Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU.

DTC No. DTC Detection Condition Trouble Area
C1422 When the stop light switch is OFF, the PMC terminal voltage is more than 0.86 V for 5 seconds or more.
·

Stop light switch

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Brake actuator assembly (Master cylinder pressure sensor)



WIRING DIAGRAM

C243291E05
0.698,1.125 1.104,1.281 0.406,0.156 10 false STOP 1.271,1.281 1.552,1.427 0.281,0.146 10 false A38 1.271,1.438 3.021,1.656 1.75,0.219 10 false Stop Light Switch Assembly 1.656,0.865 1.771,1.031 0.115,0.167 10 false 2 1.656,0.448 1.771,0.615 0.115,0.167 10 false 3 2.406,0.865 2.521,1.031 0.115,0.167 10 false 1 2.406,0.448 2.521,0.615 0.115,0.167 10 false 4 3.969,1.375 4.875,1.563 0.906,0.188 10 false to Stop Lights 5.448,0.865 5.542,1.01 0.094,0.146 10 false 2 5.625,0.958 5.948,1.115 0.323,0.156 10 false STP 5.208,1.927 6.781,2.313 1.573,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.219,1.75 5.5,1.906 0.281,0.156 10 false A54

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C1425 is output together with C1422, inspect and repair the trouble areas indicated by C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1425).


PROCEDURE

1.CHECK DTC
a.

Check the DTC C1425 is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1425 is not output A
DTC C1425 is output B



A

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)

B

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menu: Chassis / ABS/VSC/TRC / Data List.


e.

In accordance with the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch/OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-
Master Cylinder Sensor Master cylinder pressure sensor reading/Min.: 0 V, Max.: 5 V 0.3 to 0.9 V: When brake pedal is released Reading increases when brake pedal is depressed.

Standard Voltage:

Master cylinder pressure sensor reading is 0.86 V or less at the instant the stop light switch changes from off to on.




OK

3.RECONFIRM DTC

NG

4.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).



Result
Result Proceed to
DTC C1422 is not output A
DTC C1422 is output B


A

B

4.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation. (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION)

OK:

The brake pedal height and stop light switch installation are normal.




OK

5.INSPECT STOP LIGHT SWITCH

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

5.INSPECT STOP LIGHT SWITCH
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)

NG

REPLACE STOP LIGHT SWITCH

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-2 (STP) - A38-1 Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR