 torque converter set bolts.
11361J
30.INSTALL FLYWHEEL HOUSING UNDER COVER
43420
31.INSTALL FRONT DRIVE SHAFT ASSEMBLY
17451
32.REMOVE EXHAUST PIPE GASKET
17451A
33.REMOVE NO. 2 EXHAUST PIPE GASKET
17410
34.INSTALL FRONT EXHAUST PIPE ASSEMBLY
57533B
35.INSTALL FRONT FLOOR CENTER BRACE
33820B
36.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)
33820B
37.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY
33820B
38.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
58910C
39.INSTALL REAR CONSOLE BOX ASSEMBLY
40.CONNECT ENGINE WIRE
for Automatic Transaxle:
Engage the clamp and connect the wire harness to the automatic transaxle.
Install the wire harness to the automatic transaxle with the bolt.
Connect the 2 connectors to the battery positive terminal.
Engage the 2 claws and connect the wire harness to the engine room relay block.
Connect the connector to the engine room relay block.
Engage the clamp and connect the wire harness to the body.
Pull down the lever to engage the lock and connect the connector to the ECM.
Engage the clamp and connect the wire harness to the wire harness bracket.
Connect all the wire harness and connectors.
88310
41.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY
31470
42.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)
16361A
43.INSTALL FAN AND GENERATOR V BELT
16361A
44.ADJUST FAN AND GENERATOR V BELT
87245A
45.CONNECT INLET HEATER WATER HOSE A
Connect inlet heater water hose A to the heater unit with the hose clamp.
87246A
46.CONNECT OUTLET HEATER WATER HOSE A
Connect outlet heater water hose A to the heater unit with the hose clamp.
44773F
47.CONNECT UNION TO CHECK VALVE HOSE
Connect the union to check valve hose to the booster vacuum tube with the hose clamp.
23901
48.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube connector and fuel pipe.
Align the fuel tube connector with the pipe, then push the fuel tube connector in until the retainer makes a click sound. If the connection is tight, apply a small amount of engine oil to the tip of the pipe. After connecting, pull the pipe and connector to make sure that they are securely connected.
23842A
49.INSTALL EFI FUEL PIPE CLAMP
Install the EFI fuel pipe clamp.
32921D
50.CONNECT INLET OIL COOLER HOSE (for Automatic Transaxle)
Connect the inlet oil cooler hose with the clip.
32922A
51.CONNECT OUTLET OIL COOLER HOSE (for Automatic Transaxle)
Connect the outlet oil cooler hose with the clip.
16572D
52.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet with the hose clamp.
16573B
53.CONNECT NO. 3 RADIATOR HOSE
Connect No. 3 radiator hose to the water filler with the hose clamp.
54.CONNECT RADIATOR RESERVOIR TANK HOSE
Connect the radiator reservoir tank hose to the water filler.
23820
55.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
Install fuel vapor feed hose assembly with the 2 hose clamps.
74411
56.INSTALL BATTERY CARRIER
Install the battery carrier with the 5 bolts.
Engage the 7 wire harness clamps and install the wire harness.
17771A
57.INSTALL AIR CLEANER BRACKET
Install the air cleaner bracket with the 2 bolts.
Connect the wire harness clamp to the air cleaner bracket.
17700
58.INSTALL AIR CLEANER ASSEMBLY
Install the air cleaner case onto the air cleaner bracket with the 2 bolts.
Engage the clamp and connect the wire harness to the air cleaner case.
Install the air cleaner element onto the air cleaner case.
Install the air cleaner cap sub-assembly with No. 1 air cleaner hose onto the throttle body assembly.
Engage the 2 clamps and connect the air cleaner cap sub-assembly to the air cleaner case subassembly.
Tighten the hose clamp.
Connect the vacuum switching valve assembly connector.
Connect the mass air flow meter connector.
Engage the 2 clamps and connect the wire harness to the air cleaner cap sub-assembly and vacuum switching valve assembly.
Connect the No. 2 fuel vapor feed hose to the intake manifold.
Connect the fuel vapor feed hose assembly to the No. 1 air cleaner hose and vacuum switching valve assembly with the 2 hose clamps.
Engage the clamp and connect the fuel vapor feed hose assembly to the No. 1 air cleaner hose.
74431
59.INSTALL BATTERY TRAY
28800
60.INSTALL BATTERY
Install the battery onto the vehicle with the battery clamp.
Connect the cable to the battery terminal.
55711
61.INSTALL OUTER COWL TOP PANEL
55722C
62.INSTALL INNER COWL TOP TO COWL BRACE
55815E
63.INSTALL FRONT NO. 1 VENTILATOR SEAL
55735D
64.INSTALL FRONT AIR SHUTTER SEAL RH
65.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
66.INSTALL FRONT WHEELS
16361A
67.INSPECT FAN AND GENERATOR V BELT
68.ADD ENGINE COOLANT
69.INSPECT ENGINE OIL LEVEL
70.ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
71.INSPECT AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
72.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
73.INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)
74.INSPECT FOR COOLANT LEAK
75.INSPECT FOR OIL LEAK
76.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK
77.INSPECT FOR MANUAL TRANSAXLE OIL LEAK
78.INSPECT FOR FUEL LEAK
79.INSPECT FOR EXHAUST GAS LEAK
Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
80.INSPECT IGNITION TIMING
81.INSPECT ENGINE IDLING SPEED
82.INSPECT CO/HC
83.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
51441C
84.INSTALL ENGINE UNDER COVER RH
51442C
85.INSTALL ENGINE UNDER COVER LH
11212
86.INSTALL NO. 2 CYLINDER HEAD COVER
87.INSPECT ABS SENSOR SIGNAL (w/o VSC)
88.INSPECT VSC SPEED SENSOR SIGNAL (w/ VSC)