Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2017.01
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate whether the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal conditions are as shown in the table below.


Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal is released
(c) STP signal is off when ST1- signal is off
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A395241E01
0.396,1.708 0.854,1.906 0.458,0.198 10 false ALT 0.76,0.563 1.375,0.76 0.615,0.198 10 false STOP 0.563,4.448 1.635,4.646 1.073,0.198 10 false Battery 0.99,3.313 1.604,3.51 0.615,0.198 10 false MAIN 2.031,3.313 2.49,3.51 0.458,0.198 10 false R/I 0.729,3.552 2.781,3.792 2.052,0.24 10 false from Ignition Switch Assembly 3.76,0.406 3.917,0.604 0.156,0.198 10 false B 3.76,0.917 3.917,1.115 0.156,0.198 10 false B 3.76,1.365 4.219,1.563 0.458,0.198 10 false GND 4.625,0.406 4.781,0.604 0.156,0.198 10 false L 4.625,1.365 4.781,1.563 0.156,0.198 10 false L 3.427,0.135 3.885,0.333 0.458,0.198 10 false 7*1 3.427,0.302 3.885,0.5 0.458,0.198 10 false 1*2 4.833,0.135 5.292,0.333 0.458,0.198 10 false 3*1 4.833,0.302 5.292,0.5 0.458,0.198 10 false 2*2 3.427,0.635 3.885,0.833 0.458,0.198 10 false 6*1 3.427,0.802 3.885,1 0.458,0.198 10 false 5*2 4.833,1.083 5.292,1.281 0.458,0.198 10 false 5*1 4.833,1.25 5.292,1.448 0.458,0.198 10 false 4*2 3.427,1.083 3.885,1.281 0.458,0.198 10 false 2*1 3.427,1.25 3.885,1.448 0.458,0.198 10 false 3*2 5.74,0.302 5.896,0.5 0.156,0.198 10 false 9 5.667,1.25 5.979,1.448 0.313,0.198 10 false 10 5.948,0.302 6.406,0.5 0.458,0.198 10 false STP 5.948,1.25 6.563,1.448 0.615,0.198 10 false ST1- 3.396,1.677 4.167,1.875 0.771,0.198 10 false A92*1 3.396,1.844 4.167,2.042 0.771,0.198 10 false A91*2 3.385,2.01 5.333,2.219 1.948,0.208 10 false Stop Light Switch Assembly 6.26,4.365 6.719,4.563 0.458,0.198 10 false A83 6.25,4.542 6.708,4.74 0.458,0.198 10 false ECM 3.698,2.75 4.156,2.948 0.458,0.198 10 false IG2 4.417,3.906 4.875,4.104 0.458,0.198 10 false IG2 4.771,4.031 5.083,4.229 0.313,0.198 10 false 10 5.021,4.042 5.333,4.24 0.313,0.198 10 false 1E 3.219,2.438 3.531,2.635 0.313,0.198 10 false 19 3.208,2.615 3.521,2.813 0.313,0.198 10 false 1D 3.26,2.99 3.417,3.188 0.156,0.198 10 false 1 3.219,3.167 3.531,3.365 0.313,0.198 10 false 1C 3.219,3.406 3.531,3.604 0.313,0.198 10 false 17 3.208,3.583 3.521,3.781 0.313,0.198 10 false 1D 3.469,4.25 5.229,4.49 1.76,0.24 10 false No. 1 Integration Relay 1.438,4.885 3.635,5.135 2.198,0.25 10 false *1: w/ Toyota Safety Sense 1.438,5.25 3.625,5.5 2.188,0.25 10 false *2: w/o Toyota Safety Sense

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON and turn the GTS on.

(c)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

(d)

Check the STP signal when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK SPECIFICATIONS
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Toyota Safety Sense A
w/o Toyota Safety Sense B



A

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

B

7.CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL VOLTAGE)
2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
E270270C33
0.25,0.917 0.667,1.167 0.417,0.25 2.365,1.198 2.667,1.875 true 0.333,0.958 0.792,1.156 0.458,0.198 10 false A92 2.667,1.938 2.823,2.135 0.156,0.198 10 false B 0.115,0.188 0.427,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A92-7 (B) - Body ground Always 11 to 14 V




OK

3.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

3.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
E270270C34
0.25,0.917 0.667,1.167 0.417,0.25 2.146,1.219 2.448,1.896 true 0.333,0.958 0.792,1.156 0.458,0.198 10 false A92 2.448,1.917 2.604,2.115 0.156,0.198 10 false B 0.115,0.188 0.427,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A92-6 (B) - Body ground Ignition switch ON 11 to 14 V




OK

4.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

5.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.INSPECT ECM (STP AND ST1- VOLTAGE)
a.
U134152C02
2.24,3.344 1.958,4.281 true 2.313,3.354 2.677,4.302 true 1.833,0.531 2.635,0.844 0.802,0.313 10 false *b 0.281,0.531 1.052,0.854 0.771,0.323 10 false *a 0.417,2.552 0.677,2.76 0.26,0.208 10 false *c 1.823,4.344 2.167,4.542 0.344,0.198 10 false STP 2.594,4.333 2.969,4.542 0.375,0.208 10 false ST1- 0.271,3.458 0.594,3.667 0.323,0.208 10 false A83
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A83-10 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V



d.

Turn the ignition switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A83-9 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A92 stop light switch connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A92-6 (B) - 1D-19 Always Below 1 Ω
A92-6 (B) or 1D-19 - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
A389484C06
0.417,0.917 0.917,1.167 0.5,0.25 0.948,1.635 1.365,1.219 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.542,0.948 1,1.146 0.458,0.198 10 false A91 0.781,1.615 1.24,1.813 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-1 (B) - Body ground Always 11 to 14 V




OK

8.CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

8.CHECK STOP LAMP SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
A389484C07
0.417,0.917 0.917,1.167 0.5,0.25 2.417,1.667 2.104,1.219 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.542,0.948 1,1.146 0.458,0.198 10 false A91 2.448,1.688 2.906,1.885 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A91-5 (B) - Body ground Ignition switch ON 11 to 14 V




OK

9.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
9.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

10.INSPECT ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.INSPECT ECM (STP AND ST1- VOLTAGE)
a.
U134152C02
2.24,3.344 1.958,4.281 true 2.313,3.354 2.677,4.302 true 1.833,0.531 2.635,0.844 0.802,0.313 10 false *b 0.281,0.531 1.052,0.854 0.771,0.323 10 false *a 0.417,2.552 0.677,2.76 0.26,0.208 10 false *c 1.823,4.344 2.167,4.542 0.344,0.198 10 false STP 2.594,4.333 2.969,4.542 0.375,0.208 10 false ST1- 0.271,3.458 0.594,3.667 0.323,0.208 10 false A83
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A83-10 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V



d.

Turn the ignition switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A83-9 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A91 stop light switch connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A91-5 (B) - 1D-19 Always Below 1 Ω
A91-5 (B) or 1D-19 - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR