Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM19S0E _55 Steering _051480 POWER ASSIST SYSTEMS _0248253 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1513  Torque Sensor Deviation Excessive  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

The Hall IC is a duplex system, and the power steering ECU assembly monitors the total value of TRQ1 (Hall IC 1) voltage and TRQ2 (Hall IC 2) voltage to detect malfunctions in the torque sensor (steering column sub-assembly).

While DTC C1513 is detected, power assist is stopped due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1512 Torque Sensor Deviation Excessive Deviation of torque sensor TRQ1 and TRQ2 exceeds specified values Torque sensor (Steering column sub-assembly) EPS warning light: Comes on Ignition switch ON again

WIRING DIAGRAM

C375647E09
0.271,3.01 2.281,3.385 2.01,0.375 10 false Torque Sensor (Steering Column Sub-assembly) 5.854,0.615 6.167,0.813 0.313,0.198 10 false 5V 5.083,0.833 5.698,1.031 0.615,0.198 10 false TRQV 5.115,1.406 5.729,1.604 0.615,0.198 10 false TRQ1 5.115,1.896 5.729,2.094 0.615,0.198 10 false TRQ2 5.083,2.26 5.698,2.458 0.615,0.198 10 false TRQG 4.885,0.813 5.042,1.01 0.156,0.198 10 false 8 4.885,1.26 5.042,1.458 0.156,0.198 10 false 9 4.875,1.781 5.031,1.979 0.156,0.198 10 false 1 4.885,2.25 5.042,2.448 0.156,0.198 10 false 2 4.813,2.958 5.125,3.156 0.313,0.198 10 false z6 4.813,3.115 6.948,3.438 2.135,0.323 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

OK:

DTC C1511 and C1512 are not output.


Result
Result Proceed to
DTCs C1511 and C1512 are not output A
DTC C1511 is output B
DTC C1512 is output C



A

2.CLEAR DTC

B

C

2.CLEAR DTC

NEXT

3.CONFIRM DTC
3.CONFIRM DTC
a.

Start the engine.


b.

With the vehicle stopped, turn the steering wheel all the way to the left and right.

HINT:

Turn the wheel both strongly and gently when steering back and forth.



c.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

OK:

DTC C1513 is not output.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

REPLACE STEERING COLUMN SUB-ASSEMBLY

C

REPLACE STEERING COLUMN SUB-ASSEMBLY