Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.

DTC No.
DTC Detection Condition
Trouble Area
P0016
Deviation in crankshaft and camshaft position sensor signals (2 trip detection logic)
  1. Mechanical system (Timing chain has jumped tooth or chain stretched)
  2. OCV
  3. OCV filter
  4. Camshaft timing gear assembly
  5. ECM

CONFIRMATION DRIVING PATTERN


A197314E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0016.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


WIRING DIAGRAM

Refer to DTC P0010 .

INSPECTION PROCEDURE

HINT:
  1. The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    DTC P0016 is output
    A
    DTC P0016 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0016 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Turn the Techstream on.

  1. Turn the A/C switch on.

  1. Warm up the engine.

  1. On the Techstream, enter the following menu: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

    OK:

    Techstream Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    HINT:
    Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1] (Click here).



NG
Go to step 4
OK


3.ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 7

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV)
  1. Inspect the OCV (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


5.INSPECT OIL CONTROL VALVE FILTER
A050664E08
  1. Remove the OCV filter.

  1. Check that the filter is not clogged.

    OK:
    Filter is not clogged.

    Text in Illustration 
    *1
    OCV Filter

  1. Reinstall the OCV filter.



NG
CLEAN OR REPLACE OIL CONTROL VALVE FILTER
OK


6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read pending DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0016 is output
    B



B
REPLACE ECM (Click here)
A

END